|
ti
<br />CALGREEN
<br />2016 CALIFORNIA GREEN BUILDING CODE
<br />THIS PROJECT IS SUBJECT TO THE MANDATORY MEASURES OF THE "CALGREEN" CODE; SEE SHEET CG1 & OTHER SHEETS THAT
<br />REPLACE CODE SECTIONS. ALL FACTORS OF WORK ARE AFFECTED .
<br />- BELOW IS ONLY A PARTIAL LIST:
<br />BUILDING CONSTRUCTION: THE FOLLOWING ITEMS ARE TO BE INCLUDED IN CONSTRUCTION:
<br />+++ RECYCLE 100% OF ALL SITE CONCRETE OR ASPHALT PAVING BEING DEMOLISHED INCLUDING 100% OF ALL SOIL, LANDSCAPE
<br />DEBRIS & OTHER SITE DEBRIS
<br />+++ RECYCLE MIN. 75% OF BUILDING CONCRETE OR CMU WASTE. (SEE SITE PLAN FOR ANY HIGHER REQUIREMENTS)
<br />+++ RECYCLE MIN. 75% BUILDING CONSTRUCTION WASTE INCLUDING WOOD, STEEL, ALUMINUM, GLASS, AND CLEAN
<br />PAPERICARDBOARD (INCLUDE TRASH). (SEE SITE PLAN FOR ANY HIGHER REQUIREMENTS)
<br />+++ PERCENTAGE ARE IN "VOLUME"
<br />+++ WHERE REQUIRED BY LOCAL AGENCIES, INCREASED RECYCLE PERCENTAGE SHALL GOVERN.
<br />+++ ULTRA LOW WATER CLOSET AND URINAL FLUSH VALVES (ZURIN).
<br />+++ 50% SHADING OF EXTERIOR PAVED AREAS IN 15 YEARS.
<br />+++ MOTION SENSOR/CONTROLS FOR RESTROOMS AND STORAGE AREAS.
<br />+++ ADHESIVES AND PAINTS WITH LOW VOC (SEE BELOW).
<br />+++ CEILING TILES WITH RECYCLED CONTENT AND HIGHER REFLECTIVITY (SEE BELOW).
<br />SITE BICYCLE PARKING:
<br />OPERATOR OPTIONS: THE FOLLOWING "GREEN BUILDING" ITEMS ARE AT OWNER'S OPTION TO INCLUDE IN BUILDING: (THESE ARE
<br />IMPORTANT "GREEN" ITEMS; PM TO CLEAR WITH OPERATOR):
<br />+++ RECYCLE OIL.
<br />+++ ELECTRONIC CONTROLLED FIXTURES.
<br />+++ RECYCLE CONTENT IN FURNITURE/DECOR.
<br />+++ ENERGY MANAGEMENT SYSTEM.
<br />SPECIFICATIONS: SEE ALSO, CALGREENS SHEETS SA3 & CG1
<br />ADHESIVE:
<br />ADHESIVES MUST MEET OR EXCEED THE VOC LIMITS OF SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT RULE #1168 BY, AND
<br />ALL SEALANTS USED ASA FILLER MUST MEET OR EXCEED BY AREA AIR QUALITY MANAGEMENT DISTRICT REG. 8, RULE 51. SEE
<br />ALSO CGI
<br />PAINT SPECIFICATIONS:
<br />- WHERE PRACTICAL; PRODUCTS SHALL HAVE OVER 40% EXTRACTED, PROCESSED (WHERE PRACTICAL, AND MANUFACTURED
<br />WITHIN 5DO MILE RADIUS OF PRODUCT SITE). SEE ALSO CGI
<br />-INTERIOR PAINTS: MEET CRITERIA FOR U.S. GREEN BUILDING COUNCIL LEED VERSION 2.2 EQ CREDIT 4.2: LOW EMITTING
<br />MATERIALS: PAINTS AND COATINGS. SEE ALSO CGI
<br />-EXTERIOR PRODUCTS MEET GREEN SEAL GS -11 AND GREEN SEAL GS -03. SEE ALSO A2
<br />CEILING SPECIFICATIONS:
<br />- PRODUCTS SHALL HAVE OVER 45% EXTRACTED, PROCESSED (WHERE PRACTICAL, AND MANUFACTURED WITHIN 500 MILE RADIUS
<br />OF PRODUCT SITE).
<br />- "RECYCLE CONTENT" OF NEW TILE MUST EXCEED 45%.
<br />- LIGHT REFLECTANCE (LEED RC VALUE): EXCEED 45%.
<br />FIRE PROTECTION SYSTEM REQUIREMENTS:
<br />1. NOTICE TO CONTRACTORS: THE FIRE DEPARTMENT DOES NOT ALLOW INSTALLATION OF FIRE ALARM SYSTEMS OR
<br />OTHER FIRE PROTECTION PRIOR TO PLAN APPROVAL. CONTRACTORS WHO ENGAGE IN SUCH ACTIVITIES MAY BE
<br />CITED AND THE PROJECT WILL BE TAGGED.
<br />2 ALL FIRE ALARM SYSTEMS(WHEN APPLICABLE) AND COMMERCIAL HOOD AND DUCT SYSTEMS REQUIRE SEPARATE PLANS
<br />APPLICATION, REVIEW, PERMIT AND FEE. ANY OF THE ABOVE NAMED SYSTEMS INCLUDED WITH THIS APPLICATION AND
<br />SHOWN OR NOTED ON THESE PLANS ARE TO BE USED FOR BID PURPOSES ONLY FOR FIRE DEPARTMENT APPROVAL OF
<br />THE ABOVE NAMED APPLICATION DOES NOT INCLUDE ANY OF THE ABOVE SYSTEMS. AN AUTOMATIC FIRE EXTINGUISHING
<br />AND ALL HOOD DUCT, PLENUM AND
<br />SYSTEM IS REQUIRED FOR THE PROTECTION OF COMMERCIAL COOKING EQUIPMENT,
<br />COOKING SURFACES. SUBMIT PLANS TO FIRE DEPT, FOR REVIEW, APPROVAL & PERMITTING
<br />3. APPROVED NUMBERS AND OR LETTERS SHALL BE PLACED ON ALL BUILDINGS TO BE VISIBLE FROM THE
<br />STREET.
<br />4. PROVIDE A "KNOX BOX" SECURITY KEY BOX AT AN APPROVED ACCESSIBLE LOCATION (6' ELEVATION).
<br />COORDINATE WITH FIRE DEPARTMENT FOR EXACT LOCATION. PROVIDE KEYS WITH IDENTIFICATION
<br />TAGS.
<br />5. SEPARATE PERMIT IS REQUIRED FOR ANSUL SYSTEM TO BE TESTED AND APPROVED BY PLUMBING
<br />DEPARTMENT.
<br />6. INSPECTIONS ARE TO BE REQUESTED THROUGH THE BUILDING DIVISION WISPECIFIC INSPECTION.
<br />7. ADDRESS NUMBERS SHALL BE INSTALLED ON THE FRONT OR PRIMARY ENTRANCE FOR ALL BUILDINGS. MINIMUM
<br />E R TENANT PACE
<br />ADDRESS O S
<br />MULTIPLE ACCESS ISPROVIDED,
<br />SIZE SHALL BE 12" HIGH BY 1" STROKE. WHERE U
<br />NUMBER SHALL BE PROVIDED ON EACH MAN DOOR. ADDRESS NUMBERS TO BE ILLUMINATED AT NIGHT.
<br />8. RANGE HOODS, DUCTS, GRILLS, AND FRYERS IN COMMERCIAL KITCHENS SHALL BE EQUIPPED WITH AN APPROVED
<br />AUTOMATIC WET CHEMICAL SYSTEM. SETS OF PLANS AND SPECIFICATIONS SHALL BE SUBMITTED TO THE DIXON
<br />FIRE DEPARTMENT FOR REVIEW AND APPROVAL. SYSTEMS SHALL BE EQUIPPED WITH AUTOMATIC GAS AND
<br />ELECTRIC SHUT-OFF, THE LATEST EDITION OF N.F.P.A. 2013, "STANDARD FOR INSTALLATION OF EQUIPMENT FOR
<br />REMOVAL OF SMOKE AND GREASE -LADEN VAPORS FROM COMMERCIAL COOKING EQUIPMENT" SHALL BE
<br />CONSIDERED AS A GUIDE TO RECOMMENDED GOOD PRACTICE, AN APPROVED WET CHEMICAL FIRE
<br />EXTINGUISHER HAVING A UL K -RATING SHALL BE MOUNTED IN THE KITCHEN. WITH (2) TWO 2A10BC FIRE
<br />EXTINGUISHERS. NO CONSTRUCTION ABOVE THE SLAB SHALL OCCUR UNTIL STREETS OR ACCESS WAYS ARE
<br />PAVED. REFER TO PLUMBING AND MECHANICAL DEPARTMENT FOR INSTALLATION OF HOOD AND VENT
<br />SUPPRESSION SYSTEMS.
<br />9. UNDERGROUND UTILITIES ARE INSTALLED AND REQUIRED FIRE HYDRANTS ARE INSTALLED AND TESTED. OPTION:
<br />CONSTRUCTION ABOVE THE SLAB IS PERMITTED PRIOR TO THE PAVED STREETS AND/OR ACCESS WAYS AND
<br />INSTALLATION OF UNDERGROUND UTILITIES IF A FEE MAY BE REQUIRED AND SHALL BE PAID INTO THE FIRE
<br />DEPARTMENT CAPITAL EQUIPMENT REPLACEMENT AND REPAIR FUND. THIS FEE SHALL BE PAYABLE AT THE TIME
<br />OF BUILDING PERMIT ISSUANCE. PORTABLE FIRE EXTINGUISHER(S) SHALL BE PROVIDED AND INSTALLED IN
<br />ACCORDANCE WITH THE MOST CURRENT EDITION OF CBC.
<br />10. CALIFORNIA FIRE CODE AND FIRE CODE STANDARD NUMBER 10-1. MINIMUM APPROVED SIZE FOR ALL PORTABLE
<br />FIRE EXTINGUISHERS SHALL BE 2A 10B:C. PER STOCKTON CITY ORD. TEMPORARY OFFICE
<br />CONSTRUCTION/MODULAR BUILDINGS SHALL HAVE THE FOLLOWING REQUIREMENTS: A. PROVIDE "K" GLASS FIRE
<br />EXTINGUISHER IN A READILY ACCESSIBLY LOCATION ADJACENT TO THE PRIMARY EXIT TO THE
<br />UNIT(S)/MODULAR(S), PROVIDE A MINIMUM OF ONE BATTERY-OPERATED SMOKE DETECTOR. WHEN THE UNIT IS
<br />BROKEN UP INTO MULTIPLE SPACES SUCH AS OFFICE(S) AND STORAGE AREA(S). B. A SMOKE DETECTOR SHALL
<br />BE INSTALLED IN EACH AREA. A MINIMUM 48-HOUR NOTICE IS REQUIRED FOR FIRE DEPARTMENT WITNESSING OF
<br />ALL NECESSARY TESTS AND/OR INSPECTIONS. C. PROVIDE ONE CLASS "K" FIRE EXTINGUISHER AT KITCHEN AREA.
<br />13. SUBMIT PLANS TO AND OBTAIN PERMIT FROM FIRE PREVENTION WORK.
<br />14. CALIFORNIA LICENSED C-16 CONTRACTOR SHALL NOTIFY THE FIRE DEPARTMENT WHEN THEY WILL TEST
<br />PLUMBING AND ANSUL SYSTEM, SO THAT THE FIRE DEPARTMENT WILL BE ABLE TO ATTEND THE TEST.
<br />15. FIRE HYDRANTS SHALL BE TESTED AND APPROVED, FIRE ACCESS ROADS MADE SERVICEABLE PRIOR TO
<br />DELIVERY OF COMBUSTIBLE MATERIALS ON SITE. ALL CONSTRUCTION WORK IS SUBJECT TO STOP WORK ORDER
<br />IF ACCESS ROADS BECOME IMPASSABLE OR FIRE HYDRANT INOPERABLE. SEE THE BACK OF THE BUILDING &
<br />SAFETY DIVISION PERMIT CARD FOR FIRE PRODUCTION REQUIREMENTS DURING CONSTRUCTION.
<br />16. WHEN FIRE FACILITIES SUCH AS, BUT NOT LIMITED TO, FIRE HYDRANTS AND ACCESS ROADS ARE TO BE
<br />INSTALLED BY THE DEVELOPER, THEY SHALL BE INSTALLED AND MADE SERVICEABLE PRIOR TO AND DURING THE
<br />TIME OF CONSTRUCTION (SECTION 901.3 CFC)
<br />17. OBTAIN PERMIT FROM THE FIRE PREVENTION DIVISION FOR FIRE SPRINKLER ALARM SUPERVISION. SUPERVISION
<br />IS REQUIRED ON ALL FIRE SPRINKLER SYSTEMS WITH 20 OR MORE SPRINKLER HEAD. CFC 903.4. PLANS FOR FIRE
<br />ALARM SYSTEM SHALL BE SUBMITTED TO THE CITY/COUNTY FIRE DEPARTMENT FOR REVIEW AND APPROVAL.
<br />18. THE GENERAL CONTRACTOR AND THE SPRINKLER CONTRACTOR SHALL COORDINATE THE PROTECTION OF ROOF
<br />"CRICKETS" (WHERE APPLICABLE).
<br />19. SEE ADDITIONAL FIRE SPRINKLER NOTES ON SHEET SA5
<br />20. LOCATE TYPE "K" EXTINGUISHER W/ IN 18' OF HOOD. ADD CONSPICUOUS PLACARD NEAR IF @ TO READ; "THE FIRE
<br />SPRINKLER SYSTEM SHALL BE ACTIVATED PRIOR TO USING THE PORTABLE FIRE EXTINGUISHER" (WHEN APPLICABLE)
<br />21, SUBMIT PLANS TO AND OBTAIN PERMIT FROM THE FIRE PREVENTION DIVISION FOR THE INSTALLATION OR MODIFICATION
<br />OF FIRE SPRINKLER SYSTEM. INSTALLATIONS MUST ALSO COMPLY WITH FFD POLICY SECTION 405. FFD POLICIES CAN BE
<br />FOUND ON THE FIRE DEPARTMENT WEBPAGE UNDER FIRE PREVENTION & INVESTIGATION, FIRE DEPARTMENT POLICIES.
<br />22. OBTAIN PERMIT FROM THE FIRE PREVENTION DIVISION (OVER THE COUNTER) FOR FIRE SPRINKLER ALARM SUPERVISION.
<br />SUPERVISION IS REQUIRED ON ALL FIRE SPRINKLER SYSTEMS WITH 20 OR MORE SPRINKLER HEADS. 2016 CFC, SECTION
<br />903.4 INSTALLATIONS MUST ALSO COMPLY WITH FFD POLICY SECTIONS 405 AND 407. FFD POLICIES CAN BE FOUND ON
<br />THE FIRE DEPARTMENT WEBPAGE UNDER FIRE PREVENTION & INVESTIGATION. FIRE DEPARTMENT POLICIES.
<br />GENERAL NOTES:
<br />1. ALL WELDING SHALL BE INSPECTED BY AN APPROVED TESTING AGENCY IN ACCORDANCE W/ CBC SECTION
<br />1705.2.2.1 SUBMIT REPORTS TO THE DEVELOPMENT DEPARTMENT, BUILDING AND SAFETY DIVISION. ALL SPECIAL
<br />INSPECTIONS REQUIRED IN SEC. 1704 & 1705 NEED TO BE INCLUDED IN THE SPECIAL INSPECTION & TESTING FORM.
<br />ANY WORK DONE IN THE FIELD NEED A FIELD INSPECTION & REPORT FROM TESTING SHOULD BE SENT TO
<br />BUILDING SERVICES DIVISION.. UBC ALSO REQUIRES MILUSHOP CERTIFICATION (OR ICBO EVALUATION SERVICE
<br />NUMBER) IF ANY WORK IS DONE IN A SHOP; THE CERTIFICATION MUST BE ISSUED BY AN APPROVED AGENCY.
<br />2. ALL HIGH-STRENGTH BOLTING SHALL BE INSPECTED BY AN APPROVED INSPECTION AGENCY IN ACCORDANCE W/
<br />CBC SECTION 1705A.2.1 SUBMIT REPORTS TO THE DEVELOPMENT DEP., BUILDING AND SAFETY DIVISION.
<br />3. A PROPOSAL FOR SPECIAL INSPECTION IS REQUIRED TO BE SUBMITTED PRIOR TO ISSUANCE OF PERMITS, THE
<br />PROPOSAL MUST: 1) IDENTIFY THE SCOPE OF REQUIRED INSPECTIONS, 2) IDENTIFY THE APPROVED INSPECTION
<br />FIRM & INDIVIDUAL(S) PERFORMING THE INSPECTIONS, 3) SPECIFY THAT ALL INSPECTIONS MUST BE AS PER
<br />BUILDING DEPARTMENT APPROVED PLANS, NOT SHOP DRAWINGS. THE FOLLOWING SPECIAL INSPECTIONS ARE
<br />REQUIRED FOR THIS PROJECT: a) CONCRETE: fc= IF OVER 2500 PSI, SPECIFY ON PLANS. b) FIELD AND SHOP
<br />WELDING (DEFINE AS APPLICABLE) c) HIGH STRENGTH BOLTING d) OBSERVATION OF SOIL EXCAVATION &
<br />FOUNDATION CONSTRUCTION OPERATIONS BY A REPRESENTATIVE OF THE GEOTECHNICAL FIRM IDENTIFIED
<br />BELOW:
<br />4. ALL DECORATIVE MATERIALS MUST BE FIRE
<br />RETARDANT.
<br />5, ALL DUCT WORK SHALL BE CONSTRUCTED, ERECTED AND TESTED IN ACCORDANCE WITH THE MOST RESTRICTIVE
<br />OF ASHRAE, SMACNA AND THE CALIFORNIA CODE.
<br />6. MECHANICAL CONTRACTOR SHALL PROCURE THE SERVICES FOR THE RECOGNIZED TEST AND BALANCE AGENCY
<br />WHICH SPECIALIZES IN TESTING AND BALANCING OF HVAC SYSTEMS RESULTS SHALL BE SUBMITTED TO THE
<br />ARCHITECT, ENGINEER AND BUILDING SERVICES DIVISION FOR REVIEW.
<br />7. SOILS ENGINEER TO OBSERVE GRADING & EXCAVATION AND SUBMIT TESTING REPORTS TO THE BUILDING
<br />DEPT. PER THE SOILS REPORTS.
<br />8. GENERAL CONTRACTOR SHALL CHECK AND VERIFY ALL DIMENSIONS OF BUILDING AND SITE AND REPORT ANY
<br />DISCREPANCIES TO THE OWNER OR ARCHITECT BEFORE SUBMITTING BIDS OR BEGINNING WORK. THE
<br />CONTRACTOR SHALL ALSO VERIFY ALL UTILITY LOCATIONS AND DEPTHS AS INDICATED HEREON AND SHALL BE
<br />RESPONSIBLE FOR REPORTING ANY DISCREPANCIES BETWEEN THESE PLANS AND EXISTING CONDITIONS PRIOR TO
<br />SUBMITTAL OF BID OR BEGINNING WORK. EACH CONTRACTOR SHALL BE RESPONSIBLE FOR SUBMITTING AND
<br />OBTAINING THEIR RESPECTIVE CONSTRUCTION PERMITS ARRANGING GOVERNMENTAL INSPECTIONS AND
<br />APPROVALS.
<br />9. ANY CONSTRUCTION ON STATE HIGHWAYS MUST CONFORM TO BOTH LOCAL JURISDICTION AND STATE
<br />DIVISION OF HIGHWAYS SPECS. OBTAIN AN ENCROACHMENT PERMIT FROM THE CAL TRANS OFFICE 1352 W,
<br />OLIVE AVE. PRIOR TO ANY WORK OFF SITE.
<br />10. ANY CONSTRUCTION OUTSIDE OF PROPERTY INCLUDING UTILITIES, PAVING CURBS, AND EARTHWORK MUST MEET
<br />ALL PERTINENT AND APPLICABLE SPECIFICATIONS AND STANDARDS OF AND SHALL BE INSPECTED AND APPROVED
<br />BY CITY/COUNTY, STATE AND/OR LEGAL REPRESENTATIVE OF THE CITY/COUNTY.
<br />11. REPAIR ALL DAMAGED AND/OR OFF GRADE OFF-SITE CONCRETE IMPROVEMENTS AS DETERMINED BY THE
<br />CONSTRUCTION MANAGEMENT DIVISION OF THE GOVERNING REGULATORYAGENCY(S).
<br />12. ANY SURVEY MONUMENTS WITHIN T4 AREA OF CONSTRUCTION SHALL BE PRESERVED OR RESET BY A REGISTERED
<br />CIVIL ENGINEER OR A LICENSED LAND SURVEYOR.
<br />13. ALL SIGN PROPOSALS TO BE SUBMITTED TO PLANNING DEPARTMENT OF GOVERNING JURISDICTION PRIOR TO
<br />INSTALLATION FOR VERIFICATION OF COMPLIANCE WITH ZONING ORDINANCES. SEPARATE SITE PLAN REVIEW
<br />REQUIRED. SIGNAGE UNDER SEPARATE CONTROL BY OWNER.
<br />14. THE CONSTRUCTION OF ANY OVERHEAD IN THE RIGHT OF WAY IS PROHIBITED UNLESS AN ENCROACHMENT
<br />PERMIT IS ISSUED FOR THE SPECIFIC USE. ENCROACHMENT PERMITS MUST BE APPROVED PRIOR TO ISSUANCE OF
<br />BUILDING PERMITS.
<br />15. CODES AND REGULATIONS: THE MOST CURRENT AND RECENT EDITIONS AND CODES, STANDARDS, AND
<br />REGULATIONS ADOPTED BY CITY/COUNTY SHALL GOVERN THE WORK OF THESE DRAWINGS AND SPECIFICATIONS;
<br />THE MOST CURRENT CBG & CFC. SHALL GOVERN INCLUDING ALL RELATED TRADE CODES.
<br />16. DISABLED ACCESS REQUIREMENTS: BUILDING/SITE ACCESS, SIGNAGE, DOORS, HARDWARE, DRINKING FOUNTAINS
<br />TOILET ROOM ACCESSORIES, AND ALL OTHER APPLICABLE MATERIAL SYSTEMS, FIXTURES, FURNITURE, FINISHES,
<br />CONSTRUCTION AND LOCATIONS SHALL FULLY COMPLY WITH THE MOST RECENT EDITIONS OF THE CITY/COUNTY,
<br />AND STATE OF CALIFORNIA "ARCHITECTURAL BARRIERS LAW CAL/ABL" RULES AND REGULATIONS, ,
<br />AS WELL AS
<br />CURRENT FEDERAL "ACCESSIBILITY" REQUIREMENTS AND REGULATIONS.
<br />17. ADA:AMERICAN DISABILITY ACT: THIS PROJECT IN ITS ENTIRETY HAS BEEN DESIGNED TO ANTICIPATE ALL
<br />REQUIREMENTS OF THE ADA STDS. & THE CBC CODE. INTERPRETATIONS WHERE NECESSARY OR
<br />THE PRIOR T PROCEEDING.
<br />UNCLEAR SHALL BE BROUGHT TO THE ATTENTION OF ARCHITECT O O
<br />18. STATE ENERGY REGULATORY: ALL MATERIALS, PRODUCTS, PRODUCT ASSEMBLIES, AND OTHER BUILT-UP OR
<br />INDIVIDUAL COMPONENTS OF THE WORK SHALL FULLY MEET AND COMPLY WITH ALL APPLICABLE CODES AND
<br />SECTIONS OF THE STATE OF CALIFORNIA ENERGY CODES AND REGULATIONS FOR NONRESIDENTIAL BUILDINGS.
<br />19. TYPICAL DETAILS: SEE TYPICAL DETAIL SHEET WHICH DESCRIBES ALL TYPICAL DETAILS FOR STANDARD
<br />NON -TYPICAL STANDARD DETAILS AS APPLICABLE TO SPECIFIC OR GENERAL CONDITIONS.
<br />20. CERTIFICATION OF CONSTRUCTION COMPLIANCE: AT TIME OF REQUEST FOR FINAL INSPECTION OF
<br />CERTIFICATION OF CONSTRUCTION COMPLIANCE MUST BE SUBMITTED TO THE THE CITY/COUNTY BY THE
<br />CONTRACTOR INDICATING THAT ALL WORK DONE AND ALL MATERIALS OF APPLICABLE FEDERAL, STATE AND
<br />LOCAL CODES AND REGULATIONS. CONTRACTOR SHALL ALSO FILE A WRITTEN CERTIFICATE OF COMPLIANCE
<br />WITH REQUIRED APPLICATIONS OF THE CALIFORNIA ENERGY CONSERVATION STANDARDS FOR
<br />NONRESIDENTIAL BUILDINGS. THIS REPORT SHALL INDICATE, BASED ON PERSONAL KNOWLEDGE, THAT THE
<br />WORK APPEARS TO HAVE BEEN PERFORMED IN COMPLIANCE WITH THE APPROVED PLANS AND SPECIFICATIONS.
<br />21. EVERY EXIT DOOR SHALL BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR ANY SPECIAL
<br />KNOWLEDGE OR EFFORT. FLUSH BOLTS OR SURFACE BOLTS ARE PROHIBITED. SPECIAL LOCKING DEVICES
<br />SHALL BE OF AN APPROVED TYPE AND WHEN PERMITTED WITH DOOR SHALL BE IDENTIFIED WITH A VISIBLE SIGN
<br />ABOVE THE DOOR HAVING NOT LESS THAN 1" HIGH LETTERS, STATING "THIS DOOR TO REMAIN UNLOCKED WHEN
<br />BUILDING IS OCCUPIED ".
<br />22. ALL GLAZING WITHIN T-0" OF DOORS: (C.B.C. SECTIONS 1405.13, 1710.5, & 2406) (EXCEPT WHERE INTERRUPTED BY
<br />AN INTERIOR WALL THAT IS PERPENDICULAR TO THE GLAZED WALL) AND ALL GLAZING WITHIN Z -O" OF DOORS
<br />SHALL BE FULL HEIGHT TEMPERED GLASS. ALL GLAZING ADJACENT TO EXTERIOR WALKS (EXCEPT WHERE
<br />INTERRUPTED BY AN INTERMEDIATE HORIZONTAL RAIL AT+24" TO +36" ABOVE THE FLOOR OR WHERE THE SILL IS
<br />+18" MINIMUM ABOVE THE FLOOR) SHALL BE FULL HEIGHT TEMPERED GLASS WHERE THERE IS 9 S.F. OR LARGER
<br />PER LITE. ALL DOOR GLASS AND GLAZING AND ALL WINDOW, SHOWER STALL DOORS, AND MIRROR GLASS AND
<br />GLAZING SHALL FULLY MEET AND COMPLY WITH THE MOST RECENT EDITION OF THE C.B.C. STANDARDS AND ALL
<br />RECENT AND APPLICABLE FEDERAL AND STATE STANDARDS FOR GLASS AND GLAZING. ALL GLAZING SHALL
<br />CONFORM TO THE U.S. PRODUCT SAFETY COMMISSION'S "SAFETY STANDARDS FOR ARCHITECTURAL MATERIALS"
<br />(16CFR1201).
<br />23. EXIT SIGNAGE: ALL EXIT SIGNAGE AS INDICATED ON THE DRAWINGS AND SPECIFIED SHALL BE POSTED AS
<br />DIRECTED AND APPROVED BY AN AUTHORIZED REPRESENTATIVE OF THE CITY/COUNTY AT TIME OF INTERIOR
<br />IMPROVEMENTS, OR BEFORE OCCUPANCY PERMITS ARE ISSUED. EXIT SIGNS & LIGHTING SHALL CONFORM TO CBC
<br />& IBC. WHERE REQ. INSTALL 6" H. ILLUMINATED "EXIT" SIGNS @ EXITS.
<br />24. ROOM CAPACITY SIGNS SHALL BE INSTALLED BY THE OWNER AS REQUIRED AND DIRECTED BY THE BUILDING AND
<br />FIRE DEPARTMENTS.
<br />25. ALL CRACKS AND BUILDING ENVELOPE PENETRATIONS MUST BE CAULKED GASKETED OR 156
<br />WEATHER-STRIPPED TO LIMIT AIR LEAKAGE.
<br />26. INTERIOR FINISHES AND FLAME PROOFING SHALL CONFORM TO WITH CHAPTER 8 OF THE CBC.
<br />27. INTERIOR WALL AND CEILING FINISHES FOR EXIT CORRIDORS SHALL NOT EXCEED AN END POINT FLAME
<br />SPREAD RATING OF 25 FOR ENCLOSED VERTICAL EXIT WAYS AND 75 FOR OTHER EXIT WAYS.
<br />28. EXCAVATION ENCROACHMENT PERMITS ARE REQUIRED FOR ALL WORK DONE IN THE CITY RIGHT-OF-WAY.
<br />29. SEE BUILDING INFORMATION ON THIS SHEET FOR LIST OF SPECIAL INSPECTIONS PER CBC.
<br />30. ALL MECHANICAL EQUIPMENT SHALL BE ADEQUATELY SCREENED TO PREVENT VISIBILITY FROM STREET.
<br />31, COMBUSTIBLE DEBRIS, RUBBISH AND WASTE MATERIAL SHALL NOT ACCUMULATED WITHIN BUILDINGS. RUBBISH
<br />AND WASTE MATERIAL SHALL BE REMOVED AS OFTEN AS PRACTICAL
<br />32. PER CBC SECTION 1704 EACH CONTRACTOR RESPONSIBLE FOR THE CONSTRUCTION OF A MAIN WIND OR
<br />SEISMIC FORCE RESISTING SYSTEM LISTED IN THE STATEMENT OF SPECIAL INSPECTIONS SHALL SUBMIT A
<br />WRITTEN STATEMENT OF RESPONSIBILITY TO THE BUILDING OFFICIAL, THE OWNER PRIOR TO COMMENCEMENT
<br />OF WORK & SHALL CONTAIN ACKNOWLEDGEMENT OF AWARENESS OF THE SPECIAL REQUIREMENTS STATED IN
<br />THE SPECIAL INSPECTIONS.
<br />GENERAL NOTES:
<br />DRAWINGS AND SPECIFICATIONS:
<br />EACH BIDDER/CONTRACTOR SHALL THOROUGHLY EXAMINE ALL DOCUMENTS AND CONDITIONS PRIOR TO BID AND
<br />START OF WORK. THESE DOCUMENTS CONSTITUTE THE CONTRACT DOCUMENTS DESCRIBING THE GENERAL DESIGN
<br />AND CHARACTERISTICS OF THE PROJECT. WHEN THESE DOCUMENTS ARE VAGUE OR CONTRADICTORY, IN PART OR
<br />IN WHOLE, THE CONTRACTOR SHALL BE OBLIGATED TO PROVIDE THE MOST STRINGENT WRITTEN OR DRAWN
<br />INTERPRETATION, HE SHALL BE RESPONSIBLE TO AND LIABLE FOR CORRECTING OR COMPLETELY REPLACING SUCH
<br />WORK UPON REQUIREMENTS. IN NO CASE SHALL THE CONTRACTOR(S) PROCEED WITH WORK THAT IS UNCLEAR OR
<br />IN CONTRADICTION WITHOUT FIRST RECEIVING INSTRUCTION FROM THE ARCHITECT, AT CONTRACTOR'S SOLE COSTS.
<br />MCUS MAJOR REMODEL
<br />322 S. CENTER ST., STOCKTON, CA 95243
<br />BUILDING INFORMATION
<br />ADDRESS:
<br />STREET ADDRESS 322 S. CENTER ST.
<br />CITY: STOCKTON
<br />STATE CA
<br />McDONALD'S REGION: PACIFIC SIERRA REGION
<br />STATE SITE CODE 004-3666
<br />COUNTY: TU ARE
<br />APN: 119-03-034 PARCEL 1
<br />STRUCTURE:
<br />EXISTING LIGHT GAUGE METAL STUD CONSTRUCTION w/
<br />WOOD TRUSSES. NEW CONSTRUCTION TO BE LIGHT
<br />GAUGE METAL FRAMING
<br />UTILITIES -
<br />GAS UTILITIES (EXISTING)
<br />ELECTRIC UTILITIES<E> TO REMAIN
<br />SPLIT UTILITIES <E> TO REMAIN
<br />BUILDING DATA:
<br />OCCUPANCY TYPE`
<br />ALLOWABLE AREA PER TABLE 503 BASIC ALLOWABLE
<br />FLOOR AREA PER 2016 CBC V -B = 6,000 S.F.
<br />CONSTRUCTION TYPE V -B
<br />NUMBER OF STORIES, 1
<br />BUILDING HEIGHT: <E> 19-6" T/PARAPET
<br />TOWER HEIGHTS, <E> 32'-0" TrrOWER
<br />PLAYPLACE HEIGHT N/A _
<br />CONDITIONED SPACE:
<br />COOLER/FREEZER:
<br />ADDITION:
<br />TOTAL:
<br />EXISTING PROPOSED
<br />6 063 .F.
<br />6 063 S.F.
<br />315 S.F.
<br />315 S.F.
<br />N/A
<br />369 S.F.
<br />6,378 S.F.
<br />6,747 S.F.
<br />OCCUPANT LOAD:
<br />DRAWING INDEX
<br />Cover & ADA
<br />DINING AREA PER TABLE (1004.1.1):
<br />42 SEATS
<br />PLAYPLACE
<br />/A
<br />EMPLOYEES:
<br />13
<br />CUSTOMER SERVICE:
<br />15
<br />CONVENIENCE STORE:
<br />33
<br />TOTAL OCCUPANT LOAD:
<br />103
<br />CONSULTANTS
<br />ARCHITECT )IGEN INCORPORATED
<br />L.S. ARCHITECT 516 W. Shaw Ave. Suite 101
<br />ELECTRICAL Fresno, CA 93704
<br />Tel: (55
<br />9) 268-2711
<br />CIVIL ENGINEER
<br />MQUA ENTERPRISE
<br />5699 N. 7th Street
<br />Fresno, CA 93710
<br />Tel: (559) 268-2711
<br />STRUCTURAL ENGINEER PLATINUM Engineering
<br />Solutions Inc.
<br />10648 N. HWY. 41
<br />Madera, CA 93638-9469
<br />Tel. (559) 439-0500
<br />Fax. (559) 433-6433
<br />MECHANICAL & LMR Engineering
<br />PLUMBING ENGINEER 1165 A Street
<br />Hayward, CA 94541
<br />Tel. (510) 733-2330
<br />Fax. (510) 733-0332
<br />BUILDING INFORMATION:
<br />BUILDING CODE:
<br />CALIFORNIA BUILDING CODE: 2016 CBC
<br />MECHANICAL CODE EDITION: 2016 CMC
<br />ELECTRICAL CODE EDITION: 2016 CEC
<br />PLUMBING CODE EDITION: 2016 CPC
<br />CALIFORNIA FIRE CODE 2016 CFC
<br />NEC: 2010
<br />CALIFORNIA ENERGY CODE: 2016 CEC
<br />CALIFORNIA CODE OF 2013 NFPA
<br />REGULATIONS/2010/TITLE 24
<br />DESIGN LOADS/ STANDARDS:
<br />ROOF LIVE LOAD: 20 PSF
<br />ROOF DEAD LOAD: 20 PSF
<br />WIND LOAD: 110 MPH
<br />EXPOSURE' C
<br />SOIL SITE CLASS D
<br />SOIL BEARING CAPACITIES: 1,500 PSF
<br />SPECIAL INSPECTIONS REQUIRED: 1,2.4,5 67
<br />SEISMIC CATEGORY: D
<br />SPECIAL INSPECTIONS (SEE ABOVE):
<br />1. PERIODIC INSPECTION FOR SEISMIC RESISTANCE IS
<br />REQUIRED FOR WOOD SHEAR WALLS, WOOD
<br />DIAPHRAGMS, DRAG STRUTS/COLLECTORS (CHORDS),
<br />SHEAR PANELS, SILL BOLTS, HOLD DOWN, ETC. WHERE
<br />NAILING IS 4" o.c. OR LESS (CBC 1707.3)
<br />2. RESPONSIBLE CONTRACTOR OF MAIN W1 ND- OR
<br />SEISMIC- FORCE RESISTING SYSTEMS (CBC 1709.1)
<br />3. SOILS COMPACTION & REPORTS
<br />4. CONCRETE CYLINDERS, 3 PER DAY w/ SLUMP TEST FOR
<br />CONCRETE SLABS & FOUNDATIONS. (3,000 psi)
<br />5. FIELD WELDING
<br />6. SUSPENDED METAL CEILING SYSTEMS.
<br />7. SEE GENERAL NOTES #32
<br />LIFE SAFETY SYSTEM:
<br />EMERGENCY LIGHTING: X YES _ NO
<br />EXIT SIGNS: X YES _ NO
<br />FIRE ALARM AND SMOKE
<br />DETECTION SYSTEMS: X YES _ NO
<br />PANIC HARDWARE: X YES _ NO
<br />FIRE SPRINKLERS: X YES _ NO
<br />LIFE SAFETY:
<br />A) THE TYPE I HOOD WILL BE EQUIPPED WITH AN
<br />APPROVED AUTOMATIC FIRE EXTINGUISHING
<br />SYSTEM.
<br />B) PLANS AND SPECIFICATIONS WILL BE SUBMITTED TO
<br />THE CITY OF STOCKTON , FIRE MARSHAL, FOR
<br />REVIEW, APPROVAL, AND PERMIT ISSUANCE PRIOR
<br />TO INSTALLATION OF ALL FIRE SUPPRESSION
<br />SYSTEMS.
<br />C) THE CONTRACTOR(S) SHALL NOT COMMENCE ANY
<br />O
<br />ADDITIONAL WORK, NOR INCUR ANY ADDITIONAL
<br />COSTS OR TIME(VIMOLE OR INPART) WHERE ANY
<br />SUCH COSTS AND OR TIME MAY OR DOES IMPACT
<br />THE OWNER, ARCHITECT, OR ENGINEER AND SUCH
<br />SHALL NOT BE INCURRED BY CONTRACTOR OR
<br />SUBCONTRACTOR WITHOUT PRIOR WRITTEN
<br />APPROVAL OF EACH AND EVERY AFFECTED PARTY
<br />(INCLUDING OWNER, ARCHITECT, AND ENGINEERS).
<br />NO CHANGES TO SPECIFICATIONS, PRODUCTS, OR
<br />CHANGE ORDERS WITHOUT ARCHITECT'S WRITTEN
<br />AUTHORIZATION. J
<br />HEALTH DEPARTMENT NOTES:
<br />PLANS SUBMITTED FOR RESTAURANTS SHALL BE APPROVED BY THE HEALTH DEPARTMENT PRIOR TO PLUMBING
<br />BACK CHECK PER 2016 CPC 101.3
<br />1. COMPLETED CONSTRUCTION MUST CONFORM TO ALL PROVISIONS OF THE CURRENT CALIFORNIA RETAIL
<br />FOOD CODE (CAL -CODE).
<br />2. THIS ESTABLISHMENT WILL REQUIRE A MINIMUM OF THREE INSPECTIONS PRIOR TO OPENING. IT IS THE
<br />RESPONSIBILITY OF THE OWNER AND/OR REPRESENTATIVE TO CONTACT THE GOVERNING HEALTH
<br />DEPARTMENT FOR THESE INSPECTIONS. THE CONTACT TIME FOR THESE INSPECTIONS SHOULD BE AS FOLLOWS:
<br />1ST INSPECTION: IMMEDIATELY AFTER INSTALLATION OF THE ROUGH PLUMBING BUT PRIOR TO CONCRETE POUR.
<br />2ND INSPECTION: AFTER SURFACES (WALLS, FLOORS CEILINGS, ETC) ARE COMPLETED BUT PRIOR TO EQUIPMENT
<br />INSTALLATION.
<br />3RD INSPECTION: UPON COMPLETION OF CONSTRUCTION, BUT PRIOR TO OPENING FOR BUSINESS.
<br />DEFERRED ITEMS:
<br />1, NOT USED
<br />2. ALL SIGNAGE (INCLUDING DRIVE-THRU MENU SIGNAGE) SHALL BE UNDER SEPARATE PERMIT AND WILL BE
<br />SUBMITTED TO THE PLANNING DIVISION AS A DEFERRED SUBMITTAL, ALL SIGNS SHALL COMPLY WITH PROVISIONS
<br />ESTABLISHED IN (MDP 2010.05).
<br />3. METAL CANOPIES & WALK IN COOLER TO BE PROVIDED BY OTHER AS A DEFERRED SUBMITTAL.
<br />4. NOT USED
<br />5. ALL ITEMS (ABOVE) REQUIRING DEFERRED SUBMITTAL SHALL BE BY SEPARATE PLAN CHECK SUBMITTAL & REVIEW BY
<br />THE LOCAL GOVERNING AGENCY & SHALL RECEIVE SEPARATE APPROVAL, PERMIT & FEES PAID PRIOR TO ISSUANCE OF
<br />PERMITS OF SUCH WORK.
<br />6, THE AVAILABLE FAULT CURRENT LETTER, PROVIDED BY THE UTILITY COMPANY (ON UTILITY COMPANY LETTERHEAD),
<br />SHALL BE PROVIDED TO THE CITY PRIOR TO THE FIRST FOUNDATION INSPECTION.
<br />REVISIONS
<br />DRAWING INDEX
<br />Cover & ADA
<br />n
<br />E D c B A
<br />K1 KITCHEN LAYOUT SHEET
<br />Z u
<br />AOb ADA Notes
<br />CV Cover Sheet
<br />K2.1 KITCHEN SCHEDULE & ELEVATIONSDUO
<br />AOd Finish Schedules & Details
<br />Al
<br />CVa Abbreviations Key & Symbols
<br />Floor Plan
<br />CG1 CAL Green
<br />v7
<br />0
<br />N
<br />V
<br />Z
<br />SITE & CIVIL
<br />_0
<br />Cl Grading Plan
<br />PLUMBING MBING PI ANS
<br />In
<br />AC1 Site Plan
<br />A1d Demolition Floor Plan
<br />P1 Water Piping Plan
<br />__
<br />LU
<br />ACta Site Notes & Details
<br />Y
<br />w p
<br />LU
<br />AC1b Typ, Site Details
<br />ECrt
<br />Ir
<br />o
<br />a d
<br />AC1c Trash Enclosure Details
<br />0 rn m
<br />P4 Water Piping Diagram
<br />AC1f Drive-Thru Details (FOR REF. ONLY)
<br />A3 Roof Plan
<br />0
<br />AO ADA Details
<br />n
<br />AOa ADA Notes
<br />K1 KITCHEN LAYOUT SHEET
<br />Z u
<br />AOb ADA Notes
<br />z � $
<br />z
<br />K2.1 KITCHEN SCHEDULE & ELEVATIONSDUO
<br />AOd Finish Schedules & Details
<br />Al
<br />LU - _ 24E '
<br />Floor Plan
<br />Ala Door/WindowSchedules/Details
<br />0
<br />N
<br />V
<br />Alb Toilet / Detail
<br />N N
<br />w
<br />A1c Exiting Plan
<br />PLUMBING MBING PI ANS
<br />>
<br />A1d Demolition Floor Plan
<br />P1 Water Piping Plan
<br />__
<br />Ale Front Counter Details
<br />P2 Waste and Vent Pian
<br />Y
<br />w p
<br />A2 Exterior Elevations
<br />ECrt
<br />A2a Exterior Elevations
<br />o
<br />a d
<br />0
<br />0 rn m
<br />P4 Water Piping Diagram
<br />�J
<br />0=
<br />A3 Roof Plan
<br />I
<br />W U o
<br />A4 Reflected Ceiling Plan
<br />H w
<br />Z
<br />A4a Ceiling Details
<br />m Z N
<br />0
<br />o t
<br />o
<br />ma W O
<br />A5 Seating Plan
<br />uE
<br />a o o
<br />3 U H 7
<br />A6 Wall Sections
<br />MECHANICAL
<br />a o U
<br />A8 Details
<br />_
<br />N mN O "
<br />A8a Details
<br />����
<br />" , N F_0
<br />F_ nC`7W OUo
<br />ASb Details
<br />(l ) i s
<br />N
<br />5
<br />cPFCIFIC TIONS w �\�c o /�dou
<br />SA1/SA3 Specifications r M a i
<br />4� N " i
<br />O U
<br />_ " w o
<br />';TRI Ir
<br />SOa Details
<br />SOb Details
<br />SOc Details
<br />S1 Foundation Plan
<br />S2 Roof Framing Plan
<br />S5 Foundation Details
<br />S6 Wall Sections & Details
<br />KITCHEN EQUIPMENT
<br />n
<br />K1 KITCHEN LAYOUT SHEET
<br />K2 KITCHEN EQUIPMENT PLAN
<br />K2.1 KITCHEN SCHEDULE & ELEVATIONSDUO
<br />Q
<br />V
<br />Y
<br />N
<br />PLUMBING MBING PI ANS
<br />P1 Water Piping Plan
<br />__
<br />3
<br />P2 Waste and Vent Pian
<br />0
<br />((�
<br />P3 Gas and Refrigerant Piping
<br />o
<br />a d
<br />0
<br />P4 Water Piping Diagram
<br />�J
<br />0=
<br />0
<br />N
<br />O v
<br />0
<br />o t
<br />o
<br />uE
<br />a o o
<br />MECHANICAL
<br />o
<br />a „�
<br />E o a
<br />o
<br />0
<br />MT1 Envelope Analysis
<br />����
<br />MT2 Envelope Analysis
<br />(l ) i s
<br />N
<br />M1 Ductwork Ian
<br />P
<br />v a
<br />E �
<br />z
<br />om
<br />rnv7
<br />0
<br />w
<br />a
<br />FLFrTRIQAL
<br />MCI
<br />EO.0 Electrical Site Plan
<br />a =
<br />N
<br />E1 Kitchen Electrical Rough -In Plan
<br />s -
<br />a a
<br />E1.3 Kiosk Plan & Elevation
<br />8 d
<br />ElA Menu Board Details
<br />Ff
<br />N
<br />E2.0 Lighting Plan
<br />o
<br />E3.0 Lighting Control
<br />E3.1 Pos Riser Diagram
<br />z
<br />EN1 Title 24 Compliance
<br />O
<br />EN2 Title 24 Compliance
<br />('
<br />EN3 Title 24 Compliance
<br />EN4 Title 24 Compliance
<br />SAN JOAQUIN COUNTY
<br />ENVIRONMENTAL HEALTH DEPARTMENT
<br />1868 E.HAZELTONAVE,
<br />z
<br />SMKTON,CA95205'
<br />o
<br />z
<br />(Pf)9) 4680
<br />Q
<br />zz
<br />S2
<br />O
<br />g
<br />W
<br />o
<br />p�p,
<br />proved[ witinchangp5 Sae RelnarlZ§
<br />>
<br />>
<br />a
<br />i7 Dlsepproyed: See R
<br />OW
<br />z
<br />w N
<br />II
<br />Remarks �Y iN� �� Y7 0 '1'I -1S
<br />a
<br />o
<br />U Y
<br />O O
<br />0
<br />o111
<br />C7
<br />60
<br />of
<br />z
<br />Y
<br />Z
<br />m
<br />o
<br />Date e7 BY
<br />0 Y
<br />¢
<br />Apprbvaf extends only to that which is shown'aA described
<br />" O
<br />m o
<br />o
<br />o
<br />hereon and does not authorize or approve any omission or
<br />w
<br />=
<br />"
<br />F S
<br />J
<br />deviation from requirements of stale laws or localordinances.
<br />THESE DRAWINGS, DESIGNS, SKETCHES, IDEAS,
<br />ARRANGEMENTS AS WELL AS ANY AND ALL
<br />ELECTRONIC FILES AND/OR DWGS ARE THE SOLE
<br />AND EXCLUSIVE PROPERTY OF VIGEN INC., AND
<br />MCDONALD'S CORP. , AND WERE CREATED AND
<br />DEVELOPED BY AND FOR THE ARCHITECTS
<br />WORK, NOTHING CONTAINED OR REPRESENTED
<br />ON THESE DOCUMENTS SHALL BE USED BY OR
<br />DISCLOSED TO ANY PERSON, FIRM OR
<br />CORPORATION FOR ANY PURPOSE WITHOUT
<br />THE EXPRESSED WRITTEN CONSEM OF VIGEN
<br />INC. THE WORK CONTAINED ON THESE DWGS
<br />AND DOCUMENTS IS CREATED ONLY FOR THIS
<br />PROJECT AT THIS TIME AND NO OTHER, AND
<br />NOT FOR OTHER RELATED, IMPLIED, OR FUTURE
<br />WORKIS! OR PROJECTISI.
<br />CV
<br />
|