COMPLIANCE INFO_2024 - Laserfiche WebLink

Home Browse Search

P.O. BOX 1928 BENICIA, CA 94510 TEL 707 346 5058 FAX 707 922 2284 PEI Qualifications and Certifications ENGINEERING & INSPECTION, INC. WWW.POWERSEI.COM Powers NDE Qualifications rev4 Page 1 of 1 © 2024 PEI Inc. American Society of Non-Destructive NDE Testing Corporate Certification This is to certify that: Aiken Arriola has successfully completed the NDE training detailed below Date of Completion: 1/19/2024 Expiration Date: 1/19/2029 This training and field experience certifies that Aiken Arriola has met the requirements of Powers Engineering & Inspection's "Nondestructive Examination Written Practice No: WP-001, Rev 3" and ASNT SNT-TC-1A: Ultrasonic (UT) Magnetic Particle (MT) Penetrant Test (PT) Bubble Test (BT) Visual Test (VT) Level II Level II Level II Level II Level II Powers Engineering & Inspection (PEI) Company Training is under the guidance of World Spec NDT Training and PEI NDT Qualification Procedures. To qualify, the following criteria were met: 1.) The minimum hours required per method in theory Training and Testing per ASNT SNT-TC-1A "Nondestructive Examination Written Practice No: WP-001, Rev 3" 2.) Completion and Pass of Written Test for each method 3.) Completion of general training in NDT Principles, Applications, Materials & Process 4.) Minimum field hours per method as required by ASNTSNT-TC-1A. 5.) Annual Visual Acuity test. In addition, in accordance with PEI corporate procedures and standards, Aiken Arriola has completed and passed an annual visual acuity test in accordance with ASNT SNT-TC-1A (2011) Note: This test includes a Jeager Eye Exam. Date of Visual Exam: 1/19/2024 Date of Next Exam: 1/19/2025 API 653 Annex G MFL Operations Certificate of Qualification This is to certify that: Aiken Arriola has successfully completed: MFL Floor Scanner Operator & UT Defect Sizing Date of Completion: 1/19/2024 Date of Refresher: 1/19/2029 This training certifies that the above-named personnel has met and PASSED the requirements of Powers Engineering & Inspection's (PEI) " PEI MAGNETIC FLUX LEAKAGE STANDARD OPERATING PROCEEDURES REV 6 2018” & API 653 Annex G “Qualification of Tank Bottom Examination Procedures and Personnel”. PEI Scanner Operator and Sizing Qualification, Testing and Training facilitated by third-party representative and PEI corporate procedures. To qualify, the following criteria were met: A written examination with a passing score of 75% or higher for scanning equipment and methods used. A minimum of 40 hours of training which includes: Instruction on the NDE principles/methods used by the bottom scanner, limitations and application of the specific scanning equipment and procedure, scanning equipment calibration and operation, and key scanning equipment operating variables; Hands-on operation of the bottom scanner under the direct supervision of a qualified scanning examiner. Performed practical examination for an MFL Floor Scanner/operator qualification and UT Defect sizing using the equipment below: o MFE Mark IV, III or II Modified 2412 MFL Floor Scanner and/or 1212 MFL Edge Floor Scanner o Panametrics 36, 37, or 38DL Plus, Panametrics right angle transducer, A-Scan UT, Panametrics Epoch III Flaw Detector, USM GO Flaw Detector. (CZ and Tight Area Inspection) Essential Variables for Qualification Test o Scanner & Prove-up Equipment as listed above o Qualification Testing performed on new and used test plates greater than 70 ft2. The test plates were 3/16-in, 6 mm, 1/4-in, 3/8-in, and 1/2-in thick. MFL Testing was performed through both thin and thick coated and uncoated plates. UT prove up thru uncoated and thin film. o Scanning and Prove-up Procedures Detection top and underside side pits of 90 to 100% Remaining Bottom Thickness (t) < 0.050-in (minimum 2 pits underside); 70 to 90% 0.050-in < t < 1/2 Nominal Thickness (T) (min 5 pits underside, 2 pits topside); 40 to 60% 1/2T < t < 2/3T (min 4 pits underside, 2 pits topside); and 100% of areas of General Corrosion Indication of Flaw Depth of +/-0.020-in for non-coated plates; +/-0.030-in for thin coated plates (0.001-in to 0.030-in) o Distance from shell < 1-in o Critical equipment setting per Manufacturer recommendations o Threshold Settings (Th) < 10% Th o Calibration performed all equipment used per Manufacturer recommendations. Authorized Inspection Agency Representative: Independent Third-Party Facilitator of Qualification Test Gary W. Powers, P.E. Owner / President / Inspector API 653 Authorized Inspector 0691 API 570 Authorized Inspector 22744 API 510 Authorized Inspector 24231 ASNT Corporate Level III UT, PT, MT and VT California Civil PE 60589 Tessa Campbell Training and Safety Professional OSHA 29 1910 HAZWOPER Sparks, NV 89431