Laserfiche WebLink
3'-0"PLYWOOD WITH WHITE PLASTICLAMINATE ON OUTER FACEBLOCKING AS REQUIREDFRPCERAMIC TILET-1QTB-1Scale: 1-1/2" = 1'-0"6" S/S BASEPOWER SET FASTENERS,TYP.5/8" CEMENT BD. OVER3-5/8" MTL. STUDS, 1'-0"O.C.2"x2" STAINLESS STEEL LEGSUPPORTS3/4" F.T. PLYWOODS-12'-10"2"SS-1ANCHOR RUNNER TRACK W/ HILTI X-C22P8TH LOW VELOCITY POWDER ACTUATEDANCHORS 0.145Ø x 3/4" LONG AT AT 16"O.C. (ICC-ES REPORT #ESR-1663)Scale: 1-1/2" = 1'-0"DINING5/8" CEMENT BD. OVER3-5/8" MTL. STUDS,3 5/8" x 20 GA. MTL. STUDS @ 12"O.C. (ICC REPORT #ESR-3064P)ANCHOR STUDS TO TRACK W/ #10SHEET MTL. SCREW EACH SIDE.QTB-16" S/S BASECOVED QUARRY TILEBASE BASECOOK LINEAREASEE ELEVATIONS FOR FINISHESSS-1(2) LAYER OF 3/4" F.T.PLYWOOD2"STAINLESS STEEL CAPSNEEZE GUARD. SEE SNEEZE GUARDDETAIL ON THIS SHEET℄STUDS8"BLOCKING AS REQUIRED5'-0"3'-4"2"1'-6"75°6" S/S BASEDINING5/8" CEMENT BD. OVER3-5/8" MTL. STUDS,3 5/8" x 20 GA. MTL. STUDS @ 12"O.C. (ICC REPORT #ESR-3064P)ANCHOR STUDS TO TRACK W/ #10SHEET MTL. SCREW EACH SIDE.QTB-1COVED QUARRYTILE BASE BASEANCHOR RUNNER TRACK W/ HILTI X-C22P8TH LOW VELOCITY POWDER ACTUATEDANCHORS 0.145Ø x 3/4" LONG AT AT 16"O.C. (ICC-ES REPORT #ESR-1663)Scale: 1-1/2" = 1'-0"COOK LINEAREASEE ELEVATIONS FOR FINISHESSS-1(2) LAYER OF 3/4" F.T.PLYWOOD2"SS-1STAINLESS STEEL CAP8"MATRIX SERIESFLUORESCENT LIGHTFIXTURE KIT SUPPLIEDBY ENGLISHMANUFACTURINGSNEEZE GUARD. SEE SNEEZEGUARD DETAIL ON THIS SHEET℄STUDSBLOCKING AS REQUIRED4'-6"3'-4"2"1'-0"75°11BRACE TOP OF WALL W/ANGULAR 3 5/8" 20 GA.STUD BRACING @ 48" O.C.STAGGERED W/ (3) #10'sEACH END. WHERE BRACEDOES NOT ALIGN W/STRUCTURAL MEMBER GC TO COORDINATE WITHOUT ATTACHING TO ROOF DECKINGSUSPENDED CLEANABLETILE CEILING5/8" GYPSUM BOARDBOTH SIDESSEE PARTITION AND FINISHPLAN FOR WALL FINISH.COVE BASEANCHOR TRACK TO SLABW/ HILTI .145 SHOT PINS(OR EQUAL) @ 48" O.C.TOP OF SLABCEILING HEIGHT VARIES6"3 5/8" 20GA METAL STUDS @ 16" O.C., OR 6" 20GA METAL STUDS, REFER TO PLANSECURE STAINLESS STEEL END CAPTO WALL WITH SILICONE CAULK.2"WALL FINISH ON 5/8" GYP. BD. ON 3- 5/8"20 GA. MTL. STUDS @ 16" O.C. - TYP.FLOOR TO CEILING STAINLESSSTEEL END CAP CG-02VARIES W/WALL FINISHFLOOR TO CEILING STAINLESS STEELCORNER GUARD CG-012"WALL FINISH ON 5/8" GYP. BD. ON 3- 5/8"20 GA. MTL. STUDS @ 16" O.C. - TYP.SECURE STAINLESS STEEL CORNERGUARD TO WALL WITH SILICONE CAULK.2"It is the responsibility of the ConstructionManager/General Contractor and allSub-Contractors to verify all dimensions andaccept conditions of prior work by relatedtrades before proceeding with any work.DateDrawn ByScaleSeal:Project TitleProject AddressProject NumberDrawing Title and NumberMAIN OFFICE:1 HUNTINGTON QUADRANGLESUITE 2C03MELVILLE, NY 11747P: 631.226-7700 F: 631.226.7175Issued:Check ByOwner:AS SHOWNSTAFFCM© Copyright 2018: RGBK, INC.CharleysRobert Cheung2043 Limewood Drive,San Jose, CA 95132Stockton, CAWM15543223 E Hammer Ln,Stockton, CA 95212WM1554WALL TYPES ANDMILLWORK DETAILSA3.007-22-20213SALES COUNTER SECTION DETAIL4LOW WALL SECTION DETAIL5LOW WALL SECTION DETAIL (2)RESTROOMS PROVIDED BY WALMART1TYPICAL INTERIOR PARTITIONSCALE: 3" = 1'-0"2STAINLESS STEEL END CAP DETAILSCALE: 3" = 1'-0"6STAINLESS STEEL CORNER GUARD DETAILNOT USEDNOT USEDRev.No.DescriptionDateIssued for Permit08-23-2021