WORK PLANS - Laserfiche WebLink

Home Browse Search

ArmorSeal ARMORS EAL HS POLYURETHANE Heavy FLOOR ENAMEL Duty Floor Coatings PART A B65-220 SERIES PART B B65V220 HARDENER Revised: March 24, 2022 APPLICATION BULLETIN 8.46 APPLICATION PROCEDURES Surface preparation must be completed as indicated. Mix contents of each component thoroughly with low speed power agitation. Make certain no pigment remains on the bottom of the can. Then combine two parts by volume of Part A with one part by volume of Part B. Thoroughly agitate the mixture with power agitation. Allow the material to sweat-in as indicated. Re-stir before using. If reducer is used, add only after both components have been thoroughly mixed. If an anti-slip finish is desired, the additive is mixed into the final coat just prior to application. (EXCEPTION: If anti-slip is desired with Clear finish, it should be hand broadcast). A 3/4" pile roller is recommended for the final coat when anti-slip aggregate is used. Apply paint at the recommended film thickness and spreading rate as indicated below: Recommended Spreading Rate Der coat: Minimum Maximum Wet mils (microns) 3.0 (75) 4.5 (112) Dry mils (microns) 2.0 (50) 3.0 (75) —Coverage sq ft/gal (m2/L) 380 (9.3) 570 (14.0) Theoretical coverage sq ft/gal (m2/L) @ 1 mil / 25 microns dft 1136 (27.8) NOTE: Brush or roll application may require multiple coats to achieve maximum film thickness and uniformity of appearance. Drying Schedule @ 3.0 mils wet (75 @ 77F/25°C microns): @ 50°F/10°C @ 100°F/38°C 50% RH To touch: 16 hours 2 hours 30 minutes To handle: 24 hours 10 hours 2 hours foot traffic: 24 hours 12 hours 8 hours heavy traffic: 5 days 72 hours 48 hours To recoat: minimum: 24 hours 12 hours 2 hours maximum: 3 days 48 hours 24 hours To cure: 7 days 7 days 5 days If maximum recoat time is exceeded, abrade surface before recoating. Drying time is temperature, humidity and film thickness dependent. Pot Life: 5 hours 4 hours 45 minutes Sweat-in-Time: None required Application of coating above maximum or below minimum recommended spreading rate may adversely affect coating performance. CLEAN UP INSTRUCTIONS Clean spills and splatters immediately with Reducer R6K30 or R7K225. Clean tools immediately after use with Reducer R6K30 or R7K225. Follow manufacturer's safety recommendations when using any solvent. DISCLAIMER The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin- Williams representative to obtain the most recent Product Data Information and Application Bulletin. PERFORMANCE TIPS Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas. When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle. Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profile, roughness or po- rosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive film build. Excessive reduction of material can affect film build, appearance, adhesion and potentially cause color float. Do not apply the material beyond recommended pot life. Do not mix previously catalyzed material with new. In order to avoid blockage of spray equipment, clean equipment before use or before periods of extended downtime with 'Reducer R6K30 or R7K225. Mixed coating is sensitive to water. Use water traps in all air lines. Moisture contact can reduce pot life and affect gloss and color. Additive of anti-slip aggregate produces only a light nonslip tex- ture. Product should not be used in place of a nonskid finish when safety is a concern. Material cannot be sprayed if anti-slip aggregate is used. Shot blasted floors will require a high build primer. When rolling this product, always maintain a wet edge to avoid roller marks. Rolf as close to any cut-in areas as possible to eliminate visual imperfections. Roller application must be from a roller tray, not by pouring the material onto the surface. Coated surfaces may discolor under tires due to tire plasticizer migration. Refer to Product Information sheet for additional performance characteristics and properties. SAFETY PRECAUTIONS Refer to the SDS sheet before use. Published technical data and instructions are subject to change without notice. Contact your Sherwin-Williams representative for additional technical data and instructions. WARRANTY The Sherwin-Williams Company warrants our products to be free of manufacturing defects in accord with applicable Sherwin-Williams quality control procedures. Liability for products proven defective, if any, is limited to replacement of the de- fective product or the refund of the purchase price paid for the defective product as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY SHERWN-WILLIAMS, EXPRESSED OR IMPLIED, STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER- CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. www.sherwin-williams.com/protective