WORK PLANS - Laserfiche WebLink

Home Browse Search

floor plan notes: V 1. content included on this exhibit is limited to the architectural scope only-refer to structural exhibits for additional information -structural is not to be implied or otherwise assumed from this exhibit 2. all dimensions to new construction are to face of framing unless otherwise noted m 3. all dimensions to existing construction are to face of finish unless X otherwise noted O D5 4. grid lines are located at the center of walls and/or columns unless O A3.1.0 otherwise noted IrIf 5. although not required in all cases, it is the architect's standard to utilize 518"type"X"gypsum wall board unless otherwise noted 6. moisture resistant gypsum wall board or cement backer board shall be used at all wet locations 7. contractor to verify(E)conditions and dimensions prior to construction Qj WT 8 1 ❑ and notify architect if a conflict exists pull a rc h i to tore, inc. ' 3 8. contractor to coordinate with kitchen equipment consultant for location ' of soda and bar line chase locations w.o. - vc sleeve penetration 3 7 5 2 v i n e y a r d r a d p p r o s E v i l l e a 9 5 7 4 7 � t installed with upper lip at 6"a.f.f. unless otherwise noted by kitchen 9 1 6 7 4 0 3 7 2 6 � , consultant www . pullarchitecture com I9. see food service drawings and plumbing drawings for locations of floor sinks and floor drains V ' ' 1 WT 9 10. refer to accessibility sheets A-0.3.0&A-0.4.0 for additional information Iwith regard to accessibility related issues 11. mechanical, electrical, plumbing, structural, interior finishes, data, and F WT 7 1 other information referencing other disciplines may be included for design intent and/or reference-refer to specific discipline's exhibit for 6 more information-contractor shall notify architect if a conflict of information exists r 12, all concealed combustible spaces shall be draft stopped at 10'-0" r intervals both horizontal and vertical or shall be sprinkled in r f I accordance with NFPA standards O r 13. refer to kitchen equipment consultant drawings for equipment � t I1 WT 11 specification, clearances, rough in openings, backing requirements, CV etc. O N MICHAEJL K Ol. wr 12 1 4 G r _ J 5131! RENEWAL ci ® 0 0 >� 7 ❑ O _O LL I WT 6 1 6 These drawings,designs,sketches ar d ideas,as well as ay and all electronic files are the sole anc exclusive property of"pull architecture". These plans were creat d and developed k y and for the architect's work- Nothing ronU ined or representei on these documents shall be used by anj person,firm or oth tr entity for any purpose without the Piriol mitten consent of 3n authorized and recognized representative of"pull archite ure". The work contained on these drawing and documents a tries WT 5 1 to this project exclusively,and is not to be used for other I rojects A8 whether related,implied or future. I ' A3.1.0 Irevisions: dbate: � : 1 WT3 keynotes P=np -.._. - ❑� 1 provide continuous solid blocking and backing for equipment -- - ` < �❑ attachment per food service requirements where required I 10A 1 WT 1 DB 1 \�� v r 5 \ provide power and data to POS location per tenant requirements i i \❑ (E) mop sink LO 2 \ L_ _J14❑ BOH window per schedule E % E tenant provided die wall &millwork-tenant shall be responsible for D8 anchoring and support and shall provide structural information where required by the AHJ r A2.2.0 6 tenant provided millwork-tenant shall be responsible for anchoring WT 4 and support and shall provide structural information where required s by the AHJ ❑ � r I 1 1 f wr2 note: r r I WT1 t r project: Sunset Sweets 6649 Embarcadero Dr., Ste 103 ti Stockt n, CA 95219 wall types: developed by: WT 1 (E) 2x6 exterior wall F8 A3.2.0 Pellar n Enterpr ses 1520 Main E treet VV r 2 (E) 2x6 interior demising wall D8 A3.20 Redwood City, CA 063 p. 209.951 1551 � 3 (E) 2x6 interior demising wall C8 A3.2.0 www.pellarir,com project no.: H4 (E) 2x6 interior demising wall A8 A3.2.0 A2021 001 WT 5 (E) 2x6 interior demising wall F6 A3.2.0 date: (E) 2x6 interior demising wall D6 A32.0 4.12. 021 WT 7 (E) 2x6 2x6 interior demising wall C6 A3.2.0 designed by: ll A i t 6 2 E ( ) xexterior wall A3.2.0 G C drawn by: >,�g (E) 2x4 interior wall F4 A3.2.0 100 10A hecked by: (N) tenant fabricated die wall D4 A3.2.0 c ASL f 10o r plan wT 106 (N) tenant fabricated die wall C4 A3.2.0 O sheet: 112rr �t-0'r WT 11 (E) 2x6 2x6 interior demising wall A4 A32O.0 4= Al I. CWT 12 (N) 2x4 at 16"o.c interior demising wall F2 A3.2.0