INSTALL_2024 - Laserfiche WebLink

Home Browse Search

"1/4" fuel hose capped"—clarify if this is a fuel hose or a vacuum hose. Also on C6 detail "opening through primary wall"—no openings through the primary wall are allowed. Contractor will do this. EHD: Still need. 7. Identify the means to check communication for vacuum monitoring on piping secondary containment on page T&L2, UDC detail. See details EHD: corrected. 8.T&L3, detail 5, and T&L4- sump liquid sensor is not shown at the lowest sump point Revised location EHD: corrected. 9. Provide cut sheets for tank sumps and penetrations (including electrical) Oand for all UDC and Vent sump penetrations, leak detectors, overfill. See attached EHD: some cut sheets were provided but some are still missing, like tank sumps, vent sump, all UDC etc. For example, B1000 cut sheet was included for UDCs, however, the UDC part number listed on the plans doesn't match the provided UDC cut sheet. Please provide cut sheets for all the parts listed on the parts list. 10.The provided parts order list shows 2 tanks with 2 compartments each, plans show two compartment and three-compartment tanks, clarify and send in the corrected parts order list Revised parts list tanks, 100, 103 see T&L7 and 7.1 EHD: corrected. 11. Provide installer/tester certifications for FE Petro and Flex-ing (Fireflex) When we have a contractor EHD: still need this. 12. Provide B-20 compatibility information for all components in contact with B-20 See attached sheets. EHD: it's unclear where this documentation is included, please provide a separate file titled compatibility. 13.T&L4, the 6K/24K fill sump on 24K tank chaise penetration is not located at sump wall but is located inside the sump. Also, 6K super tank fill sump has an unlabeled penetration and pipe with what appears to be an electrical connection that terminates at the bottom of the sump. Revised details EHD: corrected. 14.T&L4, details A3 and A4 don't show chaise lines Added line. EHD: corrected. 15.T&L6, Need vacuum communication details. Added to details EHD: end-of-the-line vacuum communication provisions couldn't be located on UDC (T&L6), please point them out. 16. Bravo deflector plates are proposed on T&L6, submit bravo cut sheet and installation information and indicate on plans how they will be installed. Revised to tank manufacturer. EHD: corrected, per plans no deflector plates will be installed, if they will be installed- provide the installation details. 17. No chaise piping is shown to 20K diesel fill sump for vent piping run to vent transition sump. No chaise piping is shown for this tank on T&L1, update all necessary sheets as well as vacuum zone details, piping length and volumes. See T&L1 and tanks sections. EHD: corrected. 18. It's unclear if the master/satellite piping is VPH-monitored double wall piping. Provide a revision that illustrates, that master/satellite dispenser piping is double wall and VPH monitored. No monitoring details or vacuum hose connections are shown inside the UDCs x-sections for master/satellite dispensers. Update vacuum zones to include pipe lengths and volume details. Revised the details to show this. YES THEY ARE MONITORED EHD: corrected. 19. Not all parts on the list parts and their diamond reference numbers on each respective plan sheet match across the plans. For example, part 402 listed multiple times on T&L2 and appears to point to a Bravo sump penetration, is listed as Fire Flex on the parts list located on page T&L7. To avoid any plan review delays, ensure that all parts lists are accurate on the future submittals (pages T&L7 and T&L7.1) and reference accurate parts on all the plan sheets. Done EHD: some issues are still observed with this item. The following list is not all-inclusive and some other issues may exist with the parts list reference system, here are some of the examples. Part number 823 (on the parts list) is listed as 23 each, this part is a combination of 806 and 815 parts for a complete 823 assembly. However 806 part is also listed separately as 23 each as well as part 815 listed at 23 each- please clarify how many of these will be installed. Part 400 is listed on several plan sheets, but not included on the parts list. Please provide an explanation on part 209 "single port spill platform" installed on the vent sump.Three parts 218 (vent sumps containment boxes) are listed on the parts list, but only one vent sump is proposed on the plans. Part 229 on sheet T&IL3 points to the overfill prevention drop tube, part 229 on parts lists is identified as a manhole cover. Also, 6 Wayne ovation 2