SR0084754 - Laserfiche WebLink

Home Browse Search

Orencoa Control and Alarm Panels. General Installation and Wiring Instructions Before beginning the Installation, read these Iristrucgons thoroughly. Not performing the Installation according to these Instructlons may vold the limited warranty. Follow all applicable electrical codes. Contact your distributor or dealer If there is a difference between these Instructions and any applicable regulations. Inspect your order for completeness and shipment damage; contact your distributor or dealer If something Is missing or damaged. Mount the panel on a post or exterior wall within sight of the tank or basin. IMPORTANT DO NOT mount cof►hnl panels on exterior walls other than garage or shop walls! The motor contactor makes a sound while engaging and disengaging that can be disruptive to residents. Route and connect the electrical conduit or direct -bury cable between the splice box(es), control panel, and service entrance panel, • Orenco recommends a minimum burial depth of 2 ft (0.6 m), • Follow applicable codes goveming conduit or cable bury, • See instruction set ON -CP -GEN -5 (Included with the panel) for Instructions on Installing conduit hubs. Route all wires and cords between the components, splice box(es), control panel(s), and service panels. • Use the schematics and wiring diagrams Included with the panel for specifics, • Use only CU conductors, 60° C (1400 9 minimum, rated for wet locations. • Be sure to pull enough wire or cable into the splice box(es) (6-8 Inches or 150- 200 mm above the splice boo and panel to easily make connections. • Use color -coded or labeled 14 AWG wires between the float switch cords and the panel, a See Table i fir wire sizes for willing between tie pump and pdnial. Undersized wires can drop voltage and negatively affect pump performance. Step 4a: Make sure that all circuit breakers are turned off in the control panel and the service entrance panel. Maidmum distance from the sub -panel to the pump motor for Me recommended wire sae, based on a 3% maximum voltage dmp from the sub -panel to load at the maxlmum recognized pump mokrr amps, and at 167° F (75° Q. Orenco Systems"', Inc., 814 Airway Ave., Sutherlin, OR 97479 USA ■ 800-348-9843 • 541-459-4449 • www.arenco.com EN -CP -GEN -1 Rev.5.0' 10117 Page 1 of 2 Mounting Bracket Motor Breaker Control Max. voltage, Panel E �9i distance, VAG hp 4 x 4 in. Post In ft (100 x 1013 -mm) mrn1 (M? 120 1/2 20 10 Concrete (0.37) (5.26) (32.0) 24,^, 1 & 15 14 1 C (0.37) (2.011) (49.0) 240 3/4 Recommended Panel Mounting Method Maidmum distance from the sub -panel to the pump motor for Me recommended wire sae, based on a 3% maximum voltage dmp from the sub -panel to load at the maxlmum recognized pump mokrr amps, and at 167° F (75° Q. Orenco Systems"', Inc., 814 Airway Ave., Sutherlin, OR 97479 USA ■ 800-348-9843 • 541-459-4449 • www.arenco.com EN -CP -GEN -1 Rev.5.0' 10117 Page 1 of 2 Pump Motor Breaker Wire Max. voltage, size, size, size, distance, VAG hp amp AWG ft mrn1 (M? 120 1/2 20 10 105 (0.37) (5.26) (32.0) 24,^, 1 & 15 14 1 C (0.37) (2.011) (49.0) 240 3/4 20 14 130 (0.55) (2.OB) (39.6)' 240 1 20 12 172 (0.75) (3.31) (52.4) 240 1-1/2 20 12 126 (1.12) (3.31) (3B.4) Maidmum distance from the sub -panel to the pump motor for Me recommended wire sae, based on a 3% maximum voltage dmp from the sub -panel to load at the maxlmum recognized pump mokrr amps, and at 167° F (75° Q. Orenco Systems"', Inc., 814 Airway Ave., Sutherlin, OR 97479 USA ■ 800-348-9843 • 541-459-4449 • www.arenco.com EN -CP -GEN -1 Rev.5.0' 10117 Page 1 of 2