COMPLIANCE INFO_2023 - Laserfiche WebLink

Home Browse Search

GULF COAST PAINT MFG.q INC. APPLICATION PROCEDURE CM-15/page,l AidessSpray Greco Conventlonalspray MINIMUM DeVilbiss Gun Silver Plus Gun RECOAT Pump 33:1 Extreme Fluid Tip MBC or JGA Tip Range .019 to .023 Air Cap D Hose 3/8 inch I. D, Atomizing Pressure 64 Pressure 2400 to 2700 psi Hose 60 psi Filter Size 60 Mesh Y= inch I.D. Roller— Use a 3/8" —'/2' nap, phenolic core, shed resistant roller cover. Roll in the same direction always keeping a wet edge. Do not over roll product. Brush — Use pure bristle brush. When spraying, use a 50% overlapping crosshatch pattern to minimize the occurrence of pinholes. Do not apply to surfaces below 45°F or above 120°F. Do not apply over dew or frost. The surface should be dry and at least 5°F above the dew point. Times may be longer for thickness above 5 dry mils. For safety and proper product curing, good ventilation is necessary when painting indoors or in confined areas. Be sure the batch numbers are all the same to pro- vide uniform color. Epoxy coatings may yellow or darken during application and after final cure. This will af- fect the color but will have no effect on the performance of the product. Heaters that emit carbon dioxide and carbon monoxide can cause the coating to yellow. For maximum interior gloss and color retention apply one (1) topcoat of PC -270 Polyester Epoxy. For maximum exterior gloss and color retention apply a topcoat of CT -370 polyurethane. CAUTIONS CM -15 is flammable. Keep away from all sources of ignition during mixing, application and cure. CM -15 Hardener is corrosive. The Hardener and Base can cause eye and skin burns as well as allergic reactions. Use goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing. This product is sold without warranty as to performance expressed or implied. Users are urged to make their own tests to determine the suitability for their particular conditions. SEE SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.FOR PROFESSIONAL AND INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN. NOT FOR RESIDENTIAL USE Technical Bulletin GCP-15 Rev. 10/2019 Phone: 251-964.7911 30075 County Rd. 49, Loxley, AL 36551 Fax: 251.964-7918 www.qulfcoastpaint.com e-mail: !E!2@-qulfcoastpaint.com RECOAT TIME MINIMUM MAXIMUM TEMPERATURE TACK FREE RECOAT RECOAT / 907 1 - 2 hours - 5 6 hours 3 days 75°F 3 -4 hours 7.8 hours 7 days 50°F 8-12 hours 36-48 hours 10 days Times may be longer for thickness above 5 dry mils. For safety and proper product curing, good ventilation is necessary when painting indoors or in confined areas. Be sure the batch numbers are all the same to pro- vide uniform color. Epoxy coatings may yellow or darken during application and after final cure. This will af- fect the color but will have no effect on the performance of the product. Heaters that emit carbon dioxide and carbon monoxide can cause the coating to yellow. For maximum interior gloss and color retention apply one (1) topcoat of PC -270 Polyester Epoxy. For maximum exterior gloss and color retention apply a topcoat of CT -370 polyurethane. CAUTIONS CM -15 is flammable. Keep away from all sources of ignition during mixing, application and cure. CM -15 Hardener is corrosive. The Hardener and Base can cause eye and skin burns as well as allergic reactions. Use goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing. This product is sold without warranty as to performance expressed or implied. Users are urged to make their own tests to determine the suitability for their particular conditions. SEE SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.FOR PROFESSIONAL AND INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN. NOT FOR RESIDENTIAL USE Technical Bulletin GCP-15 Rev. 10/2019 Phone: 251-964.7911 30075 County Rd. 49, Loxley, AL 36551 Fax: 251.964-7918 www.qulfcoastpaint.com e-mail: !E!2@-qulfcoastpaint.com