WORK PLANS - Laserfiche WebLink

Home Browse Search

SHEET NOTES : O1 ALL DIMMING BALLAST/DRIVER SHALL COMPLY WITH T24, MINIMUM REQUIRED CONTROL STEPS AND UNIFORM ILLUMINANCE LEVEL. LED DRIVERS) TO MATCH OPERATION OF DIMMING CONTROL SWITCH FOR PROPER LIGHTING CONTROLS. PROVIDE 12 GA. VERTICAL STRUT SUPPORT PER U.B.C. O LIGHTING FIXTURES ARE TO BE APPROVED BY STANDARD #47-18, AT THE ARCHITECT. ELECTRICAL CONTRACTOR TO COORDINATE WITH ARCHITECT THE ACTUAL $11 0 0 0 12'-0" O.C. EACH WAY. LOCATION AND MOUNTING HEIGHT OF LIGHTING FIXTURES PRIOR INSTALLATION. DEG. 90 EG. O3 COORDINATE ALL LIGHTING CONTROLS WITH o G 0 AUDACY DIMMING PANEL CONTRACTOR/ Q EQUIPMENT VENDOR. Q < 1/2" $" 12'-0"O.C., MAX. 1/2" ACOUSTICAL TILE GENERAL NOTES : � � CEILING (MAX. 4 PSF.) NOTE . 4 -° MAX. NOTE : 1. ELECTRICAL CONTRACTOR SHALL VERIFY (E) FIELD CONDITIONS PRIOR TO O BID. ANY DISCREPANCIES BETWEEN DRAWINGS & (E) CONDITIONS FOUND o S O o ALL LIGHT FIXTURES SHALL BE ATTACHED TO TIE2 DURING INSTALLATION SHALL BE BROUGHT TO THE ENGINEER'S ATTENTION cV ( ) ADJACENT WALLT & SHOULD BE RESOLVED AT NO ADDITIONAL COST TO THE OWNER. CEILING MAIN & CROSS RUNNERS, THE CEILING GRID TO RESUST A HORIZONAL KEEP MAIN & CROSS RUNNERS FORCE EQUAL TO THE WEIGHT OF THE FIXTURES. �5�° AR�� 2. ALL WIRING TO BE COPPER "THWN," UNLESS OTHERWISE NOTED. SEE w F. sH, PANEL SCHEDULE FOR SIZING. 3/8" MIN. CLEAR OF OTHER WALLS FLUSH OR RECESSED LIGHT FIXTURES AND AIR 0o TERMINALS OR SERVICES WEIGHTING MORE THAN 3. ELECTRICAL CONTRACTOR TO SUPPLY OWNER WITH DRAWINGS OF THE HANGERS WIRES MUST BE FASTENED NO.C-33467 AS-BUILT CONDITION OF THE WIRING SYSTEM UPON COMPLETION. 56 POUNDS MAY BE SUPORTED ON HEAVY-DUTY RENO/31/2023 WITH NOT LESS THAN (3) TIGHT 4. ALL CONSTRUCTION OF THIS PROJECT SHALL CONFORM TO ALL LOCAL GRID, BUT MUST HAVE 2412 GA. SLACK SAFETY WIRESo 0 o TURNSSPLAY WIRES MUST HAVE 9 `4°�� CODES, ORDINANCES AND CURRENT ELECTRIC & BUILDING CODES. . FLUSH OR RECESSED LIGHT FIXTURES AND AIR (4) TIGHT TURNS FOR #12 GA. WIRES. TERMINALS OR SERVICES WEIGHTING MORE THAN 5. THE ELECTRICAL CONTRACTOR SHALL COMPLY WITH ALL LOCAL COUNTY, - STATE AND FEDERAL CODES, ORDINANCES, RULES AND REGULATIONS 4 12 GA. MIN HANGER WIRES N INCLUDING ALL REQUIREMENTS OF GOVERNING AGENCIES. ELECTRICAL ( ) GA.(MIN) 2X4' "T"-BAR SUSPENDED CEILING 56 POUNDS AND ALL FIXTURES AND AIR TERMINALS CONTRACTOR SHALL PAY ALL COSTS, ASSOCIATED WITH THE INSTALLATION, AT EACH SEISMIC BRACE. SYSTEM BY DONN CORP. OR OR SERVICES IN INTERMEDIATE DUTY GRID MUST Ld INCLUDING BUILDING APPLICATION FEES, ETC. APPROVED EQUAL. - I.C.B.O.#2244 BE INDEPENDENTLY SUPPORTED BY NOT LESS THAN > 13 6. ALL LIGHTING CIRCUITS SHALL BE RESPONSIBILITY OF THE ELECTRICAL (4) TIMES THE LOAD. Q N CONTRACTOR. IF ANY DISCREPANCIES WITH SWITCHING LAYOUT, VERIFY WITH TYPICAL CEILING PLAN TCEILING SECTION N ARCHITECT. LIGHTING SHALL MEET TITLE 24 REQUIREMENTS. U 0) 7. VERIFY THE TYPE OF CEILING SYSTEM WITH GENERAL CONTRACTOR OR LL CEILING CONTRACTOR. PROVIDE FIXTURES WHICH ARE COMPATIBLE WITH THE CEILING SYSTEM AND INCLUDE ALL REQUIRED MOUNTING ACCESSORIES AND HARDWARE. U Z 8. SUPPORT CEILING MOUNTED LIGHTING FIXTURES DIRECTLY FROM THE BUILDING STRUCTURE. DO NOT SUPPORT FIXTURES FROM PIPING, DUCTWORK OR ANY OTHER EQUIPMENT, OR SOLELY FROM THE SUSPENDED LL CEILING. _ 9. ALL LIGHTING FIXTURES SHALL BE NRTL LISTED. J Q 10. ALL SWITCH LOCATIONS SHALL BE VERIFIED WITH THE ARCHITECT PRIOR TOROUGH- O U N. 11. CONTRACTOR SHALL PROVIDE ADDITIONAL EXIT SIGN(S) IF REQUIRED BY (2) #8 SCREWS, WOOD or METAL z THE CITY FIRE MARSHALL INSPECTOR AT NO ADDITIONAL COST TO THE OWNER. PROVIDE SPLAY WIRES @ 12'-0" O.C. 8" IST, PURLIN, or SUB-PURLIN. MAX.. � 12. ALL EXIT SIGNS SHALL BE READILY VISIBLE FROM ANY DIRECTION OF IN BOTH DIRECTIONS AND IN PLANES EGRESS TRAVEL. PARALLEL TO RUNNERS. U 13. ANY FIXTURE SUBSTITUTION MUST BE APPROVED BY THE ARCHITECT OR 1/2" DIAM. RIDGID CONDUIT E.M.C. OWNER PRIOR TO BID. MAIN RUNNER ( ) \ ❑ 14. DRAWING SHOWS CIRCUITING AND SWITCHING REQUIREMENTS AND FIXTURE HANGER WIRE - ADD ONE PAIR % COMPRESSION STRUT. TYPES ONLY. VERIFY EXACT LIGHTING FIXTURES AND STANDARD SWITCHING OF BRACING WIRES PARALLA TO \45 DEG. LO WITH ARCHITECT AND OWNER PRIOR TO INSTALLATION. ALSO VERIFY WALL AT 8'-0" O.C. SPLICE AS NEEDED W/ 3/4" DIAM. X EXACT LIGHTING FIXTURES FINISH PRIOR TO INSTALLATION. CROSS RUNNER �_7 6" LONG CONDUIT and #8 MACHINE 15. PROVIDE 90 MINUTE MINIMUM EMERGENCY BATTERY PACK FOR EXIT SIGNS. SCREWS and NUTS. (SHALL COME TO FULL BRIGHT). NO. 12 GAGE SPLAY WIRE (4) IN ISI MAIN RUNNER 16. ALL QUANTITIES SHALL BE FIELD VERIFIED PRIOR TO BID. NOTIFY ENGINEER PLANE OF RUNNER VERTICAL ANGLE FOR ANY DISCREPANCIES IN DRAWINGS. OF 45 DEG. ALL WIRES SECURED CROSS-CUT BOTTOM OF CONDUIT 2" FROM � 17. FOR ELECTRICAL PENETRATIONS OF FIRE-RATED FLOOR/CEILING, PROVIDE TO RUNNERS APPROX. (1" DEEP) and FIT SNUG TO "T"-BAR PROTECTION PER 2019 CBC CHAPTER 7 RECESSED FIXTURES SHALL BE INTERSECTIONS. AT INTERSECTIONS. LISTED AND SHALL BE EITHER ONE OF THE FOLLOWING: Lu A. FIXTURES HAVE BEEN TESTED FOR USE IN FIRE-RESISTANCE-RATED NOTE: ASSEMBLIES OR ACOUSTIC CEILING TILE B. FIXTURES SHALL BE PROTECTED WITH A LISTED FIRE-RATED LIGHT ADDITIONAL WIRE AT EACH CORNER NOTE: o COVER. OF LIGHTS DIAGONAL WIRE EVERY PROVIDE COMPRESSION STRUTS at 18. INSTALL GROUNDED (NEUTRAL) CONDUCTORS OR PROVIDE RACEWAY TO 144 SQ. FT. WITHIN 2" OF CROSS 12'-0" O.C. IN EACH DIRECTION for ALL SWITCH LOCATIONS AS PER 2019 C.E.C. ARTICLE 404.2. CONTINUOUS ANGLE WITH RUNNER CONNECTED TO STRUCTURE 144 SQ. FT. and WITHIN 6'-0" of 19. ALL CONTROLS AND SWITCHES INTENDED TO BE USED BY OCCUPANT OF SELF-TAPPING SCREW AT ABOVE AT THE HORIZON IN (4) THE WALL. STRUT TO BE FASTENED THE ROOM OR AREA TO CONTROL LIGHTING AND RECEPTACLE OUTLETS, DIRECTIONS, 90 DEG. APART WITH i AT CONVERGENCE of THE SPLAYED z APPLIANCES OR COOLING, HEATING AND VENTILATING EQUIPMENT, SHALL EACH WALL STUD. o LOCATED NO MORE THAN 48 INCHES MEASURED FROM THE TOP OF THE THE FIRST POINT WITHIN 4 FROM WIRES PER U.B.C. (e,7)-2. BOTTOMONO ORHDEVICE UNCTBOX ION ORNOR DEV CE BOX ABOVE INCHES THE FINISHED EDTO FLOOR. E I .C.B.O. #E 82244 WALL ,C,B,Q, #E 82244 THE WALL r� U U) 20. LIGHTING FIXTURES INSTALLED IN A SUSPENDED CEILING SHALL BE FASTEN I .C.B.O. #ER2244 0 , TO THE CEILING FRAMING MEMBER AT ALL FOUR CORNERS WITH SCREWS AND ATTACHED 12 AWG CEILING WIRES TO THE LIGHT FIXTURE AT DIAGONALLY OPPOSITE CORNERS AND TO THE STRUCTURAL CEILING. w 21. THE MEANS OF EGRESS ILLUMINATION LEVEL SHALL NOT BE LESS THAN 1 Q FOOT-CANDLE (11 LUX) AT THE WALKING SURFACE LEVEL, IN THE EVENT OF POWER SUPPLY FAILURE, AN EMERGENCY ELECTRICAL SYSTEM SHALL AUTOMATICALLY ILLUMINATE THE FOLLOWING AREAS: A. AISLES AND UNENCLOSED EGRESS STAIRWAYS IN ROOMS AND SPACES THAT REQUIRE TWO OR MORE MEANS OF EGRESS. B. CORRIDORS, EXIT ENCLOSURES AND EXIT PASSAGEWAYS IN BUILDINGS REQUIRED TO HAVE TWO OR MORE EXITS. C. EXTERIOR EGRESS COMPONENTS AT OTHER THAN THE LEVEL OF EXITS DISCHARGE UNTIL EXIT DISCHARGE IS ACCOMPLISHED FOR BUILDINGS ISSUE: 15 APRIL 2022 REQUIRED TO HAVE TWO OR MORE EXITS. D. INTERIOR EXIT DISCHARGE ELEMENTS, AS PERMITTED IN SECTION PROJECT NO: 1024.1, IN BUILDINGS REQUIRED TO HAVE TWO OR MORE EXITS. E. EXTERIOR LANDINGS, AS REQUIRED BY SECTION 1008.1.5., FOR EXIT FILE: DISCHARGE DOORWAYS IN BUILDINGS REQUIRED TO HAVE TWO OR DRAWN BY: W.N.R. MORE EXITS. CHECKED BY: 22. ELECTRICAL PLANS ARE INTENDED TO SHOW, IN A GENERAL WAY, THE APPROXIMATE LOCATION AND LOADS OF THE INTENDED FIXTURE AND EQUIPMENT. EXACT LOCATIONS AND MATERIALS SHALL BE DETERMINED IN THE FIELD BY THE INSTALLING CONTRACTOR AND SHALL CONFORM TO THE PROVISIONS AS SET FORTH IN THE 2019 EDITIONS OF THE CALIFORNIA ELECTRICAL CODE, CALIFORNIA ENERGY CODE AND CALIFORNIA GREEN BUILDING CODE. 23. PROVIDE A SEPARATE NEUTRAL CONDUCTOR FOR EACH AND EVERY PHASE CEILING / LIGHTING (LINE) CONDUCTOR; TO COMPLY WITH 2019 CEC ARTICLE 210.4 FOR DETAILS MULTI-WIRE CIRCUITS AND TO PERMIT INDIVIDUAL OPERATION/CONTROL OF AND EACH BRANCH CIRCUIT OR PROVIDE TIE HANDLE ON BREAKERS TO SUIT SCHEDULE SINGLE NEUTRAL ON MULTI-CIRCUITS HOMERUNS- NEUTRAL MUST BE MINIMUM 10 AWG ON MULTI CIRCUITS. 24. THE CONTRACTOR/INSTALLER SHALL IMMEDIATELY NOTIFY IN WRITING THE PROJECT OWNER AND M+R (CONSULTANT) FOR CLARIFICATION OF ANY DISCREPANCY IN THIS DESIGN PACKAGE OR ANY CONFLICT WITH OTHER TRADES PRIOR TO COMMENCING THE WORK. ALL WORKS, SERVICES, INSTALLATION OR SUPPLY OF EQUIPMENT AND DEVICES RESULTING FROM ALTERATION OR DEVIATION FROM THIS DESIGN AND ITS INTENT WITHOUT A-5 . 1 THE WRITTEN NOTIFICATION TO AND APPROVAL FROM M+R SHALL BE ON THE ACCOUNT OF THE CONTRACTOR/INSTALLER.