Laserfiche WebLink
40 to Preparation and Installation Inactions <br /> EMC Basic Monitoring Console Oil <br /> TO THE INSTALLER! WARNING:RE SURE POWER TO THE MOM- <br /> Tvo O CONSOLE CIRCUIT iSTURNED OFF <br /> READ AND UNDERSTAND BEFORE CONNECTING POWER WIRING. <br /> THIS INFORMATION DEATH, <br /> TO DO SO COULD RESULT IN <br /> DEATH, SERIOUS PERSONAL INJURY, <br /> PROPERTY LOSS AND EQUIPMENT RAM- <br /> C. CONNECTOR POSITIONS AGE. <br /> AND LABELING. <br /> Power Supply Rating: <br /> The position of the Monitoring Console Input power:(L', G,N); 115 VAC, 60 Hz. <br /> connectors and the devices wired to the <br /> connectors must be recorded to prevent Output Power:Alarm Relay Contacts, resistive load— <br /> improper replacement during installa- 120 VAC, 2A Max.; or, 24 VDC, 2A Max. <br /> tion or service. A circuit directory is ad- AIL, <br /> tiered to the back of the right-hand door for R.ItIKI: G„S1v„P UG <br /> ,p.w[ <br /> ta.1111, ( Ct OSE iI TO <br /> this purpose. (See Figure 10.) 7.170■.,.E CONDUIT ENT RY <br /> M <br /> Y11 YOt <br /> During programming,connector positions and <br /> the devices wired to the interface are identi- <br /> fied and stored in memory. If probe wiring is <br /> removed from its connector terminals ormoved <br /> �r <br /> to .different terminals, the system will not �H=a <br /> CONNECTOR <br /> properly recognize the data being received. LL <br /> „D • <br /> 1. Connector Position. Ga <br /> a. Identify all connectors according to << <br /> their slot location. <br /> b. Once a probe has been wired to certain <br /> terminals on a connector and the system has RIGID z'.� MONITOR <br /> been programmed,the wires from that probe <br /> may not be relocated to other terminals with- <br /> out reprogramming the system. Figure 9. Power Wiring Diagram. <br /> 2. Circuit Directory. A circuit directory (see 1. Connect a#t 12 AWG(or larger)barrier ground conduc- <br /> Figure 8, "Circuit Directory—Example") ap- for from the ground lug closest to the conduit entry in <br /> pears inside the front-panel door.It should be the monitor to the earth ground bus on the power panel <br /> filled out by the installer as the module con- being used to supply AC line voltage to the Monitoring <br /> Console(see Figure 9,"Power Wiring Diagram"). <br /> nectors are being wired. <br /> I NOTE:If connecting to a subpanel,be sure there is <br /> For each connector, record the physical loca- �, an earth ground connection between the subpanel <br /> tion or type of device wired to each position on and the main power panel in accordance with the <br /> the connector. National Electrical Code. <br /> In the example shown in Figure 8,Probe Con- 2. Connect the puwer and ground wires(L',G,and N)to the <br /> nectorLocation 1 shows a magetostrictive probe proper terminals in the AC connector(see Figure 9). <br /> is installed in Tank 1(receiving+and-wires). g. Connect the power supply wires in the power panel to <br /> a separate dedicated circuit. <br /> D.POWER WIRING CONNECTIONS. 4. Check to be sure that the electrical resistance between <br /> the monitor ground terminal and a known good earth <br /> WARNING: IN INSTALLATION OF THIS ground is less than lil. <br /> PRODUCT, COMPLY WITH THE NATIONAL E. PROBE WIRING CONNECTIONS. <br /> ELECTRICAL CODE;FEDERAL,STATE,AND <br /> LOCAL CODES; AND ANY OTHER A.PPLI- A. WARNING: IN INSTALLATION OF THIS <br /> CABLE SAFETY CODES.INADDITION,TAKE 'Itif PRODUCT, COMPLY WITH THE NATIONAL <br /> NECESSARY PRECAUTIONS DURING IN '{{i�f E�CRICAL CODE; FEDERAL, STATE, AND <br /> STALLATION, SERVICE AND REPAIR TO LOCAL CODES; AND ANY OTHER APPLI- <br /> PREVENT PERSONAL INJURY, PROPERTY CABLE SAFETY CODES.IN ADDITION,TAKE <br /> LOSS AND EQUIPMENT DAMAGE. <br /> II <br />