|
CONSTRUCTION NOTES ENTRANCES AND DOORS 7. HANDRAILS AT THE TOP OF STAIRWAYS SHALL EXTEND A MINIMUM OF 12 INCHES OF LEVEL DISTANCE TOILET ROOM IDENTIFICATION SYMBOLS 10. A CLEAR SPACE,MEASURED FROM THE FLOOR TO A HEIGHT OF 27 INCHES ABOVE THE FLOOR,WITHIN THE
<br /> 1. CONSTRUCT SIDEWALKS WITH THE SLOPE 0.5%LESS THAN THE MAXIMUM ALLOWABLE ADA STANDARD. 1. ALL PRIMARY ENTRANCES AND EXTERIOR GROUND FLOOR EXIT DOORS TO BUILDINGS AND FACILITIES BEYOND THE TOP NOSING. HANDRAILS AT THE BOTTOM OF STAIRWAYS SHALL EXTEND A MINIMUM OF 1. DOOR MOUNTED SIGNAGE SANITARY FACILITY ROOM,OR SUFFICIENT SIZE TO INSCRIBE A CIRCLE OF A DIAMETER NOT LESS THAN 60
<br /> 2. ALL CLEAR DISTANCES ARE"CLEAR"TO THE FACE OF FINISH AND/OR VENEER. SHALL BE MADE ACCESSIBLE TO THE PHYSICALLY DISABLED. TREAD WIDTH PLUS 12 INCHES BEYOND THE BOTTOM NOSING BEFORE THEY ARE RETURNED. AT THE 1.1. (MEN'S)-EQUILATERAL TRIANGLE 1/4 INCH THICK WITH EDGES 12 INCHES LONG AND A VERTEX INCHES,OR A CLEAR SPACE NO LESS THAN 56 INCHES BY 63 INCHES IN SIZE SHALL BE PROVIDED. DOORS
<br /> 2. ALL ACCESSIBLE ENTRANCES SHALL BE IDENTIFIED WITH AT LEAST ONE STANDARD SIGN AND WITH BOTTOM,THE HANDRAIL SHALL CONTINUE TO SLOPE FOR A DISTANCE OF THE WIDTH OF ONE TREAD FROM POINTING UPWARD. OTHER THAN THE DOOR TO THE DISABLED TOILET COMPARTMENT,IN ANY POSITION,MAY NOT ENCROACH
<br /> THE BOTTOM RISER. THE REMAINDER OF THE EXTENSION SHALL BE HORIZONTAL(LEVEL). 1.2. WOMEN'S 12 INCH DIAMETER CIRCLE 1/4 INCH THICK. INTO THIS SPACE BY MORE THAN 12 INCHES. THIS CLEAR SPACE MAY INCLUDE KNEE AND TOE
<br /> HAZARDS AND PROTRUDING OBJECTS ADDITIONAL DIRECTIONAL SIGNS,AS REQUIRED,VISIBLE FROM APPROACHING PEDESTRIAN WAYS. (WOMEN'S)
<br /> AT ALL TACTILE DOOR SIGNS,A CLEAR FLOOR SPACE AT LEAST 18 INCHES BY 18 INCHES CENTRED ON THE 8. WHERE THE EXTENSION OF THE HANDRAIL IN THE DIRECTION OF THE STAIR RUN WOULD CREATE A 1.3. (UNISEX)-12 INCH DIAMETER CIRCLE 1/4 INCH THICK WITH 1/4 INCH THICK TRIANGLE SUPERIMPOSED CLEARANCE SPACE UNDER FIXTURES.
<br /> 1. MINIMUM CLEAR FLOOR OR GROUND SPACE REQUIRED TO ACCOMMODATE A SINGLE,STATIONARY SIGN AND CLEAR OF ANY DOOR SWINGS SHALL BE PROVIDED. HAZARD,THE EXTENSION SHALL BE MADE AT RIGHT ANGLES,ON THE FACE OF A RETURNING WALL. WITHIN THE CIRCLE. 11. AN ACCESSIBLE INDIVIDUAL TOILET STALL SHALL PROVIDE AT LEAST 59 INCHES CLEAR FLOOR SPACE
<br /> WHEELCHAIR AND OCCUPANT IS 30 INCHES BY 48 INCHES. MINIMUM CLEAR FLOOR OR GROUND SPACE 4. EVERY REQUIRED ENTRANCE OR PASSAGE DOORWAY SHALL BE OF A SIZE AS TO PERMIT THE WHERE THE STAIRS ARE CONTINUOUS THE HANDRAIL SHALL BE CONTINUOUS AND NEED NOT EXTEND OUT 1.4. THE COLOR AND CONTRAST OF THE SIGN DISTINCTLY CONTRASTS WITH THE DOOR COLOR. FROM THE REAR WALL FOR FLOOR MOUNTED WATER CLOSETS AND 56 INCHES CLEAR FLOOR SPACE
<br /> FOR WHEELCHAIRS MAY BE POSITIONED FOR FORWARD OR PARALLEL APPROACH TO AN OBJECT. FLOOR INSTALLATION OF A DOOR NOT LESS THAN 36 INCHES IN WIDTH,AND NOT LESS THAN 80 INCHES IN HEIGHT. INTO THE LANDING. 1.5. SIGNS ARE CENTERED ON THE DOOR 60 INCHES FROM THE FLOOR. FROM THE REAR WALL FOR WALL MOUNTED WATER CLOSETS.
<br /> OR GROUND SPACE FOR WHEELCHAIRS MAY BE PART OF THE KNEE SPACE REQUIRED UNDER SOME DOORS SHALL BE CAPABLE OF OPENING AT LEAST 90 DEGREES AND SHALL BE MOUNTED SO THAT THE 9. ALL HANDRAIL ENDS SHALL BE RETURNED OR SHALL TERMINATE IN NEWEL POSTS OR SAFETY TERMINALS. 12. FOR ACCESSIBLE TOILET STALLS WITH DOORS ON THE END WALL,THERE MUST BE 48 INCHES CLEAR
<br /> OBJECTS. CLEAR WIDTH OF THE DOORWAY IS NOT LESS THAN 32 INCHES. 10. ALL HANDRAILS PROJECTED FROM A WALL SHALL HAVE AN ABSOLUTE CLEARANCE OF 1-112 INCHES 2. WALL MOUNTED SIGNAGE FROM THE FRONT-MOST POINT OF THE WATER CLOSET. THE SPACE BETWEEN THE CLEAR FLOOR SPACE
<br /> 2. PROVIDE AN ADDITIONAL 12 INCHES WIDTH ON ONE SIDE FOR ALCOVES GREATER THAN 15 INCHES DEEP 5. LATCHING AND LOCKING DOORS THAT ARE HAND ACTIVATED SHALL HAVE A TYPE OF LEVER HARDWARE, BETWEEN THE WALL AND THE HANDRAIL. 2.1. THE INTERNATIONAL SYMBOL OF ACCESSIBILITY IS INSTALLED ON THE WALL ADJACENT TO THE AND THE 48 INCHES IN FRONT OF THE WATER CLOSET IS CONSIDERED MANEUVERING SPACE. DOORS
<br /> AND DESIGNED FOR SIDE APPROACH. 11. THE HANDGRIP PORTION OF HANDRAILS SHALL BE NOT LESS THAN 1-1/4 INCH NOR MORE THAN 1-1/2 INCH MAY SWING INTO THE MANEUVERING SPACE.
<br /> 3. PROVIDE AN ADDITIONAL 6 INCHES WIDTH ON ONE SIDE FOR ALCOVES GREATER THAN 24 INCHES DEEP PANIC BARS,PUSH-PULL ACTIVATING BARS,OR OTHER HARDWARE DESIGNED TO PROVIDE PASSAGE LATCH SIDE OF THE DOOR. THE BORDER DIMENSIONS OF THIS PICTOGRAM SHALL BE A MINIMUM OF
<br /> af Q WITHOUT REQUIRING THE ABILITY TO GRASP THE OPENING HARDWARE. OUTSIDE DIAMETER IN CROSS-SECTION(1-1/2 STD.PIPE IS ACCEPTABLE)DIMENSION OR THE SHAPE 6 INCHES IN HEIGHT. WHERE THERE IS NO WALL SPACE ON THE LATCH SIDE,INCLUDING AT DOUBLE 13. FOR ACCESSIBLE TOILET STALLS WITH DOORS ON THE SIDE WALL THERE MUST BE 60 INCHES CLEAR
<br /> w o AND DESIGNED FOR FRONT APPROACH. 6. LEVER HAND ACTIVATED DOOR OPENING HARDWARE SHALL BE CENTERED BETWEEN 34 INCHES AND 44 SHALL PROVIDE AN EQUIVALENT SMOOTH GRIPPING SURFACE WITH NO SHARP CORNERS. LEAF DOORS,SIGNS SHALL BE PLACED ON THE NEAREST ADJACENT WALL,PREFERABLY ON THE FROM THE FRONT MOST POINT OF THE WATER CLOSET. THE SPACE BETWEEN THE CLEAR FLOOR SPACE
<br /> 0 4. OBJECTS PROJECTING FROM WALLS WITH THEIR LEADING EDGES BETWEEN 27 INCHES AND 80 INCHES INCHES MAXIMUM ABOVE THE FLOOR. RIGHT. AND THE 60 INCHES IN FRONT OF THE WATER CLOSET IS CONSIDERED MANEUVERING SPACE. DOORS
<br /> LL Q ABOVE THE FINISHED FLOOR SHALL PROTRUDE NO MORE THAN 4 INCHES INTO WALKS,HALLS, MAY SWING INTO THE MANEUVERING SPACE.
<br /> 0 0 7. THE FLOOR OR LANDING LENGTH ON EACH SIDE OF AN ENTRANCE OR PASSAGE DOOR SHALL BE LEVEL RAMPS 2.2. DESCRIPTION AS TO TOILET ROOM USAGE(I.E.MEN'S TOILET ROOM,ETC.)IS PLACED DIRECTLY 14. FOR ACCESSIBLE TOILET STALLS WITH IN SWINING DOORS,THE END WALL MUST BE AT LEAST 36 INCHES
<br /> CORRIDORS,PASSAGEWAYS,OR AISLES. AND CLEAR AT LEAST 60 INCHES IN THE DIRECTION OF THE DOOR SWING AND AT LEAST 48 INCHES ° BELOW THE SYMBOL OF ACCESSIBILITY.
<br /> o Q 5. OBJECTS MOUNTED WITH THEIR LEADING EDGES AT OR BELOW 27 INCHES ABOVE THE FINISHED FLOOR 1. ALL RAMPS USED AS EXITS AND ANY PATH OF TRAVEL HAVING A SLOPE GREATER THAN 1:20(5/°)SHALL BEYOND THE REQUIRED CLEAR FLOOR SPACE.
<br /> co= MAY PROTRUDE ANY AMOUNT. OPPOSITE THE DIRECTION OF THE DOOR SWING AS MEASURED AT RIGHT ANGLES TO THE FACE OF THE COMPLY WITH THE REQUIREMENTS OF THIS SECTION. RAMPS SHALL HAVE THE LEAST POSSIBLE SLOPE. 2.3. THE CHARACTERS AND BACKGROUND OF THE SIGN IS EGGSHELL,MATTE,OR OTHER NON-GLARE
<br /> w DOOR IN THE CLOSED POSITION. THE WIDTH OF THE LEVEL AND CLEAR AREA ON THE SIDE WHICH THE 2. PEDESTRIAN RAMPS SERVING PRIMARY ENTRANCES TO A BUILDING SHALL HAVE A MINIMUM WIDTH OF 48 FINISH AND THE COLOR AND CONTRAST OF THE SIGN DISTINCTLY CONTRASTS WITH THE COLOR AND 15. WATER CLOSET COMPARTMENT SHALL BE EQUIPPED WITH A DOOR THAT HAS AN AUTOMATIC CLOSING
<br /> 6. FREESTANDING OBJECTS MOUNTED ON POSTS/PYLONS MAY OVERHANG 12 INCHES MAXIMUM FROM 27 DEVICE,AND A CLEAR UNOBSTRUCTED OPENING WIDTH OF 32 INCHES WHEN LOCATED AT THE END AND
<br /> w INCHES TO 80 INCHES ABOVE THE GROUND OR FINISHED FLOOR. DOOR SWINGS SHALL EXTEND A MINIMUM OF 24 INCHES PAST THE STRIKE EDGE OF THE DOOR FOR INCHES. CONTRAST OF THE WALL. 34 INCHES WHEN LOCATED AT THE SIDE WHEN THE DOOR IS POSITIONED AT AN ANGLE OF 90 DEGREES
<br /> 7. PROTRUDING OBJECTS SHALL NOT REDUCE THE REQUIRED CLEAR WIDTH OF AN ACCESSIBLE ROUTE OR DOORS WITH LATCH SIDE APPROACH AND 36 INCHES FOR DOORS REQUIRING HINGE SIDE APPROACH. 3. ALL RAMPS IN AREAS ACCESSIBLE TO PERSONS WITH DISABILITIES ON A PATH OF TRAVEL OR SERVING 2.4. SIGNS WITH RAISED CHARACTERS AND BRAILLE SHALL BE LOCATED 48 INCHES MINIMUM ABOVE THE V!v A�{� a rC�itectu re
<br /> FROM ITS CLOSED POSITION. DOOR SHALL HAVE A 9 INCH MINIMUM CLEAR OPENING FROM FINISH FLOOR
<br /> MANEUVERING SPACE. REFER TO ACCESSIBLE DETAILS FOR ADDITIONAL CLEARANCE REQUIREMENTS ON SHEET ADA-2. EXITS SHALL HAVE A 1:12.5(8.0%)MAXIMUM SLOPE WITH CROSS SLOPES NO GREATER THAN 1:65(1.5%). FINISH FLOOR OR GROUND SURFACE,MEASURED FROM THE BASELINE OF THE LOWEST LINE OF TO BOTTOM OF DOOR. Design - Planning - Interiors
<br /> 8. ANY OBSTRUCTION OVERHANGING A PEDESTRIAN WAY SHALL BE A MINIMUM OF 80 INCHES ABOVE THE 8. THE FLOOR OR LANDING SHALL NOT BE MORE THAN 1/2 INCH LOWER THAN THE THRESHOLD OF THE 4. THE LEVEL LANDING WIDTH OF ANY RAMP SHALL EXTEND PAST THE STRIKE EDGE OF ANY DOOR OR GATE BRAILLE AND 60 INCHES MAXIMUM ABOVE THE FINISH FLOOR OR GROUND SURFACE,MEASURED
<br /> 0 16. ACCESSIBLE WATER CLOSET DOOR SHALL BE EQUIPPED ON THE INSIDE AND OUTSIDE WITH HANDLES OF 637 5th Avenue San Rafael, CA 94901
<br /> w WALKING SURFACE AS MEASURED TO THE BOTTOM OF THE OBSTRUCTION. DOORWAY. CHANGES IN LEVEL BETWEEN 1/4 INCH AND 1/2 INCH SHALL BE LEVELED WITH A SLOPE NO AS SHOWN ON DETAILS. FROM THE BASELINE OF THE HIGHEST LINE OF RAISED CHARACTERS. MOUNTING LOCATION SHALL A LOOP OR U SHAPED DESIGN AND LOCATED IMMEDIATELY ABOVE THE LATCH. THE LATCH SHALL BEA 415-451-2500 415-451-2595 fax
<br /> M GREATER THAN 1:2. 5. DOORS STANDING IN ANY POSITION SHALL NOT REDUCE THE MINIMUM DIMENSION OF THE RAMP TO LESS BE DETERMINED SO THAT A PERSON MAY APPROACH WITHIN 3 INCHES OF SIGNAGE WITHOUT www.vmarch.com
<br /> W > FLIP OVER,SLIDING OR OTHER HARDWARE SO AS NOT TO REQUIRE GRASPING OR TWISTING.
<br /> W 0 9. THE BOTTOM 10 INCHES OF ALL DOORS(EXCEPT AUTOMATIC AND SLIDING)SHALL HAVE A SMOOTH THAN 42 INCHES OR THE REQUIRED WIDTH BY MORE THAN 3 INCHES WHEN FULLY OPEN(CA.ONLY). ENCOUNTERING PROTRUDING OBJECTS OR STANDING WITHIN THE SWING OF A DOOR.
<br /> o a PARKING UNINTERRUPTED SURFACE TO ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST WITHOUT 6. ALL CURB RAMPS SHALL BE PROVIDED WITH TRUNCATED DOMES TO COMPLY WITH THE MINIMUM 2.5. LETTERS AND NUMERALS ARE RAISED 1/32 INCH,ARE SANS-SERIF UPPERCASE CHARACTERS,AREA 17. EXCEPT FOR DOOR OPENINGS,A CLEAR UNOBSTRUCTED ACCESS NOT LESS THAN 44 INCHES SHALL BE
<br /> CO
<br /> o 1. SURFACE SLOPES OF ACCESSIBLE PARKING SPACES FOR THE PHYSICALLY DISABLED SHALL NOT EXCEED CREATING A TRAP OR HAZARDOUS CONDITION. WHERE NARROW FRAME DOORS ARE USED,A 10 INCH REQUIREMENTS OF A.D.A.A.G.AND THE LATEST CA-24 ACCESS REQUIREMENTS. MINIMUM 5/8 INCH HIGH AND A MAXIMUM OF 2 INCHES HIGH,AND ARE ACCOMPANIED BY GRADE 2 PROVIDED TO ALL WATER CLOSET COMPARTMENTS DESIGNED FOR USE BY THE DISABLED. VMI JOB NUMBER
<br /> � w 3/16 INCH PER FOOT(2%GRADIENT)IN ANY DIRECTION. HIGH SMOOTH PANEL SHALL BE INSTALLED ON THE PUSH SIDE OF THE DOOR WHICH WILL ALLOW THE 7. HANDRAILS ARE REQUIRED ON RAMPS WHEN THE SLOPE EXCEEDS 1:20(5%). HANDRAILS AT RAMPS SHALL BRAILLE. 18. TOE CLEARANCE SHALL EXTEND AT LEAST 6"BEYOND AT LEAST ONE SIDE PARTITION OF AN ACCESSIBLE
<br /> U)E 2. DISABLED PARKING SPACES SHALL BE LOCATED SO AS NOT TO REQUIRE USERS TO WHEEL OR WALK DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST. RUN ALONG BOTH SIDES OF A RAMP,BE CONTINUOUS THE FULL LENGTH,HANDRAILS SHALL EXTEND A TOILET STALL UNLESS THE COMPARTMENT IS GREATER THAN 66 INCHES WIDE. THE UNDERSIDE OF ALL 20049
<br /> BEHIND ANY OTHER NON DISABLED OR DISABLED PARKING SPACE. 10. THE MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED 5 LBS.FOR ALL EXTERIOR AND INTERIOR PARTITIONS SHALL BE SMOOTH AND FREE FROM SHARP EDGES OR ABRASIVE SURFACES.
<br /> _ MINIMUM OF 12 INCHES OF LEVEL DISTANCE BEYOND THE TOP AND BOTTOM OF THE RAMP.HANDRAIL TOILET ROOM FIXTURES AND STALLS
<br /> } 3. IN EACH PARKING AREA,A BUMPER OR CURB SHALL BE PROVIDED AND LOCATED TO PREVENT DOORS. SUCH PULL OR PUSH EFFORT BEING APPLIED AT RIGHT ANGLES TO HINGED DOORS AND AT THE EXTENSIONS SHALL RETURN TO THE LAST SUPPORT OF THE HANDRAIL. 1. THE HEIGHT OF ACCESSIBLE WATER CLOSETS SHALL BE 17 INCHES MINIMUM AND 19 INCHES MAXIMUM
<br /> a ENCROACHMENT OF CARS OVER THE REQUIRED WIDTH OF WALKWAYS. 8. THE HANDRAIL GRIP SURFACE AT RAMPS SHALL BE MOUNTED BETWEEN 34 INCHES AND 38 INCHES ABOVE �� ARC
<br /> o CENTER PLANE OF SLIDING OR FOLDING DOORS. COMPENSATING DEVICES OR AUTOMATIC DOOR MEASURED TO THE TOP OF THE SEAT. TOILET ROOM GRAB BARS
<br /> 0� 4. PARKING SPACES RESERVED FOR PERSONS WITH PHYSICAL DISABILITIES SHALL BE IDENTIFIED BY A OPERATORS MAY BE UTILIZED TO MEET THE ABOVE STANDARDS. WHEN FIRE DOORS ARE REQUIRED,THE THE RAMP SURFACE. GRAB BARS SHALL BE LOCATED ON ONE SIDE AND THE BACK OF THE PHYSICALLY DISABLED TOILET STALL
<br /> 1.
<br /> o m REFLECTIVE SIGN PERMANENTLY POSTED IMMEDIATELY ADJACENT TO AND VISIBLE FROM EACH STALL OR MAXIMUM EFFORT TO OPERATE THE DOOR MAY NOT EXCEED 15 LBS. 2. THE CENTER LINE 0 THE ACCESSIBLE WATER CLOSET SHALL BE 17 INCHES MINIMUM AND 18 INCHES OR COMPARTMENT AND SHALL BE SECURELY ATTACHED 33 INCHES MINIMUM AND 36 INCHES MAXIMUM Al?b
<br /> 9. RAMPS WITH A RISE GREATER THAN 6 INCHES SHALL HAVE HANDRAILS ON BOTH SIDES. MAXIMUM FROM SIDE WALL OR PARTITION. y
<br /> 0 w SPACE,CONSISTING OF A PROFILE VIEW OF A WHEELCHAIR WITH OCCUPANT IN WHITE ON DARK BLUE ABOVE AND PARALLEL TO THE FLOOR MEASURED TO THE TOP OF THE GRIPPING SURFACE.
<br /> 0 m 10. GUARDS SHALL BE LOCATED ALONG OPEN SIDED WALKING SURFACES,STAIRWAYS,RAMPS AND LANDINGS 3. TOILET AND URINAL FLUSH CONTROLS SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE
<br /> Q1— BACKGROUND. THE SIGN SHALL NOT BE SMALLER THAN 70 INCHES IN AREA AND,WHEN IN THE PATH OF STAIRWAYS THAT ARE LOCATED MORE THAN 30 INCHES ABOVE THE FLOOR OR GRADE BELOW.GUARDS SHALL BE 42 2. SIDE GRAB BARS SHALL BE AT LEAST 42 INCHES LONG WITH THE FRONT END POSITIONED AT LEAST 54
<br /> 0 TIGHT GRASPING,PINCHING,OR TWISTING OF THE WRIST. CONTROLS FOR THE FLUSH VALVES SHALL BE
<br /> 0� TRAVEL,SHALL BE POSTED AT A MINIMUM HEIGHT OF 80 INCHES FROM THE BOTTOM OF THE SIGN TO TOP INCHES FROM THE REAR WALL AND THE BACK END NO LESS THAN 12 INCHES FROM THE REAR WALL.
<br /> Of J 1. STAIRWAYS SHALL HAVE INTERMEDIATE HANDRAILS LOCATED IN SUCH A MANNER THAT ALL PORTIONS OF INCHES HIGH,MEASURED VERTICALLY ABOVE ADJACENT WALKING SURFACE. GUARDS SHALL HAVE MOUNTED ON THE OPEN(WIDE)SIDE OF THE TOILET STALL,NO MORE THAN 44 INCHES ABOVE THE FLOOR. * x
<br /> OF SIDEWALK. SIGNS MAY ALSO BE CENTERED ON THE WALL AT THE INTERIOR END OF THE PARKING GRAB BARS AT THE BACK STALL SHALL NOT BE LESS THAN 36 INCHES LONG AND EXTEND A MINIMUM OF 12 No. 017928
<br /> C) THE STAIRWAY WIDTH REQUIRED FOR EGRESS CAPACITY ARE WITHIN 30 INCHES OF A HANDRAIL. BALUSTERS OR ORNAMENTAL PATTERN SUCH THAT A 4-INCH-DIAMETER SPHERE CANNOT PASS THROUGH THE FORCE REQUIRED TO ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5 LBS.
<br /> LL CO SPACE AT A MINIMUM HEIGHT OF 36 INCHES FROM THE PARKING SPACE FINISHED GRADE,GROUND,OR ANY OPENING. INCHES FROM THE CENTERLINE OF THE WATER CLOSET ON ONE SIDE AND A MINIMUM OF 24 INCHES FROM REN. 10/31/23
<br /> w SIDEWALK WHICHEVER IS HIGHEST). 2. STAIR RISER HEIGHTS SHALL BE 7 INCHES MAXIMUM AND 4 INCHES MINIMUM. THE RISER HEIGHT SHALL BE 4. WHERE URINALS ARE PROVIDED,AT LEAST ONE SHALL HAVE A CLEAR SPACE 30 INCHES WIDE BY 48
<br /> ( ) MEASURED VERTICALLY BETWEEN THE LEADING EDGES OF ADJACENT TREADS. RECTANGULAR TREAD INCHES LONG IN FRONT OF THE URINAL. AT LEAST ONE URINAL WITH A RIM PROJECTING A MINIMUM OF THE CENTERLINE OF THE WATER CLOSET ON THE OTHER SIDE.af
<br /> Uj o DEPTHS SHALL BE 11 INCHES MINIMUM MEASURED HORIZONTALLY BETWEEN THE VERTICAL PLANES OF BABY CHANGING TABLE (WHEN PROVIDED) 13.5 INCHES FROM THE BACK OF THE FIXTURE AND A MAXIMUM OF 17 INCHES ABOVE THE FLOOR SHALL 3. THE DIAMETER OR WIDTH OF THE GRIPPING SURFACES OF A GRAB BAR SHALL BE 1 114 INCHES OR THE 0
<br /> Z o WALKS AND SIDEWALKS THE FOREMOST PROJECTION OF ADJACENT TREADS AND AT RIGHT ANGLE TO THE TREADS LEADING EDGE. BE INSTALLED. SHAPE SHALL PROVIDE AN EQUIVALENT GRIPPING SURFACE. IF THE GRAB BARS ARE MOUNTED �F CALZ�
<br /> 1. WALKS AND SIDEWALKS SHALL HAVE A CONTINUOUS COMMON SURFACE NOT EXCEEDING 2/°CROSS 1. BABY CHANGING TABLES WHEN DEPLOYED SHALL NOT OBSTRUCT THE REQUIRED WIDTH OF AN
<br /> o ° ADJACENT TO A WALL,THE SPACE BETWEEN THE WALL AND THE GRAB BARS SHALL BE 1 1/2 INCHES.
<br /> 3. THE UPPER APPROACH AND THE LOWER TREAD OF EACH INTERIOR STAIR,AND ALL EXTERIOR STAIR ACCESSIBLE ROUTE EXCEPT CAN PROJECT MAXIMUM 4"BETWEEN 27"&80"ABOVE FINISH FLOOR. 5. A CLEAR FLOOR SPACE 30 INCHES WIDE BY 48 INCHES LONG SHALL BE PROVIDED IN FRONT OF A
<br /> SLOPE AND SHALL NOT BE INTERRUPTED BY STEPS OR BY ABRUPT CHANGES IN LEVEL WHICH EXCEED 1/4 TREADS,SHALL BE MARKED BY A STRIP OF CLEARLY CONTRASTING COLOR AT LEAST 2 INCHES WIDE AND CHANGING TABLES SHALL NOT BE LOCATED TOILET COMPARTMENTS THAT ARE WHEELCHAIR ACCESSIBLE LAVATORY TO ALLOW FORWARD APPROACH. SUCH CLEAR SPACE SHALL ADJOIN OR OVERLAP AN 4. GRAB BARS AND ANY WALL OR OTHER SURFACE ADJACENT TO THEM SHALL BE FREE OF ANY SHARP OR
<br /> U) INCH,AND SHALL BE A MINIMUM OF 48 INCHES IN WIDTH. SURFACES SHALL BE SLIP RESISTANT. ABRASIVE ELEMENTS.
<br /> 2 0 PLACED PARALLEL TO,AND NOT MORE THAN, 1 INCH FROM THE NOSE OF THE STEP OR LANDING TO ALERT WITHIN A MULTIPLE ACCOMMODATION TOILET FACILITY. ACCESSIBLE ROUTE AND SHALL EXTEND INTO KNEE AND TOE SPACE UNDERNEATH LAVATORY.
<br /> s 0 2. ANY OBSTRUCTION OVER WALKWAYS SHALL HAVE A CLEAR VERTICAL CLEARANCE OF 80 INCHES. AN THE VISUALLY IMPAIRED. THE STRIPE SHALL BE OF A MATERIAL THAT IS AT LEAST AS SLIP RESISTANT AS 6. LAVATORIES SHALL BE MOUNTED WITH A CLEARANCE OF AT LEAST 29 INCHES FROM THE FLOOR TO THE 5. GRAB BARS SHALL NOT ROTATE WITHIN THEIR FITTINGS.
<br /> o OBJECT SHALL NOT PROTRUDE INTO WALKWAY MORE THAN 4 INCHES. THE TREADS OF THE STAIR. BOTTOM OF THE APRON WITH KNEE CLEARANCE UNDER THE FRONT LIP EXTENDING A MINIMUM OF 30 6. GRAB BARS SHALL BE DESIGNED TO SUPPORTA 250 POUND FORCE AT ANY POINT.
<br /> z 3. WALKS,SIDEWALKS,AND PEDESTRIAN WAYS SHALL BE FREE OF GRATING WHENEVER POSSIBLE. GRID SANITARY FACILITIES (GENERAL)
<br /> LU 4. WHERE STAIRS OCCUR OUTSIDE OF A BUILDING,THE UPPER APPROACH AND ALL TREADS SHALL BE 1. ALL DOORWAYS LEADING TO SANITARY FACILITIES SHALL HAVE 32 INCH CLEAR,UNOBSTRUCTED INCHES IN WIDTH WITH 8 INCHES MINIMUM DEPTH AT THE TOP. TOE CLEARANCE SHALL BE THE SAME
<br /> o OPENINGS WITHIN GRATINGS LOCATED IN THE SURFACE OF ANY OF THESE AREAS SHALL BE LIMITED TO MARKED BY A STRIP OF CLEARLY CONTRASTING COLOR AT LEAST 2 INCHES WIDE AND PLACED PARALLEL WIDTH AND MINIMUM OF 9 INCHES HIGH FROM THE FLOOR AND A MINIMUM OF 11 INCHES DEEP FROM THE ADDITIONAL REQUIREMENTS
<br /> LU Lu 112 INCH IN THE DIRECTION OF THE TRAFFIC FLOW. OPENINGS.
<br /> U) TO,AND NOT MORE THAN 1 INCH FROM THE NOSE OF THE STEP OR LANDING TO ALERT THE VISUALLY FRONT OF THE LAVATORY. 1. THE BOTTOM OF RECEPTACLE OUTLET BOXES SHALL BE NOT LESS THAN 15 INCHES ABOVE THE FLOOR
<br /> 4. WHEN THE SLOPE IN THE DIRECTION OF TRAVEL OF ANY WALK EXCEEDS 1 VERTICAL TO 20 HORIZONTAL 2. ALL SINKS,FAUCET CONTROLS,AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE HAND AND
<br /> } IMPAIRED. THE STRIP SHALL BE OF A MATERIAL THAT IS AT LEAST AS SLIP RESISTANT AS THE TREADS OF 7. HOT WATER AND DRAIN PIPES UNDER LAVATORIES SHALL BE INSULATED OR OTHERWISE COVERED. 2. THE ELECTRICAL BOX OF SWITCHES INTENDED TO BE USED BY OCCUPANTS OF A ROOM OR AREA TO
<br /> CO m (5%), IT SHALL COMPLY WITH THE PROVISIONS OF PEDESTRIAN RAMPS. THE STAIR. A PAINTED STRIP SHALL BE ACCEPTABLE. SHALL NOT REQUIRE TIGHT GRASPING,PINCHING,OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO THERE SHALL BE NO SHARP OR ABRASIVE SURFACES UNDER LAVATORIES. CONTROL LIGHTING AND RECEPTACLE OUTLETS,APPLIANCES,OR COOLING,HEATING AND VENTILATING
<br /> a o 5. A LEVEL AREA,2%MAX SLOPE,SHALL BE PROVIDED AT ALL DOORS. REFER TO ENTRANCE NOTES BELOW ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5 LBS. LEVER-OPERATED,PUSH TYPE,AND
<br /> 5. ALL STAIR TREAD SURFACES SHALL BE SLIP RESISTANT. 8. MIRRORS SHALL BE MOUNTED WITH BOTTOM EDGE OF THE REFLECTIVE SURFACE NOT MORE THAN 40 EQUIPMENT,SHALL BE NOT LESS THAN 36 INCHES NOR MORE THAN 48 INCHES(MEASURED TO TOP)
<br /> AND ACCESSIBLE DETAILS FOR CLEAR SPACE REQUIREMENTS. 6. HANDRAILS AT STAIRWAYS SHALL BE 34 INCHES TO 38 INCHES ABOVE THE NOSING OF THE TREADS ELECTRONICALLY CONTROLLED MECHANISMS ARE EXAMPLES OF ACCEPTABLE DESIGNS.
<br /> SELF-CLOSING INCHES FROM THE FLOOR. LOCATE SOAP DISPENSERS,PAPER TOWEL DISPENSERS,SANITARY NAPKIN ABOVE THE FLOOR OR WORKING PLATFORM.
<br /> 0 6. WARNING CURBS,MINIMUM 6 INCHES IN HEIGHT,SHALL BE PROVIDED FOR ANY ABRUPT LEVEL CHANGE VALVES ARE ALLOWED IF THE FAUCET REMAINS OPEN FOR AT LEAST 10 SECONDS.
<br /> MEASURED TO THE TOP OF THE HANDRAIL. 3. LAVATORIES SHALL BE MOUNTED WITH A MINIMUM DISTANCE OF 18 INCHES FROM A WALL OR PARTITION DISPENSERS AND WASTE RECEPTACLES WITH ALL OPERABLE PARTS NOT MORE THAN 40 INCHES FROM 3. THE CENTER OF FIRE ALARM INITIATING DEVICES(BOXES)SHALL BE LOCATED 48 INCHES ABOVE THE
<br /> ADJACENT TO WALKWAYS EXCEPT AT ADJACENT STREET OR DRIVEWAY/PARKING STALL. THE FLOOR. LEVEL OF THE ADJACENT FLOOR,WORKING PLATFORM,GROUND SURFACE,OR SIDEWALK.
<br /> w 0 TO THE CENTER OF THE FIXTURE. ACCESSIBLE LAVATORIES SHALL BE MOUNTED WITH THE FRONT OF THE
<br /> 0 0HIGHER OF THE RIM OR COUNTER SURFACE NO HIGHER THAN 34 INCHES ABOVE THE FLOOR. 9. TOILET TISSUE DISPENSERS SHALL BE LOCATED ON THE WALL 7 INCHES MINIMUM AND 9 INCHES MAXIMUM 4. INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL BE THE STANDARD USED TO IDENTIFY FACILITIES THAT
<br /> ly Q FROM THE FRONT EDGE OF THE TOILET SEAT. THE DISPENSER OUTLET MUST BE BELOW THE GRAB BAR ARE ACCESSIBLE TO AND USABLE BY PHYSICALLY DISABLED PERSONS.
<br /> a co 4. DOORS TO ACCESSIBLE TOILET ROOMS SHALL NOT ENCROACH INTO THE CLEAR FLOOR SPACE REQUIRED AND 19 INCHES MINIMUM ABOVE THE FLOOR. 5. THE SYMBOL,SPECIFIED ABOVE,SHALL CONSIST OF A WHITE FIGURE ON A BLUE BACKGROUND. THE BLUE
<br /> FOR ANY FIXTURE. SHALL BE EQUAL TO COLOR NO 15090 IN FEDERAL STANDARD 595A.
<br /> w �
<br /> 00
<br /> Ww
<br /> UJ
<br /> =o
<br /> ACCESSIBILITY NOTES A
<br /> U X
<br /> LL Z DOOR NOTES: LETTERING
<br /> Uj Q BOTTOM RAIL: RAISE 1132"
<br /> z A. MINIMUM 10"HIGH SMOOTH SURFACE AT DOOR BOTTOM,EITHER ATTACHED PANEL OR BOTTOM RAIL. co
<br /> ATbo 2�1
<br /> DISABLED ACCESSIBILITY NOTES AND DETAILS IN DRAWINGS
<br /> Q Z HARDWARE: AZ ADA-1, ADA-2, AND ADA-3 ARE INTENDED TO SHOW GENERAL
<br /> 0 0 o A. OPENABLE FROM INSIDE WITHOUT USE OF KEY OR SPECIAL KNOWLEDGE OR EFFORT. CORRESPONDING
<br /> Of 0- B. OPENABLE BY SINGLE EFFORT LEVER-TYPE DEVICE(NOT REQUIRING GRASPING)MOUNTED 34"T044"A.F.F. 6" GRADE 2 BRAILLE ACCESSIBLE COMPLIANCE AND NOT ALL NOTES OR DETAILS RECORD DATES
<br /> a� w < < C. MAXIMUM 5 LBS.EFFORT TO OPERATE EXTERIOR DOOR,5 LBS.FOR INTERIOR DOORS. DD SUBMITTAL
<br /> N w Q1 MAX. N 2 INTERNATIONAL SYMBOL ENTRANCE SIGN(PLACED ON EXIT SIGN(PLACED ON MAY BE APPLICABLE TO THIS PROJECT.
<br /> Q1 MAX. N SIGNAGE: BLDG.SUBMITTAL 2/4/2022
<br /> o c m A. MOUNTING LOCATION SHALL BE DETERMINED SO THAT A PERSON MAY APPROACH WITHIN 3 INCHES OF SIGNAGE WITHOUT ENCOUNTERING PROTRUDING OBJECTS OR STANDING WITHIN SWING OF DOOR. OF ACCESSIBILITY EXTERIOR OF BUILDING) INTERIOR OF BUILDING) BID SET
<br /> N w U
<br /> B. IF ACCESSIBILITY OR EXIT SIGN OCCURS ON SIDELITE,PLACE A MATCHING OR BLANK PANEL ON OPPOSITE SIDE. EXIT SIGN NOTES: CONTRACT SET
<br /> C. SIGNS WITH RAISED CHARACTERS AND BRAILLE SHALL BE LOCATED 48 INCHES MINIMUM ABOVE THE FINISH FLOOR OR GROUND SURFACE MEASURED FROM THE BASELINE OF THE LOWEST LINE OF BRAILLE AND 60 LETTERS/NUMERALS SHALL BE RAISED 1/32",UPPER CASE SANS SERIF TYPE ON CLEAR PHOTOPOLYMER REFER TO PROJECT-SPECIFIC PLANS AND SHEETS FOR EXTENT
<br /> z 0 INCHES MAXIMUM MEASURED FROM THE BASELINE OF THE HIGHEST LINE OF RAISED CHARACTERS.
<br /> U) THRESHOLD THRESHOLD PLAQUE AND SHALL BE ACCOMPANIED WITH GRADE 2 BRAILLE. RAISED CHARACTERS SHALL BE AT LEAST OF WORK REQUIRING COMPLIANCE WITH ACCESSIBILITY REVISIONS
<br /> LU CU z z SIDELITE WHERE OCCURS SIDELITE WHERE OCCURS 5/8"HIGH,BUT NO HIGHER THAN 2". REQUIREMENTS.
<br /> CO
<br /> m GRADE 2 BRAILLE STANDARD DIMENSIONS: 0.100"O.C. INTERDOT SPACING
<br /> z o FINISHED FLOOR,EVEN HEIGHT DOT BASE DIAMETER .059"
<br /> a THRESHOLD % / ACCESSIBILITY 3"MIN. \ % / \ ACCESSIBILITY / / \ \ 3"MIN. DOT HEIGHT(ROUNDED ON TOP) 025"
<br /> z Zoo COMPRESSED CARPET, 1/4"MAX BELOW THRESHOLD / ��SIGN ON STRIKE \ / \ SIGN ON STRIKE / \ DOT SPACING WITHIN THE SAME CELL 10"O.C. �o O • 00 • O • O _
<br /> Q o / SIDE OF DOOR, \ / \ SIDE OF DOOR, / \ DOT SPACING BETWEEN CELLS 20"O.C. o O O O O
<br /> = o o z U_ MOUNTED ON z z z MOUNTED ON z z
<br /> 0 0 w / ¢ WALL OR 00 O 0
<br /> \ _ w / \ / _ w WALL OR \ \ / F 0-
<br /> m o 0 Aw o \ z SIDELITE o / o o \ / z SIDELITE \ / o o o • o o • • o o • SEE PROJECT-SPECIFIC PLANS AND SHEETS FOR SPECIFIC
<br /> LU a w w o w • o o • o o DETAILS AS APPLICABLE. 0
<br /> wZ
<br /> 0 0 x " �' II T 11 , 0 0 . 0 .
<br /> z z a 0.059"DIA. o 0"
<br /> aw �
<br /> o Q N zt EXIT SIGN WITH BOTH TACTILE AND EXIT SIGN WITH BOTH TACTILE AND 0.200"O.C.INTERCELL SPACING IN NO CASE ARE REQUIREMENTS ON ADA-1, ADA-2, OR ADA-3 TO Z '
<br /> al w a ALL TACTILE EXIT SIGNS ARE IN ADDITION TO ILLUMINATED EXIT SIGNS. AT WALLS SECURE SIGN WITH VINYL BE OVER-RIDDEN. CLIENT
<br /> rn o 0 BRAILLE LETTERS ON STRIKE SIDE OF BRAILLE LETTERS ON RIGHT SIDE OF
<br /> LU /����������� DOORS ON WALL OR SIDELITE DOORS ON WALL OR SIDELITE FOAM TAPE. AT STOREFRONT LOCATIONS ATTACH SIGN TO GLASS WITH MASTIC CLEAR DOUBLE FACED PRB MANAGEMENT INC
<br /> CD <N TAPE AND BEHIND THE SIGN MOUNT A FROSTED VINYL SHAPE OF SAME CONFIGURATION AS SIGN ON
<br /> NI w 0 TRANSITION BETWEEN FLOOR FINISHES LEVEL CHANGES OUTSIDE VIEW SINGLE DOOR INSIDE VIEW SINGLE DOOR OUTSIDE VIEW PAIR OF DOORS INSIDE VIEW PAIR OF DOORS EXTERIOR FACE OF GLASS TO EXACTLY ALIGN WITH SIGN.
<br /> IIwo
<br /> 4709 Mangels Blvd.
<br /> o z mFairfield,CA 94534
<br /> THRESHOLDS AND TRANSITIONS 3" = 1'-0" 19 ACCESSIBILE ENTRANCES AND SIGNAGE 3/16" = 1'-0" 7 ADDITIONAL NOTE B
<br /> a 0 SITE#:3560
<br /> U Q
<br /> 0 NOTES: TOTAL PARKING SPACES PROVIDED MINIMUM ACCESSIBLE SPACES REQUIRED* ENTITY#:
<br /> ,I => 1. CLEAR SPACES MUST BE �7 1 TO 25 1
<br /> LL LEVEL TO PREVENT �// 26 TO 50 2
<br /> MI o co WHEELCHAIRS FROM 51 TO 75 3 PROJECT
<br /> DOOR WIDTH DOOR WIDTH DOOR WIDTH DOOR WIDTH 76 TO 100 4
<br /> 0 0 o ROLLING WHEN THE TACO BELL
<br /> co co 0 PLUS 36"MIN. PLUS 24"MIN. PLUS 18"MIN. PLUS 24"MIN. 101 TO 150 5
<br /> ¢ OCCUPANT RELEASES THE
<br /> 151 To 200 6 532 WEST HAMMER LN
<br /> co o WHEEL GRIPS TO REACH 4"MIN. 3201 TO 300 01 TO 400 8 STOCKTON, CA. 95210
<br /> Z" FOR THE DOOR. 1/4"PER EXTERIOR N �I, 60 MIN. FPULL SIDE �LILL SIDE rPULL SIDE �ULL SIDE
<br /> E m Z FOOT(1.5%)SLOPE IS I PULL SIDE I I I I 401 TO 500 9 APN#000-000-000
<br /> = in w ALLOWED FOR DRAINAGE. I z z I z z 501 TO 1000 =2%OF TOTAL
<br /> o I �\ 1001 AND OVER 20 + 1 FOR EACH 100,OR
<br /> cn
<br /> a) 0 w 2. WHERE DOORS OPEN 24"MIN.EXTERIOR, �> \r o FRACTION THEREOF,
<br /> L,
<br /> C z 12"MIN. `o `o I `o `o 'FOR EVERY SIX OR FRACTION OF SIX ACCESSIBLE PARKING OVER 1000
<br /> I 0 0 ONTO,BUT NOT INTO A 18"MIN.INTERIOR 18"MIN
<br /> c Z X - 36 MIN. 4"MIN. 24'MIN. SPACES,AT LEAST ONE SHALL BE"VAN ACCESSIBLE".
<br /> o a > CORRIDOR,THE REQUIRED co 48"MIN.
<br /> _ 10
<br /> REQUIRED PARKING C
<br /> o 0 w LEVEL AREA BEYOND THE VESTIBULE
<br /> INTERIOR EXTERIOR ENDEAVOR
<br /> cb F o DOORS MAY BE A MINIMUM � DOOR DOOR
<br /> w OF 48". 24"MIN. o a o a 24"MIN.
<br /> ml o� I *12"MIN.IF DOOR HAS z o m o o m o w z1 "12"MIN.IF DOOR HAS 12"MIN.IF DOOR HAS 5%OF SEATING AND STANDING SPACES AT DINING SURFACES SHALL BE ACCESSIBLE.REFER TO FIXTURE SUCCESSOR M 11/13/2020
<br /> Oaf I I BOTH A LATCH I o o~ a U o a I I a I I BOTH A LATCH BOTH A LATCH PLAN,DWG.A-1.1 FOR DISBURSEMENT OF ACCESSIBLE SEATING.
<br /> rnl o= 18"MIN PUSH SIDE AND A CLOSER z m z 0 z m = 0 I I AND A CLOSER AND A CLOSER
<br /> z J o I 60"MIN. I ¢ i a - i I I TOTAL NUMBER OF SEATS MINIMUM ACCESSIBLE SEATS REQUIRED ACCESSIBILITY
<br /> NC> a = � PUSH SIDE I I 1 TO 20 1
<br /> o I PUSH SIDE _ ¢ _ ¢ _ _ - PUSH SIDE PUSH SIDE ENTRANCE
<br /> 34 CLR.
<br /> - - - - � - - - - � L - - - - J L - - - - J 21 TO 40 2
<br /> a INTERIOR 54"PREFERRED, 54' PREFERRED, 41 TO 60 3
<br /> E z
<br /> 12"MIN.
<br /> 60"MIN. 60"MIN. 48"MIN. 48"MIN. 61 TO 80 4 DETAILS
<br /> ZM 2 D 81 TO 100 5
<br /> z= 101 TO 120 6
<br /> co fr48"MIN. 121 TO 140 7
<br /> a 141 TO 160 8
<br /> co ui
<br /> 161 TO 180 9
<br /> Ui
<br /> Z 181 TO 200 10
<br /> CU 0 o DOORS AT ENTRANCE VESTIBULE RAMP LANDING AT DOOR HINGE-SIDE APPROACHES-ALL DOORS LATCH-SIDE APPROACHES-ALL DOORS FRONT APPROACHES-INTERIOR DOORS FRONT APPROACHES-EXTERIOR DOORS
<br /> co a z
<br /> Q �
<br /> MANEUVERING CLEARANCES AT DOORS 1/4" = 1'-0" g REQUIRED SEATING D
<br />
|