COMPLIANCE INFO_2015 - 2018 - Laserfiche WebLink

Home Browse Search

kovihiEntry Bait Manual Flla*WOQ RKS BY DPW FUELING CONTAINMENT SYSTEMS 3.0 INSTALLATION INSTRUCTIONS For proper and warranted installation of flexible entry boots, these instruc- tions must be followed. Prior to installing the rubber entry boots, make sure the exact location has been prop- erly calculated. Sump access boots may be used to permanently seal any miscalculations. 3.1 Bolt Holes Locate the center entry point in the flat wall section of the sump base and drill a 5/16" hole. Install the entry boot template to the sump base wall using a 1/4" bolt and nut. Drill out the appropriate bolt hole circle for the size boot to be installed using the same 5/16" drill bit. After drilling, remove the template from the sump base wall. For proper installation, the appropriate size fabrication template should be used for accurate hole drilling. 3.2 Boot Openings After the bolt hole circle has been drilled, drill the entry boot opening by using the appropriate size hole saw. After the opening is drilled, dean any rough edges with a debuning tool or razor knife. WARNING: The appropriate hole saw size must alvmys be used for proper installation of the flexible entry boot Failure to use the required hole saw could dam- age the rubber boot after installation or prevent the boot from sealing properly and void product warranty. Hole Saw Flexible Entry Boots 2-3/8" EBF -0751, DEB -0751 4-1/4" EBF -0150, EBF -0200, EBF -0200X, DEB -0150, DEB -0200 5-1/2" EBF -0400, EBF -0300, All FlexWorks Entry Boots, DEB -0400, DEB -0300, All FlexWorks Double Entry Boots, except the DEB -4020 and DEB -4015. Saber Saw EBF -0600 3.3 Installing Rubber Boot Install the rubber boot from outside the sump by inserting the studs through the bolt holes. From the inside of the sump, install the compression ring over the studs and install nuts by hand. When installing double entry boots, install the inner portion of the boot and compression ring over the studs, and install the nuts by hand. Note: When using the DEB -0150 and DEB -0200 double entry boot with FlexWorks piping, you must insert the pipe through the entry boot prior to coupling the pipe. The nut of the SPC -0150 or the SPC -0200 will not fit through the outer portion of the boot A remote coupling machine may also be used in this application if the boots were previously installed. 3.4 Boot Fastening Using a 7/16" nut driver, tighten all of the nuts evenly in a clockwise sequence until 60 inch/lbs is attained on all nuts. This may require two to three revolutions to achieve. To prevent deformation of the boot, do not overtighten nuts. 3.5 Clamp Fastening Insert the appropriate sized pipe or conduit into the flexible boot from outside of the sump. After the pipe or conduit have been positioned, install the band damp around the boot and tighten to 30 inctObs. WARNING: Do not over tighten the band clamp beyond the maximum torque of 30 inch pounds or it is possible to damage the rubber boot 4.0 SUMP ACCESS BOOTS An optional "plug" style boot is available. This boot was designed to seal holes that are purposely drilled in the side of a dispenser sump for easier access to the sump's plumbing, or to seal any mistakenly drilled holes. See section 3.2 for proper hole saw size (Part# SAB -0400). 5.0 FLEXIBLE ENTRY BOOT INSTALLER TOOLS In order for proper installation of the flexible entry bootto occur, the correct size bolt holes and boot openings must be drilled. The fol- lowing installer tools are available: 5.1 Entry Boot Templates These pre -drilled metal templates have all of the bolt hole patterns for each size of the flexible entry boots. Refer to Section 3.1 is.manua_ l,-fbr wage„ -- the entrymplate. MAR 31 2016 ENViRuIiIAEVAL HE41Tu rV=VAPT% r"