|
REVISIONS
<br /> V LAYER OF INSULATION
<br /> FACTORY INSTALLED IN
<br /> 1.00' END STANDOFF MEETS e Q
<br /> 0° WOUIREMENTS CLEARANCE The Wedel ND-2 with PSP Accessory Is a compensating
<br /> TO COMBUSTIBLE SURFACES, canopy hood rated for all types of cooking equipment.
<br /> The hood shall have the size, shape and performance
<br /> 3 specified on drawings.
<br /> T_ 11'
<br /> R' FLANZ TO Construction shall be type 430 stainless steel, with a NTY
<br /> 1/4` 4• FAS'M TO WALL #3 or #4 polish where exposed. The manufacturer, ETL AM 1
<br /> 014' and NSF shalt determine the Individual component
<br /> ® WRAPPER PAWLS construction. Construction shall be dependent on the
<br /> WALLRRiMnIf
<br /> FIOR structural application to minimize distortion and other E AOL
<br /> defects. All seams, Joints and penetrations of the •
<br /> WRAPPER Eft hood enclosure to the lower outermost perimeter
<br /> that directs and captures grease-laden vapor and
<br /> 541 exhaust gases shall have a liquid-tight continuous
<br /> external weld In accordance with NEPA 96. The hood
<br /> U.L. Listed Recessed Allanson �� shat[ be waft type with a minimum of four connections
<br /> Round LED future and LED Light
<br /> CKWEL for hanger rods. Connectors shall have 9/161 holes `
<br /> ® ❑ ® LNIALLER TO pre-punched in 1 9' x 1 Jd' angle Iron at the factory
<br /> WRAPM VMS&ur KW to allow for hanger rod connection by others.
<br /> SEE DETAIL TO FAMMY VR%Vn
<br /> CKWEL The hood shalt be furnished with U.L. classified fitters,
<br /> supplied In size and u
<br /> �u�4 � pp quantity as required by
<br /> 4` yrs ventliator,
<br /> abine 241 ,4, W Bra= s The filtershalt extend the full length of the hood
<br /> 1/4• r and the filler panels shall not be more than 6' In
<br /> width � LU DRILLED I
<br /> XT*& The hood manufacturer shall supply comptete computer
<br /> generated submittal drawings Including hood sections
<br /> e° view(s) and hood plan view(s). These drawings must be
<br /> FIELD WRAPPER available to the engineer, architect and owner for
<br /> 2 1/4•
<br /> their use In construction, operation and maintenance,
<br /> THAT THE SPECIFIED WALL,, ACTING AS AN END PANEL, t d
<br /> INSTALLER MUST CONFIRM IS INSTALLED SUCH Exhaust collar to be 4' high with V flange. Duct
<br /> C �
<br /> IS MATED TIGHT TO THE CORRECT END OF HOOD TO sizes, CFM and static pressure requirements shalt be
<br /> 341 54, ACHIEVE A REDUCED MINIMUM EXHAUST CFM LISTING,
<br /> NON-COMPLIANCE WILL NULLIFY THE ETL LISTING, as shown on drawings. Static pressure requirements
<br /> shall be precise and accurate air velocity and volume
<br /> VOID THE MANUFACTURER'S WARRANTY, AND }QLD THE Information Shall be accurate within 1-ft Increments •w
<br /> CONTRACTOR LIABLE FOR ANY AND ALL LOSSES, COSTS,
<br /> 20 40 1/4' 40 1/4" AND EXPENSES RELATED TO THE NON--CONFORMANCE OF along the length of the ventilator.
<br /> THE MANUFACTUREWS SPECIFIED INSTRUCTION. THE
<br /> 12' 9' O'No�i,/9° 0.00'011 THAN
<br /> ACTING AS AN END PANEL MUST EXTEND NO LESS
<br /> THAN 20 FROM THE INTERSECTING WALL ON WHICH HOOD U.L. Incandescent light fixtures and globes shall be
<br /> IS MOUNTED AND MUST EXTEND NO LESS THAN 20' UNDER Installed and pre-wired to a junction box. The light
<br /> 10'-1.00° Overall Length
<br /> BOTTOM OF HOOD TO BE ELIGIBLE FOR REDUCED fixtures shall be Installed with a maximum of 4'0'MINIMUM EXHAUST CFM LISTING, spacing on center and allow up to a 100 watt o
<br /> standard light bulb. 0-
<br /> PLAN YI EW
<br /> _ .r Hgod #1 The hood shalt haves
<br /> _ - A double wall Insulated front to eliminate
<br /> condensation and Increase rigidity. The insulation shall U
<br /> have a flexural modulus of 475 EL meet UL 121
<br /> requirements and be In accordance with NFPA 90A and
<br /> 90B.
<br /> or - An Integral front baffle to direct grease laden
<br /> vapors toward the exhaust filter bank.
<br /> - A built-In wiring chase provided for outlets and
<br /> electrical controls on the hood face and shall not
<br /> penetrate the capture area or require an external
<br /> RECESSED ALLANSON ROUND LED chase way,FIXTURE AND - Removable grease cup far easy cleaning, �
<br /> LED LIGHT, 3500 K WARM OUTPUT. Stainless Steel B,acksplash
<br /> 1
<br /> and Si.desplash The hood shalt be ETL Listed as 'Exhaust Hood
<br /> Without Exhaust Damper', NSF Listed and built In
<br /> 13acl�splash is to be manufactured from#3 or #4 accordance with NEPA 96,
<br /> n sh S/S of the same guage and material as the
<br /> (SEE HOOD OPTIONS
<br /> TABLE)
<br /> FIELD WRAPPER NHIGH fihoods. It wili be supplied With Batton strips and The hood shalt be listed for 450°F cooking surfaces
<br /> ' T
<br /> end strips as netted to close all seams and edges. at 150 CFM/f t, 600'17 cooking surfaces at 200 CFM/f t,
<br /> and 700°F cooking surfaces at 250 CFM/ft. The hood
<br /> EXHAUST RISER shall be ETL Listed as 'Exhaust Hood Without Exhaust
<br /> ATTACHING PLATES Damper'.
<br /> HANGING ANGLE SUPPLY RISER VITH
<br /> E HOOD T E VOLUME DAMPER 3/B
<br /> 23,5Y. OPEN STAINLESS
<br /> STEEL PERFORATED PANEL k
<br /> 201 CAPTRATE SOLBatton Stxi DetailSOLD .�
<br /> FILTER VITH H1313K 6'
<br /> 3' INTERNAL STANDOFF 16' — d
<br /> 241 NOK
<br /> 18` S ste esi n Merl-FI-cation (SDV) U
<br /> IT IS THE RESPONSIBILITY If ordered, CAS Service will perf orm a System Design Verif kation (SDV) once alt equipment 4->OF THE ARCHITECT/OWNER TO has had a comptete start up per the Operation and Installation Manual Typically, the SDV will d CU rN,
<br /> ENSURE THAT THE HOOD CLEARANCE
<br /> FROM LIMITED-COMBUSTIBLE be performed after alt Inspections are complete.
<br /> AND COMBUSTIBLE MATERIALS
<br /> IS DV COMPLIANCE WITH i L co
<br /> to
<br /> LOCAL CODE REQUIREMENTS, '
<br /> Any field related discrepancies that are discovered during the SDV will be brought to the
<br /> attention of the general contractor and corresponding trades on site. These Issues d
<br /> will be documented and forwarded to the appropriate sales office, If CAS Service has to N C d
<br /> 48.0; MAX
<br /> GREASE DRAIN resolve a discrepancy that Is a field Issue, the, general contractor will be notified and N d U
<br /> bitted f or the work. Should a return tri be required E
<br /> WITH REMOVABLE CUP � p q due to any field related discrepancy �-
<br /> that cannot be resolved during the SDV, there will be additional trip charges,
<br /> BACKSPLASH 120.110° HIGH
<br /> x 14ao01 LONG 0 UDuring the SDV, CAS Service will address an discrepancyyCD
<br /> y , that is the fault of the W
<br /> �
<br /> manufacturer. Should a return trip be required, the general contractor and appropriate U `0 i--
<br /> sales office will be notified, There will be no additional charges for manufacturer tl� Q
<br /> RIGHT WALL AS END PANEL Qi i s C i"e p a i'l c i e s ,....,
<br /> U
<br /> EQUIPMENT
<br /> BY OTHERS DATE: 1/15/2020
<br /> DWG.#:
<br /> 4161571
<br /> DRAWN
<br /> BY:
<br /> SCALE:
<br /> 3/4
<br /> ""' MODEL 5!9M2-Z_-PSP=FL MASTER DRAWING
<br /> HOW �i1 DEM❑NSTRATI❑NS ARE AVAILABLE AT THE
<br /> CALIFORNIA BAY AREA DISPLAY CENTER
<br /> FOR PRICES AND QUESTIONS, CALL
<br /> GUSTAVO EUSTIS
<br /> REFERENCE JOB# 4151571
<br /> REG9ICCAPT1VFATRE C❑M
<br /> PH❑NEi (415) 956-2200 FAX: (919) 227-5940 SHEET NO.
<br /> CA2
<br />
|