Laserfiche WebLink
0 <br />emulsion This matenai H not hazardous when used vnthin container. <br />reasonable standards of industrial hygiene and safe working <br />practices. Refer to MOOS, Protect from freezing. CT-R C not freezeithaw stable <br />AN IXONICS COMPANY ISO 8001 CERTIFIED NASDAQ LiSTED affix <br />CT-R <br />a!' chromaline Chromeline Screen Print Products <br />4832 G•and Ave • Duluth Stonesola 55301 • Tel 218-628-2217 • Fax 218 628 3245 <br />Web SRO we* chrornahne cant • E-mail attles@chrornahne corn <br />INSTRUCTIONS <br />DEGREASE <br />Using ChromeiClean '11 mesh degreaser. <br />work up a lather on both sides of mesh <br />Flood screen and frame thoroughly with <br />garden type hose, than dry <br />COAT <br />Slowly apply first coat to pnnt side Then coat squeegee <br />side with one coal. If a thicker stencil is desired, additional <br />coats may be applied to print see. Note that one coat on <br />each side with CT-R is smear to four coats wet on wet with <br />typical diazo based emulsions Dry thoroughly between <br />coats. <br />Note <br />CT-R is presensitized Stir before use <br />Keep pail covered Mien not in use <br />Return unused emulson ham scoop <br />coater to pail as soon as possible. <br />Emulsion dries quickly and will rapidly <br />'skin over <br />DRY <br />Thoroughly dry screen in honzontal <br />position, print side down, using a total- <br />ly dark, clean drying cabinet <br />Temperature should not exceed 110T <br />(43°C) <br />EXPOSE <br />Place emulsion side of photopositive <br />contact with pont side of screen <br />Exposure times for CIA are very short <br />and accurate exposure is important for <br />optimal results See exposure guide- <br />lines at right <br />DEVELOP <br />Gently spray both sides of screen with <br />lukewarm water, watt 30 seconds then <br />gently wash print side of the screen until <br />image is tuff), open Rinse both sees <br />thoroughly Dry screen completely and <br />you are ready to pnnt. <br />RECLAIM <br />Apply Chrome/Strip'. Screen <br />rectarrner to both sides of screen <br />Scrub area to be reclaimed with a <br />Off nylon brush to ensure entire <br />surface is wet and lel It work a few <br />moments until stencil begins to dis- <br />solve Remove stencil residue with <br />pressure washer, then rinse with <br />garden type hose, thoroughly flood. <br />ing screen and frame <br />EXPOSURE GUIDELINES <br />Note. Exposure times are suggested only as a guide <br />Use the step exposure method to determine optimal <br />exposure times, Individual exposure limes may vary <br />depending upon equipment used, bulb age. and <br />other shop conditions Exposure tones below were <br />set for 5KW and at 40 from frame <br />110 YELLOW POLYESTER <br />NIONOFILAMENT MESH <br />Coating Coster Suggested <br />Technique Edge We. Exp. Time <br />1X1 Round 30 sec <br />1X2 Round 40 sec <br />103 Round 50 sec <br />230 YELLOW POLYESTER <br />MONOFILAMENT MESH <br />Coating Coster Suggested <br />Technique Edge MM. Exp. Time <br />1X1 Round 20 sec <br />1X2 Round 25 sec <br />1X3 Round 30 sec <br />390 YELLOW POLYESTER <br />MONOFILAMENT MESH <br />Coating Coater Suggested <br />Technique Edge Min. Exp. Time <br />Xi Round 15 sec <br />102 Round 20 sec. <br />103 Round 25 sec <br />Extratire Arras ewe Neennned CNN re CHROMALNE <br />EXPOSURE CALCUtATOR <br />For Technical Service <br />Call Toll Free 1-800-328-4261 <br />FM2I1' halnarlirnmalina enm