Laserfiche WebLink
FIBERGLASS - COMPOSITE PIPE GROUP - HEADQUARTERS <br />P.O. Box 801148 • Houston, TX 77280 • Tel: (713) 690-7777 • Fax: (713) 690-2842 • http://www.ameron.com <br />Europe <br />Ameron B.V. <br />J.F. Kennedylaan 7 <br />4191 MZ Geldermalsen <br />The Netherlands <br />Tel: +31 345 587 587 <br />Fax: +31 345 587 561 <br />Americas <br />P.O. Box 878 <br />Burkburnett, TX 76354 <br />Tel: (940) 569-1471 <br />Fax: (940) 569-2764 <br />Centron International <br />P.O. Box 490 <br />600 FM 1195 South <br />Mineral Wells, Texas 76068 <br />Tel: (940) 325-1341 <br />Fax: (940) 325-9681 <br />Asia <br />Ameron (Pte) Ltd. <br />No. 7A, Tuas Avenue 3 <br />Singapore 639407 <br />Tel: 65 861 6118 <br />Fax: 65 862 1302/861 7834 <br />©1997 Ameron FP737E (01/02) supercedes FP737D (6/00) Printed in U.S.A. 5M [186] <br />Bending radius Minimum Maximum Minimum <br />Nominal Bending Deflection Length Required <br />Pipe Size Radius <br />1 per 20-ft Joint for 10° Change <br />(in)(mm)(ft)(m)(deg) (ft)(m) <br />2 50 75 23 15 13 4 <br />3 80 125 38 9 22 7 <br />4 100 150 46 7.5 27 8 <br />1) At rated pressure. Sharper bends may create excessive stress concentrations. Do not bend pipe until <br />adhesive has cured. <br />Method <br />Pipe Property1 Units Value <br />1 ASTM ATM <br />2 <br />Tensile strength <br />Longitudinal 10 <br />3 psi 35.0 D2105 161 <br />MPa 241 <br />Circumferential 10 <br />3 psi 70.0 D1599 151 <br />MPa 483 <br />Tensile modulus <br />Longitudinal 10 <br />6 psi 3.0 D2105 161 <br />GPa 20.7 <br />Circumferential 10 <br />6 psi 4.2 — — <br />GPa 29.0 <br />Compressive strength <br />Longitudinal 10 <br />3 psi 35.0 — 142 <br />MPa 241 <br />Compressive modulus <br />Longitudinal 10 <br />6 psi 3.0 — 142 <br />GPa 20.7 <br />Long-term hydrostatic <br />design basis <br />Static 10 <br />3 psi 31.5 D2992(B) — <br />MPa 217 <br />Cyclic 10 <br />3 psi 8.0 D2992(A) — <br />MPa 55 <br />Poisson’s ratio3 <br />yx — <br />0.16 — — <br />xy — <br />0.26 — — <br />1) Based on structural wall thickness. <br />2) Ameron test method. <br />3) The first subscript denotes the direction of contraction <br />and the second that of the applied stress. <br />x denotes longitudinal direction. <br />y denotes circumferential direction. <br />Typical mechanical <br />properties of <br />primary pipe <br />Important Notice This literature and the information and recommendations it contains are based on data reasonably believed to be <br />reliable. However, such factors as variations in environment, application or installation, changes in operating <br />procedures, or extrapolation of data may cause different results. Ameron makes no representation or warranty, <br />express or implied, including warranties of merchantability or fitness for purpose, as to the accuracy, adequacy or <br />completeness of the recommendations or information contained herein. Ameron assumes no liability whatsoever in <br />connection with this literature or the information or recommendations it contains. Product specifications are subject <br />to change.