INSTALL_2003 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed RED THREAD' IIA Piping GENERAL SPECIFICATIONS PrimarPi in Secondary Containment Piping SCOPE SCOPE PIPE - Pipe shall be manufactured by Smith Fibercast by PIPE- Pipe shall be manufactured by Smith Fibercast by using a thermosetting epoxy a filament winding process using a thermosetting epoxy a filamen[winding process g resin to impregnate strands of continuous glass filaments resin to impregnate strands of continuous glass filaments which are wound around a mandrel at a prescribed helix awhich are ngle and under dcaround n rollled tension. at a prescribed helix angle and under controlled tension. All pipe will be supplied with matching tapered T..A.B."' (Threaded and Bonded) coupling and spigot ends or T.A.B. spigot x CONSTRUCTION spigot ends. 3"-4"PIPE- RED THREAD IIA pipe shall have continuous glass fibers filament wound at a 35%' helix angle in a CONSTRUCTION matrix of epoxy resin. Pipe shall be in compliance with 2"-4"PIPE-RED THREAD IIA pipe shall have continuous ASTa 11 M and performance itscmentsaand metion chanice. al glass fibers filament wound at a 355^ helix angle in a I ro encs anll d shall be ce require with the following matrix of epoxy resin. Pipe shall be in compliance with designation codes: AST\l D2310 and classified by its designation code. Pipe i g Desi nation Code at 73.4' F shall meet all dimensional and performance Size 9 requirements, mechanical3- RTRP-1 l AE properties. and shall be RTRP-11 AF classified with the following designation codes: % 4' Size Designation Code at 73.4'F i 2--3• RTRP-11 AE ITEMS 4" RTRP-11AF i 3"-4"PIPE- Glass fiber reinforced filament wound pipe with Plain end by Plain end. Pipe to be factory ITEMS prooftested at the following pressures: 2"-4"PIPE -Glass fiber reinforced filament wound pipe Y.300 psig(minimum) with matching tapered T.A.B. (Threaded and Bonded) 4--265 psig (minimum) coupling and spigot ends. Pioe to be factory prooftested I 3"4"FITTINGS - Compression molded two-piece fittings at the following pressures: i shall be manufactured using a vinyl ester molding 2--375 psig compound. The molding compound shall be reinforced 3--300 psig I with a minimum of 6096 chopped glass fiber. 4'-265 psig I ADHESIVES- Adhesive and curing agents shall be either 2"-4"FITTINGS-Compression molded fittings shall T ' UL Listed DS-8000 or DS-7000 series adhesive. Consult manufactured using an epoxy molding compound. The i Smith Fibercast's installation manual No. 82160 for molding compound shall be reinforced with a minimum recommended heat curing techniques. of 45%chopped glass fiber. In-line fittings are filament I JOINING TECHNIQUES wound. ADHESIVES-Adhesive and curing agents shall be either I 3"-4"PIPE and FITTINGS- Pipe shall be joined with UL Listed DS-8000 or DS-7000 series adhesive. either DS-8000 or DS-7000 series adhesive. Fittings shall Consult Smith Fibercast s installation manual No. B2160 be adhesives and td with vrher DS-7000 r Drial to 80001series in for recommended heat curing techniques. accordance with Smith Fibercast s installation manual JOINING TECHNIQUES No. B2,"0. 2"-4"PIPE and FITTINGS-Pipe and fittings shall be TESTING joined with DS-8000 or DS-7000 series adhesive using 3"-4" SECONDARY CONTAINMENT PIPE SYSTEMS- matching tapered bell/coupling and spigot. Material to Secondary containment pipe systems should be tested be installed in accordance with Smith Fibercasts prior to use to assure soundness of all joints and installation manual No. B2160. connections. Consult Smith Fibercas['s installation TESTING manual No. B2160. 2"-4" PRIMARY PIPE SYSTEMS - Primary pipe systems should be tested prior to use to assure soundness of all joints and connections. Consult Smith Fibercast s installation manual No. B2160. 5