Laserfiche WebLink
CAUL ION---The enclosure cover must be removed STARTER WITHOUT CONTROL TRANSFORMER <br /> to install this kit. During installation <br /> Provide protection for 111e machined <br /> Ilanl;es of lite cover and case to pie- <br /> vent rucks and scratches. <br /> RED LEAD10 11MRAL <br /> _ <br /> I <br /> �4 <br /> YELLOW irAD L4 <br /> 10 <br /> '• I' <br /> MU511ION 1•01110N 1'OSIII0N <br /> � 1 L ft` <br /> If <br /> BLACK L[wP <br /> rO uIMINAL �.i IAONNIINC <br /> '4 R .Il it ;�: { •-� <br /> I <br /> PL tics SPRING It it <br /> CLIP OPLRAION <br /> RCIAINfN <br /> PUstfOUT10N <br /> FIGURE 2 0n11 <br /> FIGURE 4 <br />' PUSIINDITUN 1--Assemble the pushbutton unit to the overload relay with the mounting <br /> OPENAIOEi screws. <br /> 2—Connect the pushbutton unit wires to the starter terminals as follows: <br /> ENCLOSURE Red Lead—Connect to Terminal #1. <br /> COVLR Yellow Lead-- Connect lu Terminal 4=?-. <br />' Black Lead—Connect to Terminal 413. <br /> 3----The starter is now wired per Figures 1 and "A" as shown on the <br /> diagram in the starter cover. <br /> 1 GROOVE FOR <br /> SPRING CLIP RLIAMEN STARTER WITH CONTROL TRANSFORMER <br /> YELLOW LEAD <br /> 101ENNINAL ,I 1. '•� <br />' ND 2 4. w• _ <br /> SPRING � <br /> [LIP WAINEN <br /> FIGURE 3 ,[ <br /> SEE FIGURES 1, 2 AND 3 i n' <br /> 1 <br /> 1 c <br /> -•---Remove the enclosure cover and place it on a <br /> protected surface in a position which provides <br /> access to the inside of lire cover. . { <br />' 2---Remove the plugs tronl positions 1 and 3 by— <br /> a—Renluve lite spring clip retainers. <br /> b—Rer love lite plugs with a screwdriver by 1 <br /> rotatkig clockwise. <br />' 3--Froin the outside of the cover install the black fq <br /> pushbutton operator in Position 1 and the Fed 1 <br /> I]n511JliltOrl Operator in POSIl1Or1 3 by threading BLACK LEADscxErs\�yJ-� MOunndc RED LEAD <br /> into the holes until they are finger light. PD Tlan <br /> 1011R41NAL Uhl] 10 lEitYINAL <br /> 4--Use the new spring clip retainers supplied with No.1 NU.t <br />' <br /> this kit and assemble them to engage the <br /> groove provided in each operator. FIGURE 5 <br /> IMPORTANT—The retainer is a safety feature in- 1—Assemble the pushbutton unit to the overload relay with the mounting <br /> tended to prevent disengagement of the operator screws. <br /> hole the cover. Special care stluuld be taken to 2-....Connect the pushbutton unit wires to the starter terminals as follows; <br /> Insure they are properly installed in the retainer Red Lead—Connect to Terminal #1. <br /> groove (see Fig. 3). Yellow Lead—Connect to Terminal 41:2. <br /> 5—Fasten the Legen.l Plate to the front of the Biack Lead—Connect to Terminal #3. <br />' cover using ole thread cutting screws pro- 3—The starter is now wired per Figures 1 and "A" as shown on the <br /> vided. diagram in the starter cover. <br /> 1 <br /> f <br />