COMPLIANCE INFO_2023 - Laserfiche WebLink

Home Browse Search

CE co � p f Amershield al z i Yl' y PRODAJ Surface Preparation STEEL - Mill scale and rust must be removed . Abrasive blast Shipping Data hot-rolled steel to Sa 2* or SSPC SP6** and rusted and pitted steel to Sa 2Y2* or SSPC SP10** (ISO 8501 -1 ). Packaging ALUMINIUM - Remove oil , grease or soap film with neutral resin . . . . . .. . . . .. . . .. .. . . . . ..4 . 004 .... . ... 3.21 (0 .85 gal) in 51 can detergent or emulsion cleaner; blast lightly with fine abrasive. 161 - in 201 can cure . . . . . . . . .. . . . . .. . .. . . . . . . . . . . ... . . . . . . GALVANISING - Remove oil or soap film with neutral detergent 0.81 in 1 I can . . . .. . . . .. . . . 4 I in 5 I can or emulsion cleaner; treat with Amercoat 59 or blast lightly with "" " " ' " "" " fine abrasive. Shipping weight DIMETCOTE - Wash off water soluble contaminants; remove resin . . . . . . . . . . . .. . . ... . .. . . . . . . . . . . . . . . . approx. 4.5 kg and 17.5 kg oil , grease, etc, with a neutral detergent or emulsion cleaner. cure . ... . . . . . ..... . .... . . .. . .. . . . . . .. . . . . approx. 1 kg and 3 .4 kg Solvent wipe is not satisfactory. CONCRETE - Clean concrete and masonry surfaces, abrasive Shelf life . .. . .. . ...... . .. . . . . . . . . . . . ... . . . 1 year from shipment date when blast (ASTM D4259). Fill concrete voids with Nu-Klad 1141 stored indoors in unopened , COATED SURFACE - Clean by high pressure ( 1000 psi = 70 original containers at 5 to 40°C bar or more) water blast, sweep blast (SSPC SP-7**), solvent (41 - 104 ° F), emulsion cleaning (SSPC SP- 1 **) or power tool cleaning (SSPC SP-3** ). Surface must be clean , dry and free of oil, grease , dirt or other contamination . Apply test patch to confirm compatibility and adhesion . Swedish Standard SIS 05-5900-1967 ** Steel Structures Painting Council Specification Application Procedure Amershield is packaged in the proper mixing proportions of resin and cure. Resin 3.2 and 161 in 5 and 201 can Cure: 0.8 and 41 in 1 and 5 l can 1 . Flush equipment with recommended cleaner before use. 2. Stir resin thoroughly, add cure and mix until uniform . Do not mix more material than will be used within potlife time. Mixing ratio is 4 parts resin to 1 part cure by volume. 3 . if thinning is necessary for workability thin with no more than 15 % vol . of Amercoat 920. For airless spray normally no thinning is required . 4 . When applying by spray, adjust pressures for equipment configuration and environmental conditions to ensure proper atomization . 5. Apply a wet coat, making parallel passes and overlapping each pass 50% . NOTE : When applying directly over inorganic zinc at full thickness, bubbling may occur. Use a mist coattfull coat application procedure . 6 . Application at 160 pm wet film thickness (unthinned ) will normally provide 125 pm dry film . 7 . Moisture sensitive - Keep cure container tightly closed . Repeated moisture exposure will cause gelation and gassing ; handle bulged containers with caution , lids may eject forcibly. 8. Check thickness of dry coating with a non-destructive dry film thickness gauge, such as Mikrotest or Elcometer. If less than specified thickness, apply additional material as needed . 9. In confined areas ventilate with clean air during application and drying until all solvents are removed . Temperature and humidity of ventilating air must be such that moisture condensation will not form on surface. 10 . Clean all equipment with recommended cleaner immediately after use or at least at the end of each working day or shift. When left in spray equipment, Amershield will cure and cause clogging . Page 3 of 4 Revision date: 09-11 -2005