Laserfiche WebLink
5} Dtpatick number(XJ=82" top Of the Face Seal Adaptor M the spill container to the <br /> Tank diameter(Ya 92" boltum of ttw tank IDim.'81, <br /> (Y}-V)=M (92' -2'= 1(') 11MPMANT,Irapea the riser for an io n rnate^ <br /> P� Y �9 <br /> (7 = 14" vial. Over spray from tank relining or any irttemdl bums <br /> d) W-2'—C (1 o"-2' 8') Inside of pipe must be removed prior to In5taila tion. <br /> C=fr failure to havean unobstructed user pipe may prevent <br /> T) is 8'less than 6-112`7 prow Insullation and operation of the valve. The <br /> 71 SO is designed for InstaAMon Into schedule 40 riser <br /> NO Measure thr distance from the top of the FSA- pry The 71 SO cannot be installed into schedule 80 <br /> 400 Face Seal Adaptiar installed on the riser pipe riser plm' <br /> to the inside,top lip of the storage tank and ob- STXP 2: MUKTHE TUBE <br /> tai n measurement M. Use tate result from Step I and l'rIIQW M LOCATE THE <br /> AOSPi ON OF THE 7 TSO AT ps%TANK CAPA rry to <br /> 1J peer tube length =C+(Ay mark the Upper tube. Measure the distance from the <br /> SL <br /> where the upper tube and vahre body mem Use <br /> For testable models only,ending in"T': fJpper Tub* a tape measure to mark the calculated upper tfbe <br /> i angth=C + (Al-1-117" Length onto the upper-tube. See Rgure 2- <br /> ASSEItMLY DASMUCTIONS Tape rneea,re <br /> IMPORTANT. 1=ach of the nu mbered steps in the in- <br /> stallation instructions are designed as a CHECK LIST to <br /> ensure proper Installation and trflublefreeoperation of <br /> the OPW 21SO Overfill Prevention Valve. <br /> Read and follow these steps carefully,checking tt*m Rl.w Pp <br /> e <br /> offas y'oV prvoeed. *11h Fere (A) <br /> beer A d4 pilar To Ts Nc <br /> Figure rtumtJers correspoc►d to step numb@rsfor easy <br /> Top I.CI.I TotT�rnk <br /> reference. <br /> STEP 1: [MEASURE <br /> Install tate OPW Face Sear Adaptor and the OPW TAmad- <br /> on 5gila Container on ove Fill Riser[Refer to the fnsWa- <br /> tlon Instnxtions Supplied with the So Contalner). In- Fjgarr 7 <br /> sent a tape measure through the riser pipe and hook It _ <br /> under the lnside of thie tank in the Iengthwise direction, <br /> Measure tttie distance from the top of the Face Seat <br /> Adaptor threads Inslde the base of tete spill container <br /> bucket just below the drain valve outlet window to the 4,tG''1. <br /> inside,top lip of the storage tank(Dim.W)(Sae Figure NOT <br /> 1 WA1. <br /> The top range on the 71 SO velli rest on the Face Sea! <br /> Adaptor just below the drain valve outlet,and be <br /> lacked in place between the Face Seat Adaptcw and the a <br /> 4'nipple that is installed in the spill container wirlh the Ovr�tslr�er <br /> Jack Screw Kit(See Figr 1 A). (For riser pipe configura- Jack Screw <br /> tions other than that shown,consult instxladondravr- K8 <br /> ings or use other necessary meads to measure Dirnen. ira"Swwifion Jack <br /> slon`A-). (TOP 0 Faw <br /> Usiny a tape measure,measure the distance tram the 711 so Adepior <br /> F rVwv 7A s <br />