INSTALL_2013 - Laserfiche WebLink

Home Browse Search

ITEM#101 FixedFEMI Submersible Turbine Pumps 1/3 and 3/4 HP Fixed Speed Submersible Turbine Speed Submersible Pump Specifications Turbine • - Liquid Compatibility Designation System •Max.liquid viscosity:70 SSU at 60"F(15"C). A typical turbine model designation •Standard models are UL and cUL listed for " has up to five components to define fuel mixtures containing up to 15%ethanol the pump being supplied as follows: or methanol,and 20%MTBE,20%ETBE or STP XXXXX Y - A - B 17%TAME with gasoline. •STPAG models are compatible with fuel _STP= Basic Model Designation B mixtures containing up to 100%ethanol or methanol,and 20%MTBE,20%ETBE or X= Factory 17%TAME with gasoline. Installed Options • 1/3 and 3/4 hp fixed speed models can STP model designations may include also be used with diesel fuels,fuel oils, one or more of the following kerosene,Avgas and jet fuels in a non-gelled characters in alphabetical order: A pourable state. AG=Alcohol-gasoline compatible •All wetted elastomers are made of a high (100%ethanol or methanol capable) grade,fluorocarbon Viton® compound. Note:Standard models 0%to 15% ethanol or methanol capable. Standard Features F=Floating suction adapter • 1/3 and 3/4 hp fixed speed models are (I-1/2"NPT female adapter) available in variable and fixed Y K=Intake filter screen length options. (IFS,factory installed to PMA) •Check valve:2-3/4"diameter fluorocarbon •R=Model R check valve Vitons"seal constructed on cast aluminum (24 psi relief/22 psi reset for PLLD) body and steel backing washer. •W=Model W check valve For full diagram see page S. •Pressure relief valve:available in four (16 psi relief/13 psi reset for PPM4000) pressure relief settings,integral to check 'Note:If not otherwise specified,all _ Power Requirements valve.Standard model relieves at 40 psi and STP models supplied with • 1/3 and 3/4 hp fixed speed models resets above 35 psi. standard model check valve require single-phase,208-230 VAC, •Syphon:venturi-type syphon primer - (40 psi relief/35 psi reset for 60 Hz incoming power. supplied with every submersible.Syphon =� MLD and TS-LS300) rY YP• 1/3 and 3/4 hp fixed speed models check valve and seconds s hon sold � = Pump MotoR '�• incorporate a starting and running separately. Horsepower Rating capacitor,with internal bleed resistor, •Air eliminator:every submersible includes a 33= 113 hp fixed speed rated 370 Volt, 15 microfarad. tank return path with one-way check valve •STP-SCI single-phase smart controllers and to provide active air elimination. 75=3/4 hp fixed speed STP-CBS single-phase control boxes are • Electrical disconnect:electrical yoke /q= Model Length" available for 1/3 and 3/4 hp pump control. for positive contractor disconnect VLI =Variable length range#I. • 1/3 hp max.motor draw:4 Amps. during service. VL2=Variable length range#2. • 3/4 hp max.motor draw:7 Amps. Approvals VU =Variable length range#3. Note:VL2 models fit 94%of all Pump Motor •Consult factory for Iii own installations. applicable approvals. • I/3 and 3/4 hp fixed speed,3450 rpm, er Pipe Length two-stage centrifugal type pump motor Quality Certification with integral,automatic,thermal e length is expressed as two overload protection. • Franklin Fueling Systems is an ISO 9001 haracters that indicate the • 1/3 hp models have a max.flow of Certified Manufacturer. th of the riser in inches.Riser 40 gpm and a max.pressure of 28 psi. •Viton®is a registered trademark of DuPont available from 7"to 69"in •3/4 hp models have a max.flow of Dow Elastomers. ents(additional charge for 65 gpm and a max.pressure of 31 psi. or longer). C UL US LISTED 9