INSTALL_1989 - Laserfiche WebLink

Home Browse Search

,Extra . ,9-33 Series ,- e OPW 233 Series Extractor fittingsbE allow foot valves and ball float vent" mn valves to be removed from under 's_ ver _ ground tanks without breaking upthe concrete. for OPW extractor wre y n See selection. ag IV( in ` 'imensions OPW 233-E 1, •S�. enc A Top thread 4" op W � Outlet thread 1'/2" The OPW 233-E Extractor fitting is for as nter al Bads t©actractor cept a connecting Inlet male thread 4" use with any 1'/2" foot valve with a r maximum outside diameter of 23/4". nipple between the extractor andthe MaximumlcleaeiaD. 1'h" The 233-Ehas 4 male thread for con tank flange, which provides an optionthroughvalve 2A* _' vection to 4"tank flange and is gas- to adjust the elevation of the 233 P in a ket-sealed to prevent loss of prime, relation to the tank. The cage of the VM OPW233-P 2"Sixs a caused by air being sucked In through 233-P is easily replace� because ut like is � the top fitting, threadless-it is simply To thread 4" ' vidf bottle cork. p Materials Outletthread 2" M Body: cadmium plated cast iron Materials Inletthread 4" e` tar Cap and suction stub adaptor:bronze Body: cast iron Ca e fl thread 2" tar VSS Gasket: chromed tanned leather Seals: buage: ona-N O-ring Maximum clear I.D. tc SIZE: 11/2" WT.: 20.22 lbs. SIZE: 2" WT.: 18.00 lbs. through valve 31/2" mai 233-E-4040 233-P-6050 YTS Par 1,'f 233-VMP a _ OPW P� f� FC The OPW 233-V Series Extractors are used to hold and VP OPW Test Plugs are used to isolate . position the OPW 53-V Series Float Vent Valves in the underground storage tank. It is furnished complete with tank from the vent piping system du an extractable cage.The entire Float Vent sub-assembly tank testing. ` {/i can be extracted from the tank by using either an OPW The 233-VP plug is used on: ° N 52 or 89 Extractor Wrench, for tank testing. 233-V-4420 (4" x 2� The OPW 233-V extractor is a single outlet extractor used 233-VM-4422 (4•x 20 X is O in non-manifolded vapor recovery systems, or systems The 233-VMP plug is used on: flog such as shown on p. 7. 233-V-4420 (4"x 2')"- pro: Materials: 233-VM-4422 (4•x2'X Body: cast iron w/Duragard" coating 233-VM-6045 (4"x 2•X - Extractor: bronze he 233-VP-6046 WY.: •7g int V SIZE: 4" x 2" WT.: 15.33 lbs. 233-V 4420 233 VMP-6047 WT.: 1.24 nth OPW Vit, :fnsions gall 233V 233VM 2I unc n: The OPW 233-VM extractor is amulti-outlet extractor, enc available in 2 sizes; used in direct manifolded systems. , 4420 4422 804 oun vapor recovery, or where provision for Stage II Vapor (Tee) (Cross) the Recovery is needed. Top Thread 4" 4" 4 tan SIZES:4" x 2" x 3" WT. 18.73 lbs. 233-VM-6045 Outlet Thread 2" 2" A erg 4" x 2" x 2" WT. 16.62 lbs. 233-VM-4422 — 2„ ,, ver All OPW 233-V series extractors are specially coated with Tank.Connec- black Duragard'" coating, for improved corrosion tion Thread 4" 4" 4 i resistance and easier cage removal. J■µ/ms, � -.