Laserfiche WebLink
fESTAGLE PflOCEDURI: ONLY, FOR STANDARD MOEP- <br />ELS. P WEW TO NEXT YAGE. <br />Pro &P i7= 11N3111LL MULWE'{ ADAP'T�GR ASST <br />Taut Cable tttiru threads in Inlet tube and outthru cable <br />port cxn #de of inlet tube. Thread The socket acla ptor <br />assembly finge=r tight into the iniet <br />tube. Now the ea- <br />ble port on the inlet tube must be in llrte with the float <br />as shown pmviously in Figure 8A - <br />adaptor , <br />assembly <br />K, Cable <br />port <br />i <br />T <br />STEts �'f'a PAS$ C/iiBtE Tt�LU PEtl�tLli`E <br />Prss cable ihru ferrule. Loop 4 a, te.anal then pass cable <br />back Thru ferrule. Keep ferrule loose until cable lenwh <br />Is cs~tl nt!d in the next step. Note: if cable lend frays <br />it nvy bo ne<essary toy trim the cable aga In W pass thru <br />ferrule. <br />11$` rnarrclr�l r� <br />\` f <br />�! t <br />Aller <br />strp3T Loop <br />Fi�un� 1T <br />STEP 3T: DETERIMIHE OWLE LENGTH <br />flun cable along upper tube artd .over the top plate On <br />the Hutt bracket as shAwn. With th4e ticw in the down <br />paution (as shvwn in Flgum 3T) 01W loop in table with <br />rivet and top hole in float bracket. Use tete rhtet as a <br />template to size the loop in the cable and pull cable <br />tight and crimp ferttte with crimpirg tool / pliers onto <br />cable at this location. Trim excess cable with wire cut- <br />ter / scissor, For reference, fmm the sew where the <br />upper tube and valve bandy meet to the end of the cabi<e <br />(ter ramming will require approximm* 350 of cable. <br />STEP 4r: A,Ti'At�U �� TD FLC}AT DO Arm" <br />insure cable Is over the float bracket, tlsirxl the sup- <br />plied rivet align long in cable with rap Me in #last <br />bracket and pass rtvtt thnf cable 3aop wd floe bracket <br />hole. Using rivet too) for 1/ir dia marrdmJ attach rivet <br />an[1 cable to the float bracket. Spee Iasi page for list of <br />replarem+entcable parts, <br />�-` Attach rivet totop hots <br />am SIT �- <br />STe� sr: ENs�IPIJI: t�oot�ttt cr�a;~.>a oPER►wr14M <br />Ur,tfuea+d the vacic�x a+da assembly from the inlet <br />tube ar d onsur£ float and poppet move freely when <br />,ork&T adaptor assembly is pulled an. It should only <br />require 3` to 4N of rnrnrement in oar to apctuate the <br />floaL and poppet. Thread socket adaptorassombly fin- <br />gerUght into in* tube af#ertesOrMg. <br />Cable <br />over <br />float <br />bracket <br />. <br />�_- <br />STEP 4r: A,Ti'At�U �� TD FLC}AT DO Arm" <br />insure cable Is over the float bracket, tlsirxl the sup- <br />plied rivet align long in cable with rap Me in #last <br />bracket and pass rtvtt thnf cable 3aop wd floe bracket <br />hole. Using rivet too) for 1/ir dia marrdmJ attach rivet <br />an[1 cable to the float bracket. Spee Iasi page for list of <br />replarem+entcable parts, <br />�-` Attach rivet totop hots <br />am SIT �- <br />STe� sr: ENs�IPIJI: t�oot�ttt cr�a;~.>a oPER►wr14M <br />Ur,tfuea+d the vacic�x a+da assembly from the inlet <br />tube ar d onsur£ float and poppet move freely when <br />,ork&T adaptor assembly is pulled an. It should only <br />require 3` to 4N of rnrnrement in oar to apctuate the <br />floaL and poppet. Thread socket adaptorassombly fin- <br />gerUght into in* tube af#ertesOrMg. <br />