Laserfiche WebLink
HOBARTi HL600 LEGACY+ <br />60-Quart Maximum Heavy-Duty Mixer <br />SPECIFICATIONS <br />Motor: 2.7 HP high torque motor. <br />200-240/50/60/1 - 18.0 Amps <br />200-240/50/60/3 - 10.0 Amps <br />380-460/50/60/3 -6.5 Amps <br />Electrical: 200-240/50/60/1, 200-240/50/60/3 and <br />380-460/50/60/3 - UL Listed. <br />Controls: Magnetic contactor and thermal overload <br />protection. Internally sealed "Start-Stop" and Power <br />Bowl Lift push buttons. Reduced voltage pilot circuit <br />transformer is supplied for 380-460/50/60/3 machines. <br />A 20-minute SmartTimer- is standard. SmartTimer- <br />includes: <br />Automatic Time Recall, which remembers the last <br />time set for each speed. <br />Transmission: A rated 5.4 HP poly-V belt transfers <br />power from motor to input shaft then geared <br />down to desired reduction with a constant gear <br />mesh. Gears and shafts are heat-treated hardened <br />alloy steel along with anti-friction ball bearings. <br />Circulating oil and grease lubricants furnished to all <br />gears and shafts. <br />Speeds Agitator <br />(RPM) <br />Attachment <br />(RPM) <br />Stir 36 71 <br />First 71 138 <br />Second 123 241 <br />Third 206 401 <br />Fourth 362 707 <br />Bowl Guard: Heavy-duty stainless steel wire front and <br />solid rear portion. Front portion of guard rotates easily <br />to add ingredients and install or remove agitator. <br />It detaches in seconds for cleaning in dishwasher or <br />sink. Rear portion of guard can be quickly cleaned in <br />position. Guard must be in closed position before mixer <br />will operate. Bowl support interlock provides further <br />protection. <br />Power Bowl Lift: Powered by an electric motor, the bowl <br />may be raised or lowered by fingertip control through the <br />conveniently located switch. Bowl will remain in position <br />until switch is activated. <br />Stir-on-Lift Feature: Allows the agitator to run in Stir <br />Speed while the mixer bowl is being raised. Once the <br />bowl is in the raised position, the mixer automatically <br />shifts into the preselected speed. <br />Finish: Metallic gray hybrid powder coat finish. <br />Footpads: Neoprene footpads are standard. <br />Attachment Hub: Comes with front-mounted Hobart <br />standard #12 taper attachment hub for use with Hobart <br />#12 size attachments. <br />Attachments and Accessories: <br />The following are available at extra cost: <br />Attachment / Accessory Device It <br />Stainless Steel Bowl BOWL-HL60 <br />Flat Beater BBEATER-HL60 <br />Wing Whip CWHIP-HL60 <br />Wire Whip DWHIP-HL60 <br />"ED" Dough Hook EDDOUGH-HL60 <br />Dough Hook EDOUGH-HL60 <br />"P" Pastry Knife PPASTRY-H L60 <br />"I" Heavy Duty Wire Whip IWIRE-HL60 <br />Bowl Splash Cover (texan) SPLASH-LEX060 <br />Bowl Scraper SCRAPER-HL60 <br />Ingredient Chute CHUTE-HL <br />Bowl Truck TRUCK-HL1486 <br />Bowl Extension Ring EXTEND-SST6OG <br />Deck Plate DECK-LEG60 <br />9" Vegetable Slicer VS9 <br />Meat Chopper Attachment 12TIN-C/EPAN <br />40 Quart Accessories See HL400 spec sheet <br />Plugs and Receptacles: <br />Dependent on local power codes <br />X - Cord and Plus Standard <br />./- Available at specified voltage, no plug and cord required <br />Machine Voltages <br />HL600 / 200-240 380-460 <br />Service Current <br />Requirement <br />if Plug Connected <br />200-240/ <br />50/60/3/1 230/60/3 460/60/3 <br />20 Amp. 20 Amp. 20 Amp. <br />Terminal Designation <br />of Plug <br />3 Pole <br />4 Wire <br />Grounding <br />3 Pole <br />4 Wire <br />Grounding <br />NEMA Plug <br />Configuration L15-20P L16-20P <br />Plug Configuration <br />41) OD <br />Molded Plug on Cord No No <br />Plug - Straight/Angle Straight Straight <br />NEMA Receptable or <br />Connector Configuration L15-20R L16-20R <br />HL600 LEGACY. 60-QUART MAXIMUM HEAVY-DUTY MIXER <br /> Page 3 of 4