Laserfiche WebLink
oeicmAL <br />Easy Installation! The 3" inlet or the 99 LD -3000 allows the leak detector to -e installed in the discharge port of <br />3 - 5 HP submersible pumps. The discharge of the 99 LD -3000 is 3" male thread; Height - 16.25 inches. Width - 7.86 <br />inches. Weight - 29 pounds; Can be installed by one person. Now with easy access to check valve for field replacement. <br />The 99 LD -3000 is available with flange fittings instead of threads as Part # 99 LD-3000\FL. <br />Integrated In -Line Check Valve/ Pressure Relief: Allows the leak detector to compensate for a defective <br />submersible pump pressure relief or check valves that allow drain -back into tanks. The integrated pressure relief valve <br />of the 99 LD -3000 will hold 30 PSI in the line by itself. <br />One Way Poppet Flow Path! Isolates pump turbulence from line leak detection at pump start-up. The hardened <br />stainless steel poppet does not dimensionally change due to thermal conditions encountered during station operation <br />(precision metering change is insignificant down to -20 degrees F). <br />Reverse Ratio Piston / Poppet Combination: The leak detector has a smaller diameter piston area than <br />the poppet it is attached to. This allows the leak detector to stay in the fast fill position (3 GPM) to a higher pressure <br />while compressing vapor pockets and stretching flexible line faster, resulting in less time to full flow. <br />Smaller Volume / Faster Response Piston Size: Results in one-fourth the volume of fuel to replace <br />when in leak search and one-fourth the volume to return to the line when pump is turned off. This results in achieving <br />faster full flow to dispensers and faster resets to detect leaks. <br />Technical Specifications 99 LD -3000 <br />Fuels: Gasoline, 100% methanol*, 100% ethanol*, up to 15% MTBE I 7.86 <br />• Any combination of the above <br />#1 or #2 diesel, kerosene, Jet A* or JP -4*, AV Gas* 5.56 --I <br />and Biodiesel* (all blends). <br />* When used with Biodiesel, any alcohol fuel concentration above 20%.Jet A, JP -4, or <br />AV Gas, order part # LD3-SSVS for stainless steel fittings and stainless steel vent <br />tubing. For chemical applications other than those listed above, contact factory. <br />Certified to meet EPA 3 GPH @ 10 PSI: <br />• Rigid pipe up to 406 gal., 1171 ft. of 3" id. <br />1625 <br />• Flexible pipe up to 96 gal., 260 ft. of 3" id. <br />Combination of Rigid and Flexible pipe up to 502 gal., 1431 ft. of 3" id. <br />PORT <br />A <br />Construction: Forged steel body; Steel alloy; Forged steel threads. <br />(PUAP PRESSURE) <br />Cylinder Assembly: Anodized 6061-T6 Aluminum <br />Internal Parts: Anodized 2011-T3 Aluminum, 6061-T6 Aluminum; <br />Acetron GP; CDSM 1026 and DOM 1026 steel; 5.75 <br />TEST <br />17-4 stainless steel <br />3' MALE NPT- <br />PORT <br />B <br />Seals: Low drag, stainless steel spring energized teflon seals 0 <br />WK PRESSURE) <br />O Rings: U.L. Approved V9702-Viton Type B Fluorocarbon 1/0 NPT <br />TYPICAL <br />Metering Pin and Poppet: 17-4 stainless steel <br />Check Valve: Acetron GP, Viton F Seal 3' MALE NPT <br />Pressure Relief: Stainless Steel, 29 PSI pressure relief. This pressure is in <br />addition to the pump pressure relief. <br />Inlet: 3" male outlet: 3" male <br />• Certified to handle 12+ feet of head pressure. <br />• Exceeds EPA specifications for 3 GPH @ 10 PSI hourly test. <br />• Vent line must be unobstructed, leak tight and connected to headspace of tank, not to be subjected <br />to pressure or vacuum. <br />• Combination line check/pressure relief prevents drainage into the tank. <br />AN Vaporless Manufacturing, Inc. Toll Free: 1-800-367-0185 <br />8700 East Long Mesa Drive Phone: (928) 775-5191 <br />you Prescott Valley, Arizona 86314 Fax: (928) 775-5309 <br />02/08 Web Site: www.vaporless.com • Email: vmi@vaporiess.com <br />