|
REVISIONS
<br /> CALIFORNIA RETAIL FOOD CODE GENERAL NOTES LUMINAIRE SCHEDULE ELECTRICAL POWER SYMBOLS IFP 04.05.2022
<br /> ARTICLE 2. LIGHTING 1. THESE DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION ID MANUFACTURER OUTPUT VOLTAGE INPUT V.A DRIVERS HOUSING MOUNTING REMARKS I-Q DUPLEX RECEPTACLE, NEMA 5-15R, +18" UON
<br /> 114252. UNLESS APPROVED BY THE BUILDING DEPARTMENT. TO BE SELECTED BY LED PENDANT@ I-@ DOUBLE DUPLEX RECEPTACLE, NEMA 5-15R, +18" UON
<br /> A OWNER 2800 Lumens 120-277 28 0-10V STEEL 9'AFF LED PENDANT LIGHTS
<br /> IN EVERY ROOM AND AREA IN WHICH ANY FOOD IS PREPARED
<br /> 2. THE ELECTRICAL DRAWINGS ARE DIAGRAMMATIC ONLY, AND NOT HALO 80CRI, 3500°K k� SWITCHED DUPLEX RECEPTACLE, OCCUPANCY SENSOR MANUFACTURED, PROCESSED, OR PREPACKAGED, OR IN WHICH TRACK CONTROLLED, NEMA 5-15R, +18 INTENDED TO SHOW ROUTING OF CABLES AND CONDUITS WHICH "
<br /> UON
<br /> DEVICES ARE NOTN
<br /> O
<br /> U. . .
<br /> EQUIPMENT OR UTENSILS ARE CLEANED, SUFFICIENT NATURAL OR SHALL BE DETERMINED IN THE FIELD, LZRC200.5 B1200MB- LED 8' LINE VOLTAGE TRACK WITH k� DOUBLE DUPLEX WITH 1 SWITCHED DUPLEX OCCUPANCY
<br /> ARTIFICIAL LIGHTING SHALL BE PROVIDED TO PRODUCE THE SHOWN TO SCALE, AND THEREFORE CANNOT ALWAYS BE SHOWN IN LZRC200.5CB120 ( )
<br /> THEIR EXACT LOCATION. B 850 Lumens 120 12 ELV ALUMINUM SURFACE LED HEADS, 0.5A END FEED SENSOR CONTROLLED AND (1 ) DUPLEX (NORMAL POWER)
<br /> FOLLOWING LIGHT INTENSITY, WHILE THE AREA IS IN USE: FIXTURES SOCRI, 3500°K CURRENT LIMITERS. WITH COMMON FINISH COVER PLATE, NEMA 5-15R, +18 UON E
<br /> L80808FL9035M B-FRE F-
<br /> (A) AT LEAST 10-FOOT CANDLES AT A DISTANCE OF 30 z
<br /> INCHES ABOVE THE FLOOR, IN WALK-IN REFRIGERATION 3. EXISTING DEVICES SHOWN WERE TAKEN FROM EXISTING DRAWINGS, 808302-PK-DIF-20 k@ DUPLEX RECEPTACLE WITH GROUND FAULT CIRCUIT INTERRUPTER Q 0 LO
<br /> UNIT, DRY FOOD STORAGE AREAS.INSIDE EQUIPMENT SUCH NOT "AS BUILT" DRAWINGS AND LIMITED SITE SURVEYS, AND MAY OR EQUIVALENT NEMA 5-15R, +18" UON J U 0
<br /> AS REACH-IN AND UNDER-COUNTER REFRIGERATORS. NOT BE COMPLETELY ACCURATE. THE ELECTRICAL TRADE SHALL GOTHAM LED � O
<br /> VISIT JOB SITE AND VERIFY CONDITIONS PRIOR TO BIDDING. NOTIFY C EVO 35/156AR MD LSS 1572 Lumens 120-277 18.5 0-10V STEEL RECESSED 6" LED DOWNLIGHT S= SHOW WINDOW RECEPTACLES z
<br /> (B) AT LEAST 20-FOOT CANDLES FOR THE FOLLOWING: THE ARCHITECT/OWNER OF ANY DISCREPANCIES. MVOLT EZ10 NPS80EZ 80CRI, 3500°K o O
<br /> (1) AT A SURFACE WHERE FOOD IS PROVIDED FOR LITHONIA LED C}' NON-FUSED DISCONNECT SWITCH, SIZE AS REQUIRED � �
<br /> CONSUMER SELF-SERVICE OR WHERE FRESH PRODUCE 2TL240L-FW-Al2-MVOLT- 2X2 LED TROFFER WITH HEIGHT z N
<br /> OR PREPACKAGED FOODS ARE SOLD OR OFFERED 4. BRANCH CIRCUITRY MAY NOT BE SHOWN FOR EXISTING DEVICES. D 2TL2-4 L-FW-0 4000 Lumens 120-277 35 0-1ov STEEL RECESSED CONTROL �' FUSED DISCONNECT SWITCH WITH TIME DELAY FUSES SIZED PER UNIT cn NO
<br /> THE ELECTRICAL TRADE SHALL RELOCATE EXISTING BRANCH 80CRI, 4000°K u, �C
<br /> FOR CONSUMPTION. OR EQUIVALENT NAMEPLATE OR AS NOTED. DISCONNECT SHALL ACCEPT MAXIMUM
<br /> CIRCUITRY AND MAKE ALL NECESSARY RECONNECTIONS AS -
<br /> (2) AT A DISTANCE OF 30 INCHES ABOVE THE FLOOR IN z
<br /> LED RECOMMENDED FUSE SIZE.
<br /> REQUIRED TO FACILITATE REMODEL. VERIFY ALL WORK REQUIRED ON TO BE SELECTED BY WALL @ LED GOOSE NECK DECORATIVE 0111AREAS USED FOR HAND WASHING WARE WASHING, AND THE JOB AND RECORD ON RECORD DRAWINGS. E OWNER 1500 Lumens 120-277 15 0-1ov STEEL 9 AFF FIXTURES cD Ln
<br /> EQUIPMENT AND UTENSIL STORAGE, AND IN TOILET 80CRI, 3500°K OJ Q JUNCTION BOX, SIZE AND TYPE AS REQUIRED z E
<br /> 3
<br /> ROOMS. 5. ALL ELECTRICAL WORK SHALL CONFORM WITH THE 2019 EDITION OF LITHONIA EXIT/EMERGENCY COMBO WITH
<br /> LHQM LED R HO REMOTE LED HEAD. PROVIDE ® RELAY PACK FOR CONTROLLED RECEPACLES E SS/0
<br /> ROOMS DURING PERIODS OF CLEANING.
<br /> ( ) AT SURFACE IN ALL FOOD PREPARATION AREAS AND THE CALIFORNIA ELECTRICAL CODE AS WELL AS ALL LOCAL CODES X LED 120-277 43 -OR EQUIVALENT . - MIN OF 90 MINS BACKUP RAF Q N
<br /> (C) AT LEAST 5 IS WORKING WITH FOOD OR WORKING WITH DURATION.
<br /> EMPLOYEE IS .FOOT CANDLES AT A SURFACE WHERE A FOOD & REQUIREMENTS. LITHONIA EMERGENCY FIXTUREPROVIDE COMBINATION TELE/DATA OUTLET, +18" UON. RING AND STRING. AD q� F
<br /> �
<br /> UTENSILS 6. ALL EQUIPMENT INSTALLED OR CONNECTED BY ELECTRICAL TRADE Y ELM2 LEDSD LED 120-277 6 - - - MIN OF 90 MINS BACKUP
<br /> OR EQUIPMENT SUCH AS KNIVES, SLICERS, GRINDERS, OR SHALL BE LABELED OR CERTIFIED FOR ITS USE BY A NATIONALLY DURATION. ® EXHAUST FAN, N.I.E.S., CONNECT AS REQUIRED L
<br /> SAWS
<br /> RECOGNIZED TESTING LABORATORY.
<br /> WHERE EMPLOYEE SAFETY IS A FACTOR. AND IN OTHER 7. REFER TO MECHANICAL AND PLUMBING DRAWINGS FOR EXACT BRANCH CIRCUIT PANEL, SEE PANEL SCHEDULES * No. 67047
<br /> AREAS LOCATIONS OF EQUIPMENTREFER TO MECHANICAL PLUMBING AND PANEL SCHEDULE "E" Exp. 09-30-2022
<br /> .
<br /> AND ROOMS DURING PERIODS OF CLEANING. co 7 o SIGNAL OR CONTROL PANEL, TYPE AS INDICATED s� �I VI\-
<br /> ELECTRICAL DRAWINGS AND SPECIFICATIONS FOR POWER AND Z RECESSED MOUNTED 120/208V. 3 Ph. 4W. 200 AMP BUS Z qlF OF CAO��
<br /> 114252.1. CONTROL REQUIREMENTS AND WIRING DIAGRAMS.. NEMA 1 200 AMP MLO 2 IDENTIFICATION TAG FOR EQUIPMENT PROVIDED BY M.C.
<br /> o FED FROM 200A REMOTE CIRCUIT BREAKER VERIFY kAIC o CONNECT EQUIPMENT AS INDICATED OR AS REQUIRED.
<br /> (A) EXCEPT AS SPECIFIED IN SUBVERSION (b), LIGHT BULBS 8. WHERE ELECTRICAL CONDUIT ENTERS A WALL, CEILING OR FLOOR, 0 DESCRIPTION KVA BKR CKT Ph. A Ph. B Ph. C CKT BKR KVA DESCRIPTION
<br /> SHALL THE OPENING AROUND THE CONDUIT SHALL BE TIGHTLY SEALED. POS #11 0.36 20-1 1 1.6 2 20-1 1.24 ICE MAKER #31.1
<br /> BE SHIELDED, COATED, OR OTHERWISE SHATTER-RESISTANT 9. CONDUIT INSIDE BUILDING SHALL BE EMT OR RSC. FLEXIBLE STEEL REF PREP TABLE #2 0.67 20-1 3 0.9 4 20-1 0.24 SODA MACHINE #31 ELECTRICAL SYMBOLS
<br /> IN OVEN #7 1.68 20-1 5 2.0 6 20-1 0.36 SODA COUNTER RECEPTS
<br /> AREAS WHERE THERE IS NON-PREPACKAGED CONDUIT MAY BE USED IN SHORT LENGTHS WHERE FLEXIBILITY IS REF PREP TABLE #2 0.67 20-1 7 1.6 8 20-1 0.90 DINING RECEPTS RECESSED LIGHT FIXTURE - MOUNTED IN T-BAR
<br /> READY-TO-EAT REQUIRED FOR MOVEMENT OR VIBRATION. COOK AREA RECEIPT 0.18 20-1 9 0.7 10 20-1 0.50 SHOW WINDOW RECEPTS
<br /> FOOD, CLEAN EQUIPMENT, UTENSILS, AND LINENS, OR DESK RECEPTS 0.36 20-1 11 1.0 12 20-1 0.60 COUNTER TOP REF MERCH #12 ® RECESSED DOWNLIGHT
<br /> UNWRAPPED SINGLE-USE ARTICLES. 10. FLEXIBLE METALLIC CONDUIT MAY BE USED FOR BRANCH CIRCUITS PREP AREA RECEPTS 0.36 20-1 13 0.5 14 20-1 0.18 ROOF RECEPTS LED PENDANT LIGHT
<br /> (B) SHIELDED, COATED, OR OTHERWISE SHATTER-RESISTANT WHERE METALLIC CONDUIT IS SHOWN. METAL CLAD CABLE MAY BE MEAT #21 0.67 20-1 15 1.9 16 20-1 1.20 OVEN #5
<br /> USED FOR BRANCH CIRCUITS WHERE CONCEALED WITHIN WALLS. EXIT SIGN WITH EMERGENCY LIGHT
<br /> BULBS NEED NOT BE USED IN AREAS USED ONLY FOR
<br /> OFFICE RECEPTS 0.36 20-1 17 1.0 18 20-1 0.67 REF PREP TABLE #2
<br /> STORING PREPACKAGED FOOD IN UNOPENED PACKAGES, IF 11. PROVIDE A GROUNDING CONDUCTOR IN ALL FLEXIBLE CONDUITS. PREP AREA RECEPTS 0.36 20-1 19 1.0 20 20-1 0.67 REF PREP TABLE #2 NOTE: UPPER CASE LETTER INDICATES FIXTURE TYPE - SEE
<br /> THE INTEGRITY OF THE PACKAGES CANNOT BE AFFECTED LIGHTING 0.80 20-1 21 2.2 22 20-1 1.44 TABLE HOT FOOD WELL #8 FIXTURE SCHEDULE. LOWER CASE LETTER INDICATES
<br /> BY
<br /> BROKEN GLASS FALLING ONTO THEM AND THE PACKAGES 12. THE COMPLETE SYSTEM SHALL BE GROUNDED PER CEC ART. 250. EMERGENCY LTG 0.10 20-1 23 1 0.3 24 20-1 0.20 HOOD #15 CONTROL LEG.
<br /> 08 HEF-1 6 26 20-1 1
<br /> 50 20-1 25 1. .
<br /> ARE CAPABLE OF BEING CLEANED OF DEBRIS FROM SIGN 0. LOW VOLTAGE DIMMER LIGHT SWITCH, +44„ UON
<br /> BROKEN 13. GENERAL PURPOSE 120V LIGHTING AND RECEPTACLE CIRCUITS SPARE 20-1 27 1.1 28 20-1 1.08 OVEN #14 4
<br /> OVER 100' LONG SHALL BE 10 CU, U.O.N. GENERAL PURPOSE SPARE 20-1 29 1.1 30 20-1 1.08 OVEN #14
<br /> BULBS BEFORE THE PACKAGES ARE OPENED. 277V LIGHTING CIRCUITS OVER 300' LONG SHALL BE #10 CU, SPARE 20-1 31 32 20-1 SPARE SINGLE POLE LIGHT SWITCH, +44" UON
<br /> (C) INFRARED AND OTHER HEAT LAMPS SHALL BE PROTECTED U.O.N. SPARE 20-1 33 0.5 34 20-1 0.50 1 DOOR REF #18 os
<br /> AGAINST BREAKAGE BY A SHIELD SURROUNDING AND OCCUPANCY SENSOR, CEILING MOUNTED
<br /> EXTENDING BEYOND THE BULB SO THAT ONLY THE FACE SPARE 20-1 35 0.5 36 20-1 0.50 1 DOOR REF #17
<br /> OF 14. PROVIDE TYPEWRITTEN SCHEDULES INDICATING LOAD DESCRIPTION 3.84 37 4.3 38 20-1 0.50 1 DOOR REF #17 �L DAYLIGHT CONTROLS, CEILING MOUNTED
<br /> THE BULB IS EXPOSED, OR BY USING APPROVED COATED FOR ALL CIRCUITS IN PANELBOARDS. AC-1 3.84 50-3 39 4.5 40 20-1 0.70 2 DOOR REF #19 SWITCH SUBCRIPTS: a, b, c, etc. = DEVICE CONTROLLED.
<br /> SHATTER RESISTANT BULBS. 15. CONTRACTOR TO PERFORM TESTING, ADJUSTMENT AND REPORTING 3.84 41 3.8 42 20-1 SPARE
<br /> OF LIGHTING SYSTEMS PER CGBSC SECTION 5.410.4. SUBTOTAL: 10.7 11.8 9.8 ABBREVIATIONS LIST
<br /> CONNECTED LOAD 32.23 KVA DEMAND KVA 37.2 kVA
<br /> FOOD SERV CE GENERAL N0TES 16. ELECTRICAL CONDUIT MUST IMMEDIATELY PENETRATE ROOF AND 25% OF LARGEST MOTOR 1.048 KVA DEMAND CURRENT 103.4 A A AMPERE PVC POLYVINYL CHLORIDE
<br /> RUN ALONG THE UNDERSIDE OF ROOF STRUCTURE. 25% OF CONTINUOUS LOAD 3.96 KVA A.F.F. ABOVE FINISHED FLOOR CONDUIT
<br /> 1. LIGHTING FIXTURES IN AREAS WHERE FOOD IS PREPARED OR OPEN
<br /> FOOD IS STORED OF WHERE UTENSILS ARE CLEANED SHALL HAVE 17. DURING THE COURSE OF TI CONSTRUCTION THERE ARE NO AL ALUMINUM (R) RELOCATEDw
<br /> C. CONDUIT SEC. SECONDARY
<br /> A SHATTER-PROOF LENS AND ARE READILY CLEANABLE. PENETRATIONS OF ELECTRICAL LINES AT THE EXTERIOR WALLS OF C.O. CONDUIT ONLY, WITH W
<br /> THE TENANT PREMISES. EXTERIOR WALL PENETRATIONS RELATING TYP. TYPICAL
<br /> 2. LIGHTING INTENSITY SHALL NOT BE LESS THAN 50 FOOT CANDLES TO TI WORK IS PROHIBITED. PULL LINE UG UNDERGROUND
<br /> AT 30" ABOVE FLOOR IN FOOD PREPARATION AREAS. CLG CEILING UON UNLESS OTHERWISE NOTED
<br /> 3. FOOD AND UTENSIL STORAGE ROOMS, REFRIGERATION STORAGE, (E) EXISTING V VOLTS U)GND. GROUND WP WEATHERPROOF Z
<br /> AND TOILET ROOMS SHALL NOT BE LESS THAN 10 FOOT CANDLES, KVA KILO VOLT AMP W WIRE 0
<br /> AT +30" ABOVE FLOOR. a
<br /> MSB MAIN SWITCHBOARD W/ WITH � Q
<br /> 4. ALL ELECTRICAL WORK SHALL CONFORM WITH THE CURRENT
<br /> EDITIONCALIFORNIAELECTRICAL CODE AND ALL STATE
<br /> PRI. PRIMARY XFMR TRANSFORMER � OAOCL REQUIREMENTSAND CODMAIN SWITCHBOARD 9V ^ B99
<br /> WIRE AND CONDUIT LEGEND O 0�
<br /> 5. VERIFY ALL OUTLET LOCATIONS PRIOR TO ROUGH-IN. Fu-G. PULL MAIN SECTION IUI�TRIBUTION w
<br /> V
<br /> I
<br /> SECTION SECTION CONDUIT RUN CONCEALED IN WALL OR ABOVE CLG.
<br /> 6. COORDINATE DEMOLITION WORK WITH ARCHITECTURAL DRAWINGS. - - - - - - UNDERGROUND CONDUIT. Q z
<br /> )1200/3 IPHOAOSE,M4 WIRE BUS. HOME RUN, NUMBER OF ARROWS INDICATE NUMBER OF CIRCUITS Z J CO
<br /> 7 FORVIDE ALL CIRC UIS TINNSCHEDULES PANELBOARDS,INDICATING
<br /> ON PANEL DOOR. CONDUCTORS DESCRIPTION
<br /> IN HOME RUN. NO CROSSBARS INDICATE (2)#12 �
<br /> CONDUCTORS IN 1 /2 CONDUIT. CONDUCTOR SIZE IS #12, _ z �
<br /> 8. USE ONLY INSULATED CONDUCTORS IN CIRCUITS. CONDUCTORS i I N I CONDUIT)200/3 LONGERCRIOSS ZE I BAR/INDICATES NE2" UNLESS UTRAL, SHORTSE ER DINDICATES Q C
<br /> SHALL BE SIZED PER NEC AND DRAWINGS (MINIMUM #12 COPPER). I G PHASE. ARC INDICATES GROUND.
<br /> MINIMUM CONDUCTOR INSULATION SHALL BE 'THW' OR THWN FOR O CONDUIT UP. � 0CONDUCTORS SIZE #6 AWG AND LARGER. NO ROMEX ALLOWED.
<br /> WHERE PVC CONDUIT IS USED, A GROUND WIRE SIZED PER NEC CONDUIT DOWN. O
<br /> ART. 250-45 (EQUIPMENT GROUND) SHALL BE PULLED. I SO CORD WHIP TO EQUIPMENT. SIZE AS MENTIONED o 3
<br /> oc U
<br /> 9. FINAL CONNECTIONS TO ALL DIRECT CONNECTED KITCHEN (E)SERVICE - - J (E)GND �� �N ON PLAN = C Q
<br /> EQUIPMENT SHALL BE WITH U.L. APPROVED LIQUID TIGHT CONDUIT, O 00
<br /> N
<br /> PROVIDED WITH GROUND WIRE SIZED PER NEC ART 250-95. CD
<br /> z V) Co
<br /> 10. CONDUIT INSIDE BUILDING SHALL BE EMT OR RSC. FLEXIBLE �� DATE 04/012022
<br /> CONDUIT ,AY BE USED WITH OWNER APPROVAL. ALL EXPOSED
<br /> FLEX CONDUIT SHALL BE SEAL-TIGHT OR EQUAL.
<br /> JOB 2227
<br /> 11. ALL JUNCTION BOXES SHALL BE 4" SQUARE, UNLESS NOTED SHEET TITLE
<br /> OTHERWISE. PANEL
<br /> E ELECTRICAL
<br /> 12. VERIFY MOUNTING HEIGHTS AND LOCATIONS OF ALL ELECTRICAL NOTES,
<br /> OUTLETS, J-BOZES, ETC. WITH OWNER PRIOR TO ROUGH-IN.
<br /> SUITE E SYMBOLS,
<br /> 13. ALL SWITCHES TO BE 36" MINIMUM, 48" MAXIMUM A.F.F.
<br /> 14. PROVIDE RECEPTACLE, DISCONNECT SWITCH, ETC. AS REQUIRED BY SCHEDULES
<br /> EQUIPMENT BEING INSTALLED. VERIFY RECEPTACLE & LEGEND
<br /> CONFIGURATION WITH FINAL EQUIPMENT SELECTION.
<br /> PARTIAL S NGSE LINE D AGRAM SHEET
<br /> 1
<br /> E1 . 0
<br />
|