|
i
<br />I- -
<br />A k-
<br />S
<br />TRAP AT RISER (TYP.)
<br />01
<br />L
<br />-C- - I - -C- L -c- -� _C_ -�
<br />II
<br />TRAP LEAVING REFRIGERATED ROOM
<br />EVAPORATION PIPING SYSTEM
<br />SCALE: N/A
<br />COOLER DIMENSION PLAN
<br />SCALE: 1/4"=1'-0"
<br />LEGEND
<br />---S--- SUCTION
<br />----L---- LIQUID
<br />- - - - C- - - - CONDENSATE DRAIN
<br />NOTE:
<br />ALL SUCTION LINES TO BE INSULATED
<br />CU -2
<br />L
<br />S -
<br />ROOF
<br />L
<br />S
<br />TRAP AT RISER (TYP.)
<br />L -c-�
<br />II
<br />TRAP LEAVING REFRIGERATED ROOM
<br />EVAPORATOR COILS
<br />0
<br />BOX LOAD
<br />REQUIREMENTS
<br />QTY.
<br />HEATCRAFT
<br />MODEL #
<br />FANS
<br />REFG.
<br />TMR E
<br />REFG.
<br />LBS.
<br />B.T.U.'S
<br />1 HR.
<br />EACH
<br />POWER
<br />SUPPLY
<br />BOX
<br />TEMP.
<br />F
<br />DEFROST
<br />HEATER
<br />FAN
<br />MOTOR
<br />AC
<br />EACH
<br />CFM
<br />MCA
<br />MCA
<br />CU -1
<br />COOLER
<br />40,034 BTU/H
<br />4
<br />LCA6110AB
<br />2
<br />1,300
<br />404A
<br />--
<br />9,400
<br />208/230/1/60
<br />+34
<br />7.8
<br />2.0
<br />MOH031 L63C
<br />LL 2
<br />REACH -IN FREEZER
<br />2,132 BTU/H
<br />1
<br />LCE694BB
<br />1
<br />335
<br />404A
<br />--
<br />2,800
<br />208/230/1/60
<br />-15
<br />5.7
<br />1.2
<br />BP REPM:
<br />CONDENSING UNITS
<br />0
<br />BOX LOAD
<br />REQUIREMENTS
<br />QTY-
<br />HEATCRAFT
<br />MODEL #
<br />SUCTION
<br />TEMP.
<br />REFG.
<br />TYPE
<br />R
<br />REFG.
<br />CHG.
<br />LBS,
<br />B T.U.'S
<br />HR
<br />EACH
<br />POWER
<br />SUPPLY
<br />DEFROST
<br />TIMER
<br />MIN
<br />CCT.
<br />AMP.
<br />MAX.
<br />FUSE
<br />SIZE
<br />COOLER
<br />40,034 BTU/H
<br />1
<br />MOH03OX63C
<br />+25'
<br />404A20.0
<br />®21000AM6
<br />208/230/3/60
<br />ELECTRIC
<br />38.0
<br />40
<br />DANIEL BRIAN
<br />CU 2
<br />FREEZERN
<br />2,132 BTU/H
<br />1
<br />MOH031 L63C
<br />-20'
<br />404A
<br />5.5
<br />3 281 0110' AMB.
<br />208/230/3/60
<br />ELECTRIC
<br />15.0
<br />25
<br />@ SCOTT CREEK DRIVE
<br />CODES AND STANDARDS
<br />NSF STANDARDS: COMPLY WITH APPLICABLE NATIONAL SANITATION
<br />FOUNDATION (NSF) STANDARDS AND RECOMMENDED CRITERIA. PROVIDE
<br />EACH PRINCIPAL ITEM OF FOOD SERVICE EQUIPMENT WITH A NSF
<br />SEAL OF APPROVAL"
<br />UL LABEL: WHERE AVAILABLE, PROVIDE UL LABELS ON PRIME
<br />ELECTRICAL COMPONENTS OF FOOD SERVICE EQUIPMENT. PROVIDE
<br />UL "RECOGNIZED MARKING" ON OTHER ITEMS WITH ELECTRICAL
<br />COMPONENTS SIGNIFYING LISTING BY UL, WHERE AVAILABLE.
<br />HEALTH CODE: INSTALL FOOD SERVICE EQUIPMENT IN ACCORDANCE
<br />WITH LOCAL HEALTH DEPARTMENT APPLICABLE REGULATIONS,
<br />1. SHOP DRAWINGS UPON APPROVAL OF BID, SUBMIT 3 SETS OF
<br />COMPLETE DETAILS, MECHANICAL AND ELECTRICAL REQUIREMENTS,
<br />AND INSTALLATION INSTRUCTIONS OF EACH ITEM. INCLUDE INFORMATION
<br />ON ROUGHING IN DIMENSIONS, SERVICE CONNECTION REQUIREMENTS,
<br />OPENINGS, DISPLAY AND LATCH DOOR MANUFACTURER'S INFORMATION,
<br />COMPLETE FLOOR PLANS AND EQUIPMENT SPECIFICATIONS.
<br />2. TAKE FIELD MEASUREMENTS TO ASSURE ACCURATE FIT OF FABRICATED
<br />EQUIPMENT.
<br />3. INCLUDE WARRANTY INFORMATION ON ALL EQUIPMENT.
<br />COOLER/FREEZER ALARMS
<br />COOLER/FREEZER ALARMS AS MANUFACTURED BY:
<br />NATIONAL CONTROLS CORPORATION
<br />1725 WESTERN DRIVE
<br />WEST CHICAGO, IL. 60185
<br />(800) 323-2593
<br />PROVIDE THE FOLLOWING:
<br />(1) DUAL KIT #TNC-TM100-KT2A
<br />KIT INCLUDES:
<br />• 2 THERMOMETER UNITS
<br />• 1 TEMPERATURE PROBES WITH 6'-0" WIRE
<br />• 1 TRANSFORMER
<br />• 1 STAINLESS STEEL TWIN ENCLOSURE
<br />ADDITIONAL PROBE WIRE #X02-22GNO-820
<br />INSTALLATION:
<br />*INSTALL THERMOMETER UNITS IN CASHIER AREA.
<br />*INSTALL TEMPERATURE PROBE IN EACH RESPECTIVE COOLER/FREEZER
<br />COMPARTMENT. SPLICE THE 6'-0" PROBE WIRE WITH ADDITIONAL
<br />PROBE WIRE AS REQUIRED TO RETURN TO CASHIER AREA.
<br />• COMPLETELY SEAL ANY AND ALL INTRUSIONS TO COOLER/FREEZER
<br />COMPARTMENTS.
<br />• LABEL ALL THERMOMETER UNITS PER RESPECTIVE COOLER/FREEZER
<br />COMPARTMENTS.
<br />• SET ALARM TEMPERATURE AS FOLLOWS:
<br />• WALK-IN COOLER: +35' F.
<br />• WALK-IN FREEZER: 0' F.
<br />• LOCATE TEMP. PROBES A MIN 2'-0" FROM WALL AND 5'-0" FROM DOOR.
<br />WALK-IN COOLER NOTES
<br />1.0 GENERAL NOTES -
<br />1.1 WALK-IN COOLER SHALL BE PREFABRICATED METAL CLAD PANELS
<br />BY CUSTOM COOLERS INC. OR EQUAL. DESIGNED IN MODULAR
<br />CONCEPT TO FACILITATE ACCURATE JOB SITE ASSEMBLY.
<br />2.0 PANEL CONSTRUCTION:
<br />2.1 ALL PANELS SHALL BE FOAMED -IN-PLACE CLASS 1, POLYURETHANE
<br />CONSTRUCTION WITH 3 1/2" COMPOSITE PANEL. THE "R" VALUE TO
<br />BE 30 WITH A DENSITY 6F 2.2 POUNDS PER CUBIC FOOT.
<br />2.2 THE PERIMETER OF ALL PANELS SHALL BE BUTT JOINT
<br />2.3 PANELS TO BE JOINED TOGETHER BY ENGAGING A CAM -ACTION
<br />LOCKING DEVICE. THE CAM ACTION DEVICE WILL DRAW THE SECTIONS
<br />TOGETHER TO FORM A TIGHT SEAL.
<br />2.4 STANDARD PANEL FINISH SHALL BE 26 GAUGE STUCCO EMBOSSED
<br />GALVANIZED STEEL SKIN EXTERIOR WITH WHITE INTERIOR.
<br />2.5 PROVIDE 7-1/2" DOOR SILL HEIGHTS FOR GLASS DISPLAY DOORS.
<br />2.6 INSULATION IS CLASS 1, POLYURETHANE FOAM WITH A FLAME SPREAD
<br />LESS THAN 25 AND A SMOKE DEVELOPMENT OF LESS THAN 450.
<br />2.7 CERTIFICATIONS: UL AND NSF APPROVED
<br />2.8 MEASUREMENTS AND CONFIGURATIONS REFER TO THIS SHEET.
<br />3.0 COOLER WALK-IN DOOR
<br />MANUFACTURED BY CUSTOM COOLERS, INC. OR EQUAL.
<br />3.1 36" x 82" CUSTOM *ANTHONY 103NT (HEAVY DUTY) ALL GLASS
<br />PASS-THRU DOOR, SLIMLINE BLACK HANDLE, PRO LEDs, NO
<br />THRESHOLD, CYLINDER DOOR LOCK, ALL BLACK FINISH DOOR & FRAME,
<br />STAINLESS STEEL INTERIOR/EXTERIOR 10" KICKPLATES.
<br />3.2 LOCATION AND SWING AS SHOWN ON THIS SHEET.
<br />3.3 FREEZER WALK-IN DOOR
<br />MANUFACTURED BY CUSTOM COOLERS, INC. OR EQUAL.
<br />3.4 DOOR SHALL BE NOMINAL 3 1/2" FOAMED -IN-PLACE CLASS 1,
<br />POLYURETHANE CONSTRUCTION.
<br />3.5 DOOR TO BE HINGED, IN -FIT, AND HAVE 36" HIGH DIAMOND PLATE
<br />KICK PLATES FOR INTERIOR AND EXTERIOR.
<br />3.6 HINGES SHALL BE CAM -RISE WITH BRIGHT SILVER ANODIZED FINISH
<br />ON FRAME AND DOOR TRIM, TWO HINGES PER DOOR.
<br />3.7 LATCH AND STRIKE TO HAVE A SATIN SURFACE CHROME FINISH WITH
<br />PROVISION FOR PADLOCK. LATCH TO HAVE INSIDE SAFETY RELEASE
<br />TO PREVENT ENTRAPMENT.
<br />3.8 DOOR TO HAVE REPLACEABLE GASKETS FOR A POSITIVE SEAL AND
<br />AN ADJUSTABLE VINYL WIPER GASKET FOR SEAL AT DOOR FRAME
<br />THRESHOLD.
<br />3.9 A FLUSH MOUNTED 2" DIAL THERMOMETER OF CORRECT TEMPERATURE
<br />RANGE SHALL BE PROVIDED AT THE DOOR. THE THERMOMETER SHALL
<br />BE EASILY CALIBRATED. THE THERMOMETER SENSING BULB ON THE
<br />INTERIOR OF THE DOOR SECTION TO HAVE PROTECTIVE COVER.
<br />3.10 LIGHTING SHALL CONSIST OF THREE VAPOR -PROOF LIGHT FIXTURES
<br />TO BE FURNISHED LOSE, AND A LIGHT SWITCH WITH PILOT LIGHT
<br />FLUSH MOUNTED ON EXTERIOR. THE WIRING SYSTEM SHALL BE
<br />APPROVED BY UNDERWRITERS LABORATORY.
<br />3.11 PROVIDE LOCKS ON DOORS AS INDICATED ON COOLER PLAN.
<br />3.12 PROVIDE WALL BUMPER GUARD
<br />4.0 GLASS DISPLAY DOORS:
<br />MANUFACTURED BY ANTHONY OR EQUAL
<br />4.1 30" X 75" H. DISPLAY DOORS (SILL AT 7-1/2" A.F.F.)
<br />4.2 ENERGY SAVER CONTROLS
<br />4.3 FINISH TO BE SMOOTH BLACK.
<br />4.4 COOLER DISPLAY DOORS SHALL HAVE 2 -PANE GAS FILLED NON -HEATED,
<br />INSULATED SAFETY GLASS
<br />4.5 LED LIGHTING
<br />4.6 36" DEEP SHELVES, (7) PER DOOR
<br />4.7 KEY CYLINDER LOCK AT EACH DOOR.
<br />4.8 COOLER DISPLAY DOORS SHALL HAVE 3 -PANE HEATED SAFETY GLASS
<br />5.0 REFRIGERATION•
<br />5.1 ALL EQUIPMENT MUST CONFORM TO CONDENSING UNITS AND UNIT
<br />COOLERS SCHEDULE AS OUTLINED ON THIS SHEET. EQUIPMENT MUST
<br />HAVE UL LISTING FOR THE APPLICATION AS SPECIFIED.
<br />5.2 CONDENSING UNIT AS SPECIFIED SHALL HAVE THE FOLLOWING:
<br />1. HIGH EFFICIENCY ALUMINUM FIN. COPPER TUBE CONDENSER.
<br />2. COMPRESSOR CONTRACTOR.
<br />3. HIGH AND LOW PRESSURE CONTROLS
<br />4. WEATHER RESISTANT HOUSING WITH WEATHER-PROOF ELECTRICAL
<br />CONTROL BOX.
<br />5. ACCESS GUARD.
<br />6. LOW AMBIENT CONTROL VALVE (CVP II) FPR FLOATING HEAD.
<br />7. CRANKCASE HEATER.
<br />8. LIQUID LINE FILTER DRIER, SIGHT GLASS AND SERVICE VALVE.
<br />9. ELECTRIC DEFROST TIMER.
<br />10. EXPANSION VALVES.
<br />11. THERMOSTAT AND SOLENOID.
<br />5.3 EVAPORATOR COILS SPECIFIED IN EVAPORATOR COIL SCHEDULE.
<br />5.4 EXPANSION VALVE SHALL BE SIZED BY UNIT COOLER MANUFACTURER
<br />FOR PROPER REFRIGERATION. AS HEAD PRESSURE IS ALLOWED TO
<br />DROP DURING LOW AMBIENT CONDITIONS, EXPANSION VALVE NEEDS
<br />TO BE OVERSIZED TO ALLOW FLOW AT LOWER PRESSURE DIFFERENTIAL
<br />RATIO.
<br />5.5 THERMOSTATS SHALL BE FURNISHED LOOSE FOR EACH SYSTEM AND
<br />SHALL BE WHITE RODGERS MODEL #1609-101 OR EQUAL, TAMPER -PROOF
<br />WITH PROPER TEMPERATURE RANGE, AS REQUIRED ON THIS DRAWING.
<br />OPTIONAL MANUFACTURERS: JOHNSON OR RANCO OR EQUAL.
<br />5.6 SOLENOIDS SHALL BE FURNISHED LOOSE FOR EACH SYSTEM AS
<br />RECOMMENDED BY CONDENSING UNIT MANUFACTURER.
<br />5.7 CONDENSATE PIPING SHALL BE COPPER OR PVC AND TRAPPED AFTER
<br />WALL PENETRATION. HEAT TAPE AND INSULATE WHERE REQUIRED
<br />TO PREVENT FREEZE UP.
<br />5.8 REFRIGERATION WARRANTY SHALL BE A MINIMUM OF ONE (1) YEAR PARTS
<br />FOUR (4) YEAR COMPRESSOR WARRANTY AND NINETY (90) DAYS SERVICE.
<br />5.9 HEAT SENSOR TO BE LOCATED 1'-2" ABOVE DOOR FRAME TO
<br />ALLOW FOR GRAPHICS INSTALLATION.
<br />6.0 REFRIGERATION INSTALLATION
<br />6.1 EVAPORATOR COILS SHALL BE MOUNTED FROM CEILING WITH 5/16"
<br />MINIMUM FASTENERS.
<br />6.2 CONDENSING UNITS ARE MOUNTED ON THE ROOF AND MUST BE LEVEL
<br />WITH IT'S BASE ANCHORED TO PREVENT MOVEMENT. ALLOW PROPER
<br />CLEARANCE FOR AIR SUPPLY TO AND FROM UNIT AND FOR PROPER
<br />MAINTENANCE ACCESS.
<br />6.3 SUCTION LINES AT TOP OF RISER ON ROOF SHALL BE SLOPED 1" PER
<br />TEN (10) FEET TO COMPRESSOR. ALL SUCTION LINES SHALL BE SIZED
<br />AND TRAPPED. INSULATE TO PREVENT SWEATING.
<br />6.4 LIQUID LINES AND SOLENOID VALVE SHOULD BE INSTALLED IN THE
<br />LIQUID LINE JUST AHEAD OF EXPANSION VALVE IN COOLER.
<br />6.5 BRAZING SHALL BE SILVER BEARING SOLDER HIGH TEMPERATURE OR
<br />EQUIVALENT ALLOY SUITABLE FOR THIS APPLICATION. NO "SOFT
<br />SOLDERS" PERMISSIBLE. NITROGEN IS TO BE PURGED THROUGH THE
<br />SYSTEM DURING BRAZING.
<br />6.6 LEAK TEST THE ENTIRE SYSTEM AFTER ALL REFRIGERATION
<br />CONNECTIONS HAVE BEEN COMPLETED. LEAK TESTING SHALL BE
<br />PERFORMED WITH AN ELECTRONIC LEAK DETECTOR,
<br />6.7 THE SYSTEM MUST BE EVACUATED WITH A VACUUM PUMP, HAVING
<br />THE CAPABILITY OF PULLING A VACUUM OF 50 MICRONS OR LESS.
<br />THE PUMP SHOULD BE CONNECTED TO BOTH THE HIGH AND LOW
<br />SIDES OF THE SYSTEM.
<br />6.8 DURING CHARGING AND START-UP MAKE SURE SHIPPING RESTRAINTS
<br />ARE REMOVED AND ALL ELECTRICAL AND MECHANICAL CONNECTIONS
<br />ARE TIGHT. SET HIGH LOW PRESSURE SWITCH AS REQUIRED.
<br />6.9 INSTALLATION AND SERVICE OF THIS EQUIPMENT SHOULD BE
<br />PERFORMED BY QUALIFIED AND EXPERIENCED REFRIGERATION
<br />MECHANICS. INSTALL ALL EQUIPMENT, PIPING IN ACCORDANCE WITH
<br />LOCAL AND NATIONAL CODES AND IN CONFORMANCE WITH GOOD
<br />PRACTICE REQUIRED FOR PROPER OPERATION.
<br />CLIENT:
<br />ARCO
<br />BP WEST COAST PRODUCTS, LLC
<br />18215 72ND AVENUE SOUTH
<br />KENT, WA 98032
<br />(425)251-6222
<br />(425)251-8782 FAX
<br />CML ENGINEERING, LAND PLANNING,
<br />SURVEYING, ENVIRONMENTAL SERVICES
<br />NO. I DATE I REVISION DESCRIPTION
<br />D5/16/16 BP APPROVED EQUIPMENT PLAN
<br />07/13/18 PERMIT SUBMITTAL
<br />0
<br />in
<br />n
<br />a
<br />ro
<br />N
<br />0
<br />E
<br />i=
<br />0
<br />3
<br />N
<br />d
<br />0
<br />0
<br />0
<br />U
<br />U
<br />/
<br />0
<br />O
<br />n
<br />O
<br />N
<br />O
<br />0
<br />0
<br />L�
<br />0
<br />0
<br />zL
<br />0
<br />SEAL•
<br />OF CAL /FO
<br />�2
<br />DANIEL BRIAN
<br />09 GOALWIN 7
<br />� o-leass
<br />r
<br />n REN. 8/31/17 �G
<br />F ySep ARC�\C
<br />DEVELOPMENT INFORMATION:
<br />ARCO NTI
<br />MODIFIED
<br />3000 am/pm
<br />w/ 26'x65' CAR WASH
<br />FUEL CANOPY w/ 8 MPD's
<br />SITE ADDRESS:
<br />TRINITY PARKWAY
<br />@ SCOTT CREEK DRIVE
<br />STOCKTON,CA
<br />FACILITY # TBD
<br />DFSGNED BY:
<br />MCE ZWIU-
<br />CHECKED BY:
<br />BP REPM:
<br />DRANK BY:
<br />ALLIANCE PM:
<br />VERSION:
<br />PREECT NO:
<br />16700
<br />DRAWING TITLE:
<br />COOLER
<br />PACKAGE
<br />SHEET NO:
<br />01.2
<br />0
<br />in
<br />n
<br />a
<br />ro
<br />N
<br />0
<br />E
<br />i=
<br />0
<br />3
<br />N
<br />d
<br />0
<br />0
<br />0
<br />U
<br />U
<br />/
<br />0
<br />O
<br />n
<br />O
<br />N
<br />O
<br />0
<br />0
<br />L�
<br />
|