Laserfiche WebLink
i` - W «wrrrr`.rrar <br /> C. Termination fittings <br /> Termination at the bulk tank connections is aocom- D. Bonding and Assembly <br /> plrshedbyusinga termination concentric reducerwith - - (For Containment Piping) <br /> V," female NPT threaded outlet. (See Figure 5) Use only DS-7014. DS-7024 or DS-7069 adhesive <br /> _ manufactured by A.O. Smith-Inland for installation of <br /> Fiber Wass - A.O. Smith-Inland containment piping systems. The <br /> Threaded gdapror- - number of 3"' containment fittings which can be <br /> feel] a Matai - bonded from ono DS:7014, DS-7024, or DS-7065 <br /> adhesive kit is shown in Table It. <br /> s <br /> —_� TABLE It <br /> Bonding of Containment Fittings <br /> DS-7014 4 DS 7024 Kil, <br /> t7 Type of Fitting Fillings Per Kit t DS-7069 P Kit <br /> p - ..._. Fittings Per Kit <br /> t o ah" NPT 3" 90` Elbow 11,'�• r I 3" 45' Elbow 2r <br /> 2 <br /> 3" Tee 3 <br /> ( O2 <br /> O O 3" CouPting -' 3 <br /> 3" x T' Ternunahon <br /> Tank <br /> rwvns Concmitnc Rnducur 1. 3 <br /> NOTE: eat present <br /> tm e. and 6' diameter fittings not <br /> available at present erne: <br /> Termination at the dispenser is at the and of the fiber <br /> glass containment piping and is accompbshed using a Refer to bonding proce.tures.in Manual 1055 for <br /> termination concentric reducer. (See Figure 6) adhesive mixing and surface cleaning. <br /> D.penser "F, <br /> After cleaning all sanded surfaces, apply a thick <br /> coaling (1/16" minimum) of adhesive to the socket <br /> ® fbeli) area of the fining. The stir stick supplied with <br /> i. es the adhesive kit works well as an applicator. Libera'iy <br /> apter coat The tabs(Oat bonding surfaces) of both halves of <br /> a le( thefittingswith adhesive(1/16"minimum thickness). <br /> Apply a thick coating(1/16" minimum)of adhesive to <br /> o the $ended surfaces of the pipe ends <br /> NOTE: Two-piece containment fittings require <br /> more adhesive than is normally used with A,O. <br /> OSmith-inland bell and spigot joints. <br /> Use the bolts, nuts and washers to assemble the <br /> .reteel fittings on the pipe. Two 7/16"Wrenches are required <br /> Fipure a for the bolts. Note tfiat a flat washer is required on both <br /> halves of the fittings. (Sea Figure 4) Tighten the nuts <br /> Termination on the shear valve(impact valve) may be and bolts completely. <br /> accomplished with a flexible hose. clamped and Make sure that adhesive fills an <br /> + bonded in piece. (NOTE, Not supplied by A0, Smith. ends and fitting sockets (bells), Bopbetween pipe <br /> Inland) (See Figure 7) <br /> Diapense. Care should be taken not to disturb the containment <br /> �- Impact valve Piping joint when assembling additional joints. The <br /> adhesive must be fully cured before applying stress to <br /> assembled joint. Use.adhesive as thread sealant for <br /> NPT threads on termination fittings. <br /> Rubber it", <br /> Fiayra 7 Galvetased Steel <br /> j ' <br /> 3 <br /> i <br />