|
ALL CONNECTIONS FROM CAPTIVE-AIRE DUCT PERMECHANICAL CONTRACTORS'S PLANS.EXHAUST FANS TO TURN ON IN EVENT OF FIRE.ALL PLUMBING "FIELD" CONNECTIONS AND RELATEDINTERCONNECTIONS BY PLUMBING CONTRACTORS.INSTALLING CONTRACTORS.ALL ELECTRICAL "FIELD" CONNECTIONS AND RELATEDINTERCONNECTIONS BY ELECTRICAL CONTRACTORS.HANGING BRACKETS LOCATED AND WELDED AS SHOWN ONCOOKING EQUIPMENT TO SHUTOFF IN EVENT OF FIRE.PLANS. ALL OTHER HANGER MATERIALS PROVIDED BYALL LIGHTS FIXTURE SHOWN INSTALLED BY CAPTIVE-AIREARE FACTORY PREWIRED. INTERCONNECTIONS BETWEENHOODS AND TO SWITCHES BY ELECTRICAL CONTRACTORS.SEISMIC RESTAINTS ARE RESPONSIBILITY OFINSTALLING CONTRACTORS ASSUME ALL RELATEDKITCHEN HOODS MUST BE BALANCED WITH KITCHEN.KITCHEN SHALL BE NEGATIVE WITH RESPECT CODE REQUIREMENTS IN EFFECT PRIOR TO ANYACCURACY, INTEGRATION, AND ADMINISTRATION OFDATA CONTAINED ON THESE DOCUMENTS FORRELEASE FOR PRODUCTION OF EQUIPMENT SHOWN.REPONSIBILITY FOR VERIFICATION OF DIMENSIONALINSTALLING CONTRACTOR.COMMENCEMENT OF FABRICATION.MUST BE RECEIVED BY THE FACTORY PRIOR TORESTAURANT SHALL BE POSITIVE WITH RESPECTLAMPS FOR LIGHT FIXTURES BY INSTALLING CONTRACTORS.WRITTEN HOOD DIMENSIONS HAVE PRECEDENCE OVER SCALE.SIGNED AND "APPROVED" COPIES OF THIS DOCUMENTMade From 430 Stainless SteelETL Listed Grease Extracting FiltersCaptiveAire Captrate Solo FilterTO DINING AREA.TO AMBIENT PRESSURE.12.14.13.15.ADDITIONALINSTALLATION7.10.11.9.8.BALANCE1.6.2.4.5.3.DIM FROMHANGING ANGLE IS PRE-PUNCHED AT FACTORY36"X36"2.00"4.166"4.166"2.246"TOTAL DUCT AREA=144 XROD AND NUTS TO BE SUPPLIED BY INSTALLING CONTRACTOREXHAUST CFM=LENGTH OF HOOD X CFM/LIN.FT. (LOAD)SUPPLY CFM=EXHAUST CFM X PERCENTAGE REQUIREDCAPTIVE-AIRE HOODS HAVE OPTIONAL CLEARANCEREDUCTION SYSTEMS AVAILABLE AS FOLLOWS:#3054804-001#3054804-002NON-COMBUSTIBLECOMBUSTIBLELIMITED-COMBUSTIBLEMATERIAL&2847BDBACKSHELFVHB/VHB-GDIMS BY SIZEFRONT/BACKDUCT LENGTH=HOOD STYLEND2-PSP-FND2CANOPY*REAR1/2" DIA. ALL THREAD RODCONNECTED TO ROOF JOISTTHROUGH ANOTHER HANGINGANGLECLEARANCE REDUCTION SYSTEM48"X48"-2.246"NONE REQUIRED3" UNINSULATED STANDOFF1" INSULATED STANDOFF14.25"42"X42"2.246"DUCT DEPTHTOTAL DUCT AREAFPM(*)CFM1/2" DIA. HEAVY DUTY NUTONE ABOVE AND ONE BELOWDIM FROMFRONT2.246"2.246"(30"H)FRONTDIM FROM2.246"2.246"(24"H)HANGING ANGLEE.T.L. LISTING = 3054804-001 WITHOUT EXHAUST DAMPER 3054804-002 WITH EXHAUST DAMPERHOOD CALCULATIONS FOR HOOD #1FREE AREA OF FILTER(S):11' 0" OF HOOD X 200 CFM / LIN. FT. OF HOOD MIN. = 2200 CFM EXHAUST MIN.&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,11483 CFM EXHAUST / 1.4 SQ. FT. = 2160 FPMFOR CANOPY STYLE, SINGLE, REAR-BANK FILTER HOODSACTUAL EXHAUST CFM = 3025 CFM16" dia. EXHAUST RISER = 201.06 SQ. IN. / 144 = 1.4 SQ. FT.16" X 16" = 1.35, 16" X 20" = 1.73, 20" X 20" = 2.238 X 1.73 = 13.843025 CFM EXHAUST / 13.84 SQ. FT. (FILTER AREA) = 218 FPME.T.L. LISTING = 3054804-001 WITHOUT EXHAUST DAMPER 3054804-002 WITH EXHAUST DAMPERHOOD CALCULATIONS FOR HOOD #2FREE AREA OF FILTER(S):7' 2" OF HOOD X 150 CFM / LIN. FT. OF HOOD MIN. = 1075 CFM EXHAUST MIN.&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,11483 CFM EXHAUST / .785 SQ. FT. = 1889 FPMFOR CANOPY STYLE, SINGLE, REAR-BANK FILTER HOODSACTUAL EXHAUST CFM = 1483 CFM12" dia. EXHAUST RISER = 113.1 SQ. IN. / 144 = .785SQ. FT.16" X 16" = 1.35, 16" X 20" = 1.73, 20" X 20" = 2.235 X 1.73 = 8.651483 CFM EXHAUST / 8.65 SQ. FT. (FILTER AREA) = 171 FPME.T.L. LISTING = 3054804-001 WITHOUT EXHAUST DAMPER 3054804-002 WITH EXHAUST DAMPERHOOD CALCULATIONS FOR HOOD #3FREE AREA OF FILTER(S):14' 6" OF HOOD X 150 CFM / LIN. FT. OF HOOD MIN. = 2175 CFM EXHAUST MIN.&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,12900 CFM EXHAUST / 1.57 SQ. FT. = 1847 FPMFOR CANOPY STYLE, SINGLE, REAR-BANK FILTER HOODSACTUAL EXHAUST CFM = 2900 CFM(2) 12" dia. EXHAUST RISER = 226.2 SQ. IN. / 144 = 1.57 SQ. FT.16" X 16" = 1.35, 16" X 20" = 1.73, 20" X 20" = 2.2311 X 1.73 = 19.032900 CFM EXHAUST / 19.03 SQ. FT. (FILTER AREA) = 152 FPME.T.L. LISTING = 3054804-001 WITHOUT EXHAUST DAMPER 3054804-002 WITH EXHAUST DAMPERHOOD CALCULATIONS FOR HOOD #44' OF HOOD X 100 CFM / LIN. FT. OF HOOD MIN. = 400 CFM EXHAUST MIN.&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,1&22.,1*(48,30(17 &)0/,1)72)+22'0,1600 CFM EXHAUST / .545 SQ. FT. = 1100 FPMFOR CANOPY STYLE, SINGLE, REAR-BANK FILTER HOODSACTUAL EXHAUST CFM = 600 CFM10" dia. EXHAUST RISER = 78.54 SQ. IN. / 144 = .545 SQ. FT.K-5.1KITCHEN EXHAUST HOOD DWGSJOB NO.:SHEET:DATE:REVISIONS:The Wolff CompanyÄ&GEGODGTReynolds Ranch Senior LivingLodi, California'%JCODGTU5VTGGV2JQGPKZ#<X<br /> ÄHZ<br /> Ä%114&+0#6+10%+6;%1//'0654'8+5+10
|