WORK PLANS - Laserfiche WebLink

Home Browse Search

ELECTRICAL CEILING PLAN E1 GENERAL NOTES: 1.PLACEMENT OF LIGHT FIXTURES SHALL BE SET AS DIMENSIONED & AS SCHEDULED. 2. LIGHT FIXTURES SHALL BE SUPPLIED AS SCHEDULED WITH NO EXCEPTIONS. 3.MINIMUM WIRE SIZE SHALL BE NO. 12 COPPER. 4.ALL EMERGENCY AND EXIT LIGHTING SHALL BE WIRED AHEAD OF THE SWITCHING. EMERGENCY LIGHTING SHALL BE ON THE SAME CIRCUITRY AS THE GENERAL LIGHTING IN THE AREA THEY SERVE. EMERGENCY LIGHTING WIRING SHALL BE IDENTIFIED (MARKED) PER CEC 700.9. PROVIDE GENERAL LIGHTING CIRCUITS, WHICH HAVE EMERGENCY LIGHTING CONNECTIONS, WITH LOCK-OUT ON BREAKER. 5. ALL LIGHTING FIXTURES IN FOOD AND BEVERAGE PREP AREA SHALL BE SHATTERPROOF. ELECTRICAL SYMBOLS LIGHTING FIXTURE SCHEDULE LIGHT FIXTURE SCHEDULE NOTES: ELECTRICAL NOTES: a.ALL WORK TO COMPLY WITH THE 2019 CEC. b.ALL EQUIPMENT TO BE LISTED BY A RECOGNIZED TESTING LAB (i.e. U.L., ETC.). c. LIGHT FIXTURES IN CONTACT WITH INSULATION TO BE U.L. LISTED FOR THERMAL BARRIER OR PROVIDE 3" MINIMUM CLEARANCE. d.MOUNT THE FOLLOWING ABOVE FINISHED FLOOR. OUTLETS - 15" TO 48" SWITCHES - 36" TO 48" THERMOSTAT - 36" TO 48" e.ALL PANELS SHALL BE SERIES RATED AND PROPERLY IDENTIFIED PER SECTION 110-22, CEC. f.SEAL CONDUITS THROUGH WALK-IN COOLER/FREEZER PER CEC 300.7(A). ARC FLASH NOTE: CONTRACTOR SHALL PLACE ALL ARC FLASH LABELING REQUIREMENTS AS CALLED OUT IN CEC SECTION 110.16 GROUNDING NOTE: CONTRACTOR SHALL BOND ALL INTERIOR METALLIC PIPING SYSTEMS (e.g. HOT WATER, GAS, FIRE SPRINKLER, ETC) AND EXPOSED STRUCTURAL STEEL PER CEC SECTION 250.104(B) AND (C). LIGHTING CONTROL NOTE: LIGHTING CONTROL ACCEPTANCE REQUIREMENTS PER 130.4. A CERTIFICATE OF ACCEPTANCE LIGHTING CONTROL ACCEPTANCE TO THE ENFORCEMENT AGENCY UNDER SECTION 10-103(a) OF PART 1 FOR: A)LIGHTING CONTROLS NOTE: DEMAND RESPONSE CONTROLS AND AUTOMATIC DAYLIGHT CONTROLS ARE NOT REQUIRED FOR THIS PROJECT. METER DISTRIBUTION PANEL EXISTING BUILDING ONE-LINE KEYED NOTES LIGHTING CONTROLS DIAGRAM HEALTH CODE LIGHTING LEVELS AT LEAST 50 FOOT CANDLES OF LIGHT IS REQUIRED AT A SURFACE WHERE A FOOD EMPLOYEE IS WORKING WITH FOOD OR WORKING WITH UTENSILS AND EQUIPMENT SUCH AS KNIVES, SLICERS, GRINDERS, OR SAWS WHERE EMPLOYEE SAFETY IS A FACTOR. AT LEAST 20 FOOT CANDLES OF LIGHT IS REQUIRED AT A DISTANCE OF 30 INCHES ABOVE THE FLOOR IN AREAS USED FOR WAREWASHING, HANDWASHING, AND EQUIPMENT AND UTENSIL STORAGE, AND IN TOILET ROOMS. AT LEAST 10 FOOT CANDLES OF LIGHT IS REQUIRED AT A DISTANCE OF 30 INCHES ABOVE THE FLOOR IN WALK-IN REFRIGERATION UNITS AND DRY FOOD STORAGE AREAS, AND INSIDE EQUIPMENT SUCH AS REACH-IN REFRIGERATORS. DATE FOR PERMIT & BID 01-25-22 SEAL: PROJECT LOCATION: SHEET NUMBER: REVISION:DATE: CHECKED BY: ISSUE: DRAWN BY: PROJECT NO.: DATE: PROJECT INFORMATION: CLIENT: CONSULTANT: THESE DRAWINGS, IDEAS, SPECIFICATIONS AND DESIGNS ARE EXCLUSIVE PROPERTY OF WINGSTOP RESTAURANTS, INC. NO PART OF THESE DRAWINGS MAY BE COPIED, REPRODUCED, OR OTHER STRUCTURES BUILT FROM SUCH WITHOUT THE WRITTEN CONSENT OF WINGSTOP RESTAURANTS, INC. COPYRIGHT R 2022 WINGSTOP RESTAURANTS, INC. ALL RIGHTS RESERVED 15505 WRIGHT BROTHERS DRIVE ADDISON, TX 75001 TELEPHONE: (972) 686-6500 FAX: (972) 686-6502 DISCLAIMER: STOCKTON, CA 2021-0486STORE NUMBER: GL#Z060GILL GROVE1687 N CALIFORNIA STREET SUITE #TBDSTOCKTON, CA 95204JJV DRC 2/3/22 796 Merus CourtSt. Louis, MO 63026T 636.349.1600F 636.349.1730DIMMER/SWITCH ELEVATION