|
PERFORMANCE SPECIFICATION - CONTINUED
<br /> SECTION VII ELECTRICAL WORK .- CONTINUED SECTION VII ELECTRICAL WORK - CONTINUED SECTION IX CANOPIES - CONTINUED
<br /> PART 2 - PRODUCTS PART 3 - EXECUTION -- CONTINUED PART 1 - GENERAL - CONTINUED 0 -
<br /> 2.1
<br /> ,2.1 IDENTIFICATION OF EQUIPMENT AND WIRING: PROVIDE IDENTIFICATION 'NITH 3.8 OPERATING AND ACCEPTANCE TESTS: 1 .1.1 COMPLETE FABRICATION DRAWINGS INCLUDING FOOTINGS DESIGN. V R air
<br /> DYMO TAPE OR EQUAL FOR ALL SERVICE ENTRANCE AND DISTRIBUTION 3.8.1 CONDUCT OPERATING TEST ON ENTIRE ELECTRICAL INSTALLATION; ALL SYSTEMS 1 .1.2 COMPLETE ABOVE GROUND STRUCTURAL SUPPORT SYSTEM.
<br /> EQUIPMENT INCLUDING MAIN SWITCHGEAR, PANELS, DISCONNECT SWITCHES, MUST BE COMPLETE AND IN GOOD OPERATING ORDER. REFER TO START-UP AND FINAL- 1.1.3 STEEL ROOF DECK, SMOOTH WHITE 90% REFLECTIVE PAINT. b�d
<br /> CONDUITS, ETC., AND FOR MOTOR FEEDERS INCLUDING SWITCHES. STARTERS CHECK-OUT OF SYSTEM COVERED ELSEWHERE. y�
<br /> 1 .1.4 ROOF BRACING. g d
<br /> AND MOTORS. 00 NOT START OR OPERATE EQUIPMENT WITHOUT SPECIFIC DIRECTIVES OF OWNER'S �' e
<br /> SPECIFIED REPRESENTATIVE. ANY DAMAGE TO OWNER'S EQUIPMENT DUE TO 1.1.5 CAP FLASHING. 0 .n
<br /> 2.2 LIGHT FIXTURES: TO BE PROVIDED BY OWNER. C)
<br /> DEFECTIVE INSTALLATION AND/OR OPERATION WILL BE THE RESPONSIBLI7Y OF THAT 1. 1.6 DOWNSPOUTS - INTERNAL INSIDE COLUMNS. (11) �
<br /> 2.3 CONDUITS: PROVIDE THE FOLLOWING TYPES OF RACEWAYS IN ACCORDANCE SUBCONTRACTOR FOR CORRECTION, REPLACEMENT AND/OR MONETARY COMPENSATION
<br /> WITH THE SPECIFIC APPLICATION OF I_OCAFION INDICATED. 1.1,1 PERMITS AND INSPECTIONS.
<br /> A. '
<br /> '1,.3.1 RIGID GALVANIZED STEEL: WHERE EXPOSED TO THE WEATHER; FOR AS REQUIRED1 .1 .8 INSTALLATION AND FRAMING FOR OWNER-SUPPLIED FASCIA SIGNS INCLUDING ELECTRIC.
<br /> ENCLOSING MAIN GROUNDING CONDUCTOR: 'WHERE REQUIRED FOR 3.8.2 MAKE INSULATION TESTS ON MAIN SERVICE EQUIPMENT AND ALL FEEDERS AND 1 .1,9 INSTALLATION AND FRAMING FOR FASCIA MATERIAL AS PER OWNER SPECIFICATIONS,
<br /> MECHANICAL. PROTECTION OR WHERE SPECIFICALLY INDICATED. MATERIAL PANELSOARDS, -
<br /> SHALL BE AS MANUFACTURED BY GENERAL ELECTRIC, REPUBLIC 3.8.3 TESL' GROUND: RESISTANCE TO GROUND SHALL NOT EXCEED 25 OHMS, PART 2 - PRODUCTS
<br /> YOUNGSTOWN STEEL AND TUBE, OR EQUAL. PROTECT WITH ASPHALTIC 3.8.4 INSPECT ALL PANELBOARDS. ALL CONNECTIONS MUST BE TIGHT AND SECURE. 2. 1 ROOF STEEL DECK ROOF STEEL DECK SHALL BE 2 1/4 " MINIMUM DEEP, 24 GAUGE
<br /> PROTECTIVE COATING WHEN BELOW FINISH GRADE. 3.9 "AS-BUILT" DRAWINGS: FURNISH OWNER'S CONSTRUCTION MANAGER WITH ONE SET BAKED WHITE ENAMEL STEEL WITH MINIMUM SECfW MODULES OF 0.25 IN 1/4 .3 MOMENTle
<br /> �-
<br /> OF INERTIA OF 0.030 IN 14/4 4. ----
<br /> 2.3.2 SEALOFFS: WHERE CONDUITS EXIT FLOOR OR CONCRETE AT DISPENSERS, OF MARKED-UP PRINTS SHOWING "AS-BUILT" INSTALLATION.
<br /> 2.2 STRUCTURAL STEEL:
<br /> TANK GAUGING, SUHMERSIBLE PUMPS AND WHERE CONDUITS TRANSVERSE 3. 10 FINAL ACCEPTANACE: UPON COMPLETION OF WORK, PRESENT CERTIFICATE OF APPROVAL
<br /> OF LOCATION OR COVERNING INSPECTION AUTHORITY.
<br /> HAZARDOUS ZONE (LE. YARD LIGHTS, AIR/WATER UNIT, LIGHTED SIGNAGE) 2.2.1 ALL STRUCTURAL STEEL TO BE A.S.T.M. A-36 AND SHALL COMPLY WITH THE STANDARDSPECIFICATIONS FOR STRUCTURAL STEEL FOR BUILDINGS OF AI.S.C. AND WITH THE
<br /> SEE ELECTRICAL SITE PLAN FOR ZONE LIMITS. 3.11 CLEAN-UP: CLEAN UP ALL DEBRIS CAUSED BY WORK OF THIS SECTION, KEEPING
<br /> ALS.C. CODE OF STANDARD PRACTICE (LATEST EDITION).
<br /> 2.3..3 PVC CONDUITS: ALL. WIRING RUNS BURIED UNDERGROUND UNLESS THE PREMISES CLEAN AND NEAT AT ALL TIMES,
<br /> 2.2.2 MCH STRENGTH BOLTS SHALL CONFORM TO THE STANDARD SPECIFICAfIN A.S.T.M,
<br /> OTHERWISE INDICATED. MATERIAL SHALL. BE HEAVY WALL, TYPE II RIGID SECTION VIII PAINTING
<br /> SCHEDULE 40 AS MANUFACTURED BY CARLON, BALDWIN, TRIANGLE, OR EQUAL. A325", AND SHALL BE PROVIDED WITH CARBONIZED WASHERS UNDER THE NUTS.
<br /> 2.2.3 ALLLLOTHER BOLTS SHALL DF A-307 AND SHALL CONFORM i0 A.SJ.M. STANDARDS,
<br /> PVC CONDUITS SHALL HE U.L. LISTED AND APPROVED. PART 1 - GENERAL WITH WASHER REQUIRED.
<br /> 2.4 CONDUCTORS: V 1 t SCOPE: THIS SECTION COVERS THE FURNISHING OF ALL LABOR, MATERIALS, 2.2.4 ALL HIGH STRENGTH BOLTS SHALL BE TORQUED TO PROVIDE A MINIMUM TENSION IN
<br /> 2.4.1 FURNISH AND INSTALL COLOR COOED COPPER CONDUCTORS, 600 VOLT, OF -
<br /> SIZES INDICATED. MINIMUM SIZE .#12 (TEEN) EXCEPT FOR SIGNAL AND CONTROL SERVICES, EQUIPMENT AND APPLIANCES IN CONJUNCTION WITH OR PROPERLY INCIDENTAL BOLI OF 90% OF MINIMUM PROOF LOAD OF THE BOLI. vi
<br /> CIRCUITS AND WHERE OTHERWISE NOTED. TYPE TW (60 DEGREES CENTIGRADE) TO THE COMPLETION OF ALL PAINTING OF SURFACES COMPLETE, INCLUDING 2.2-5 TUBE COLUMNS SHALL COMPLY WITH A-53, GRADE B. p
<br /> PAINTING OF THE FOLLOWING SURFACES: R
<br /> FOR GENERAL BRANCH CIRCUIT 'WIRING; TYPE THN (90 DEGREES CENTIGRADE) 2.2.6 ALL TUBE COLUMNS SHALL BE 46 KSI STEEL. u
<br /> FOR SUPPLY CONNECTIONS TO LIGHT FIXTURES- INSTALL PER COLOR CODE OF 1 .1.1 MISCELLANEOUS METAL, DOWNSPOUTS, COLUMNS, POSTS, ISLAND FORMS, VENT
<br /> 2.2.7 ALL WELDING SHALL BE WITH E70XX ELECTRODES AND BE ACCOMPLISHED BY
<br /> NEC. LINES, MANHOLE COVERS AND ELECTRICAL CONDUITS. U
<br /> CERTIFIED WELDERS. w
<br /> CL
<br /> 2.4.2 SHIELDED CABLES: PROVIDE SHIELDED CABLE FOR INTERCOM AS PER 1 ,2 PAINTING DOES NOT INCLUDE: in
<br /> FASCIA:
<br /> MANUFACTURER'S SPECIFICATIONS AND AS REQUIRED ON DRAWINGS. 1.2.1 PAINTING CANOPY SOFFITS. --°- - ---
<br /> 2.5 SPLICES AND CONNECTIONS: PROVIDE SPLICES ONLY IN READILY ACCESSIBLE 1,2,2 PAINTING LIGHT FIXTURES. 2.3. i FASCIA BACKING PLYWOOD SHALL BE MINIMUM i/2 " THICK MARINE GRADE. MARINE q b
<br /> GRADES SHALL MEET THE REQUIREMENTS OF EXTERIOR TYPE AND SHALL BE ON OF
<br /> OUTLET BOXES. PROVIDE INSULATED PRESSURE CONNECTORS OR "CRIMP-ON" O
<br /> SLEEVES WITH OVERALL NYLON INSULATORS FOR CONDUCTORS. CONNECTORS t.2.3 PAINTING FASCIA SIGN FRAMES. GRADE 1 -1, NIGH DENSITY OVERLAY.
<br /> U �
<br /> SHALL OF 3M "SCOTCHLOK", BUCHANNA.N SPLICE CAPS WITH INSULATED WRAP, 1.2.4 PAINTING GASOLINE EQUIPMENT. 2.3.2 VERTICAL SUPPORTS SHALL BE 14 GA STEEL. STUDS AT 14" O.C. OR 3 X 3 X 1/4 < w ti YQ
<br /> WITH CORRESPONDING MEMBERS TOP AND BOTTOMC.
<br /> OR IDEAL "CRIMP-SLEEVES" WIWITHSCA.P CAP INSULATOR OR EQUAL. 1.3 COLOR SCHEDULE: COLOR OF PAINTS SHALL BE A5 LISTED IN COLOR SCHEDULE. STEEL ANGLES ALL AT 24" O, Q_
<br /> 2.6 PANELBOARDS: PART 2 - PRODUCTS SUPPORT. s
<br /> 2.6.1 BRANCH CIRCUIT PANELBOARDS: PROVIDE FLUSH-MOUNT CIRCUIT BREAKER TYPE2.1 PAINT MANUFACTURERS AND PRODUCTS: PAINTING SYSTEM AS SPECIFIED HEREIN IS
<br /> 2.3.3 SCREWS FOR FASCIA SHALL BE ALUMINUM OR GALVANIZED SIZE AS REQUIRED.
<br /> PANELBOARDS WITH THERMAL MAGNETIC, MOLDED CASE, GENERAL ELECTRIC TYPE NIAB BASED ON PRODUCTS OF THE GLIDDEN COATING & RESINS COMPANY, A DIVISION OF 2.3.4 REFER TO PROJECT DRAWINGS FOR FASCIA MATERIAL AND INSTALLATION. MATERIAL
<br /> OR APPROVED EQUAL. WITH PLUG-IN CIRCUIT BREAKERS, GENERAL ELECTRIC TYPE NLQT SCM CORPORATION. HOWEVER, EQUAL PAINTING SYSTEMS OF PRATT & LAMBERT, PPG SHALL BE ONE OF THE FOLLOWING:
<br /> OR APPROVED EQUAL PROVIDE GROUNDING FERMINAL BLOCK IN EACH PANELBOARD. INDUSTRIES AND BENJAMIN MOORE WILL BE CONSIDERED,
<br /> A, BACK-LIGHT FABRICATED SIGN SYSTEM ,y
<br /> SEE INDIVIDUAL PANEL SCHEDULE ON DRAWINGS.
<br /> 2.2 PAINTING COATS AND PRODUCTS: B. PREFINISHED METAL FASCIA SYSTEM, w Z
<br /> 2.6.2 ACCEPTABLE SUBSTITUTES: DISTRIBUTION EQUIPMENT EQUIVALENT IN TYPE,
<br /> CLASSIFICATION AND QUALITY IN ACCORDANCE WITH NEMA STANDARDS AS MANUFACTURED 2.2.1 GASOLINE ISLAND MEALS AND VENT LINES: SHALL BE. GLIUDEN SPREAD LUSTRE C. PREFIWISHED FASCIA MATERIAL AS SELECTED. n q
<br /> 8Y CUTLER-HAMMER, FEDERAL PACIFIC, ITE, SQUARE U AND WESTINGHOUSE ARE ALKYD SEMI--GLOSS PAINT #4656 ARCHITECTURAL BROWN. PART 3 - EXECUTION _
<br /> Q yv
<br /> ACCEPTABLE AS SUBSTITUTIONS, WHEN APPROVED IN WRITING 22.2 PAINT ALL MANHOLES COVERS AND 4"
<br /> SURROUNDING CONCRETE, INSIDE AND OUT, 3. 1 FABRICATION DRAWINGS: �- ' '_
<br /> PART 3 - EXECUTION IN ACCORDANCE WITH STANDARD INDUSTRY COLOR CODE AS SHOWN: w d 0
<br /> 3.1 .1 CANOPY CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING ENGINEERED AND N �`°
<br /> 3.1 GENERAL: COORDINATE TIME SCHEDULES, INSTALLATION, HOOK-UPS AND MISCELLANEOUS API COLOR CODES: Id-
<br /> PROCEDURES WITH ALL OTHER TRADES THAT WILL BE INVOLVED TO EXPEDITE THE STAMPED SHOP DRAWINGS FOR OVERHEAD STRUCTURE AND FOUNDATION SYSTEMS, _
<br /> LEADED REGULAR SOLID BLUE I
<br /> COMPLETION OF THE CONTRACT. THE ELECTRICAL SUBCONTRACTOR SHALL BE SOLEY LEADED PREMIUM SOLID RED 3.1.2 DRAWINGS SHALL SHOW PROJECT LOCATION AND ADDRESS. 3r G J
<br /> w
<br /> 3.1.3 ORIGINAL ENGINEER'S STAMP FOR APPROPRIATE STATE SHALL BE AFFIXED TO w w 0
<br /> RESPONSIBLE FOR THE PROPER INSTALLATION OF THE ELECTRICAL WORK. UNLEADED REGULAR WHITE W/BLACK CROSS
<br /> 3.2 CONDUITS: FURNISH AND INSTALL A COMPLETE OVERALL CONDUIT RACEWAY SYSTEM UNLEADED PREMIUM RED W/WHITE CROSS EACH PAGE OF DRAWINGS. w t a
<br /> o
<br /> FOR ALL WIRING AND CONDUCTORS. PROVIDE SIZES AND RACEWAYS AS INDICATED ON LEADED REGULAR W/ EXTENDER BLUE W/WHITE BAND 3.1A SHOP DRAWINGS SHALL SPECIFICALLY CALL OUT SOILS REPORT NUMBER AND DATE
<br /> UNLEADED REGULAR W EXTENDER WHITE W/BLACK CROSS & BLACK BAND FOR WHICH CANOPY FOOTINGS WERE DESIGNED.
<br /> DRAWINGS OR AS REQUIRED 8Y NATIONAL ELECTRICAL CODE FOR CONDUCTORS TO BE `� W/
<br /> EXTENDER
<br /> ALL RACEWAYS SHALL CONFORM TO THE FOLLOW REQUIREMENTS: UNLEADED PREMIUM W/EXTENDER RED W/WHITE CROSS & WHITE BAND 3.1 .5 SHOP DRAWINGS SHALL SPECIFICALLY CALL. OUT SIZE, WEIGHT, TYPE AND NUMBER
<br /> 3.2.1 CONCEAL ALL CONDUIT RUNS EXCEPT WHERE EXPOSED RUNS ARE AUTHORIZED DIESEL SOLID YELLOW OF ALL STRUCTURAL MEMBERS.
<br /> BY OWNER'S CONSTRUCTION MANAGER IN WRITING. VAPOR RECOVERY SOLID ORANGE 3.1 ,15 ALL DESIGN LOADS SHALL COMPLY WITH U.B.0 LATEST EDITION AND LOCAL
<br /> 3.2.2 ACTUAL CONDUIT RUNS AIRE NOT GENERALY INDICATED; CONDUITS AT TANKS PART 3 - EXECUTION BUILDING DEPARTMENT REQUIRED LOADINGS, WHICHEVER IS MOST STRINGENT. MINIMUM
<br /> SHALL NOT CROSS OVER TANKS. PLACE CONDUIT THROUGH EACH END OF TANK 3.1 PROTECTION: COVER ENTIRE CONCRETE SURFACES. NO PAINT OR SOLVENT SHALL BE DESIGN LOADS SHALL BE CONSIDERED i0 BE: WIND Too#, LIVE 35#, UPLIFT ,35#
<br /> EXCAVATION AND PLACE FIELDS PARALLEL WITH AXIS OF TANKS, ALLOWED TO COME IN CONTACT WITH CONCRETE SURFACES. WHERE IT BECOMES AND DEAD LOAD 35# OR AS LOCAL STRUCTURAL DESIGN DICTATES. IF APPLICATION
<br /> ii 3.2.3 CLEAN AND DRY ALL RACEWAYS THOROUGHLY BEFORE CONDUCTORS ARF. PULLED IN. NECESSARY, IN ORDER TO EXECUTE HIS OWN WORK, FOR PAINTER TO REMOVE IS SUBJECT TO HIGH ALTITUDE SNOW LOADING, DESIGN SHALL BE ADJUSTED 1"0
<br /> COMPLY ACCORDINGLY.
<br /> COVERINGS, PLATES, ETC., PLACED BY OTHER CONTRACTORS IN ANY BRANCH OF THE
<br /> 3.2.4 FLASH AND COUNTERFLASH CONDUITS WHICH PENETRATE THE CANOPY DECKING. WORK, HE SHALL REPLACE SAME IN PROPER MANNER. IN SITUATIONS WHERE SAID 3.1.7 DEFLECTION OF ALL STRUCTURAL MEMBERS SHALL BE LIMITED TO SPAN/240 FOR
<br /> w 3.2.5 PROVIDE SEAL-OFF FITTINGS WHERE CONDUIT RUNS ENTER OR LEAVE. COVERINGS, PLATES, EC., CANNOT BE READILY REMOVED, PAINTER SHALL PROTECT THE L.L. ONLY.
<br /> -� HAZARDOUS AREAS OF DISSIMILAR CONDITIONS SUCH A5 TEMPERATURE, HUMIDITY, ETC.
<br /> WORK IN SOME OTHER SATISFACTORY MANNER. OILY RAGS AND WASTE MUST BE
<br /> 3.1.8 ATTACH DECK STRUCTURAL SUPPORTS WITH 3/8 " DIAMETER BOLTS.
<br /> 3.2.6 FURNISH AND INSTALL COMPLETE RACEWAY SYSTEM, INCI-UDING CONDUITS AND REMOVED EVERY NIGHT. UNDER NO CIRCUMSTANCES SHALL THEY BE ALLOWED TO 3.1,9 ROOF DECK SHALL BE AN I.C.B.O. APPROVED DIAPHRAGM DECK AND ATTACHED IN
<br /> OUTLETS, AS INDICATED AND AS REQUIRED FOR INTERCOM SYSTEM, GAS PRICE SIGNS, ACCUMULATE, PAINTING SUBCONTRACTOR SHALL BE RESPONSIBLE FOR ANY DAMAGE DONE
<br /> SECURITY LIGHTING AND CANOPY LIGHTING SYSTEM, AND LIGHTED FASCIA SYSTEM TO THE WORK OF OTHER SUBCONTRACTORS AND SHALL REPAIR Of? REPLACE AS A MANNER THAT COULD BE CONSIDERED A DIAPHRAGM. ALTERNATE TO THIS
<br /> ) 'WHERE APPLICABLE. CONDUIT AMOUNTS AND SIZES SHALL BE AS SHOWN ON NECESSARY TO THE SATISFACTION OF THE OWNER. i/2" DIAMETER STEEL ROD DIAGONAL X-BRACING WITH TURR NBUCKLES. LAYOUT OFF
<br /> GASOLINE DRAWINGS. ADDITIONAL CONDUITS AND CIRCUITS WILL BE REQUIRED ROD BRACING AND CONNECTIONS TO STRUCTURAL MEMBERS SHALL BE APPROVED BY
<br /> 3.2 PREPARATION OF SURFACES: INSPECT ALL SURFACES TO BE PAINTED. REPORT ANY STRUCTURAL ENGINEER.
<br /> FOR LIGHTED FASCIA SYSTEMS, PROVIDE AS REQUIRED. DISCREPANCIES f0 THE CONTRACTOR PRIOR TO START OF WORK. STARTING OF PAINT
<br /> 3.1.10 CONCRETE FOOTINGS SHALL BE MADE WITH STONE AGGREGATE AND SHALL HAVE
<br /> .3.3 LIGHTING: INSTALL ALL. LIGHTING FIXTURES AND LAMPS AS INDICATED ON DRAWINGS. APPLICATION SHALL CONSTITUTE ACCEPTANCE OF SURFACES AS SUITABLE FOR THE $ _ _
<br /> A COMPRESSIVE STRENGTH TO A MINIMUM 3000 LBS. PER SQUARE INCH WITHIN 28
<br /> SECURELY MOUNT ALL FIXTURES; PROVIDE ALL ADDITIONAL HANGERSAND SUPPORTS AS RECEPTION OF PAINT APPLICATION. ALL SURFACES SHALL BE CLEAN AND DRY, BETWEEN
<br /> in NECESSARY TO SECURELY FASTEN AND SUPPORT FIXTURES. CLEAN ALL FIXTURES AND 50 AND 90 DEGREES FARENHEIT AT TIME OF PAINT APPLICATION. CLEAN METAL OF MILL DAYS AFTER POURING.
<br /> ui Q n
<br /> LAMPS UPON COMPLETION OF THE PROJECT. CONTRACTOR SHALL VERIFY AMOUNT AND SCALE, RUST, OIL, GREASE AND FOREIGN MATTER. CLEAN GALVANIZED METAL ACCORDING 3.1 .11 ALL FOUNDATION METAL. REINFORCEMENT SHALL BE DEFORMED TYPE BARS
<br /> TYPE OF ISLAND/CANOPY LIGHTING SYSTEMS. SHOULD ADDITIONAL CONDUITS/CIRCUITS TO SSPC-SP 1 -63 SOLVENT CLEANING. PROTECT ADJACENT AND FINISHED WORK FROM (EXCEPT #2 BARS) AND SHALL CONFORM TO THE REQUIREMENTS OF THE "STANDARD
<br /> BE REQUIRED, VERIFY THROUGH LOCA- CONSTRUCTION OFFICE AND PROVIDE AS REQUIRED. PAINT. SPECIFICATION A.S.T.M. 615 GRADE 40".
<br /> 3,4 SIGNS AND LIGHTED FASCIA: VERIFY FINAL_ LOCATIONS AND IYPE WITH OWNER. 3.3 APPLICATION OF PAINT: 00 NOT THIN, ADULTERATE OR CHANGE MATERIALS EXCEPT 3.1.12 THE SHOP DRAWINGS SHALL EXPLICITLY SHOW LOCATION OF DOWNSPOUTS, -
<br /> OR DAM AS RELATED TO ANY AND ALL UTILITIES AND/OR ETC.,
<br /> FURNISH AND INSTALL ALL CONDUITS AND WIRES WITH STUB-OUTS AS DIRECTED. MAKE AS RECOMMENDED BY MANUFACTURER. EMPLOY ONLY SKILLED MECHANICS FOR WORK. ALL GASOLINE VENT LINES, / 1SJUL97
<br /> FINAL CONNECTIONS AS REQUIRED. PAINTING SHALL BE BRUSHED, SPRAYED OR ROLLED EVENLY FOR THOROUGH COATS PIPING AT COLUMN LOCATIONS. ROOF DRAINS AND LEADERS SHALL BE DIRECTED
<br /> 3.5 OUTLETS: COORDINATE LOCATION OF ALL ELECTRICAL EQUIPMENT, INCLUDING IN(ERCOM WITHOUT RUNS, SAGS OR OTHER BLEMISHES. ALLOW EACH COAT TO DRY BEFORE APPLYING DOWN THE INTERIOR CANOPY COLUMN EXITING SIDE OF ISLAND FORM, LEVEL OR ABOVE PROJECT NOt
<br /> OUTLETS, SWITCHES, RECEPTACLES, CONTROLLERS, PANELBOARDS, SWITCHGEAR. ETC., TO FINISH GRADE OF CONCRETE SIDE PAD ON DOWNHILL SIDE OF ISLAND. DOWNSPOUTS SUBSEQUENT COATS. ALL SURFACES TO RECEIVE A MINIMUM OF 2 COATS AS NECESSARY TO 3028.20
<br /> AVOID INTERFERENCE AND OBSTRUCTIONS WITH EQUIPMENT OF OTHER CRAFTS AND TRADES ACHIEVE AN APPROVED FINISH. APPLICATION OF PAINT, ETC., SHALL BE IN STRICT SHALL BE 4" X 4" CONSTRUCTED OF 16 GA GALVANIZED METAL OF FREEZE-PROOF
<br /> SO THAT ELECTRICAL EQUIPMENT WILL NOT BE BLOCKED OR MADE INACCESSIBLE OR COMPLIANCE WITH MANUFACTURER'S DIRECTIONS. OR OPEN-FACE DESIGN. STRAP TO CANOPY COLUMN AT 24" O.C. DRAWN: MSP �~
<br /> INOPERABLE. PROVIDE 'WEATHERPROOFOUTLETS WHERE EXPOSED TO THE WEATHER OR 3.4 CLEAN-UP: CLEAN UP ALL DEBRIS CAUSED BY THE WORK OF THIS SECTION, KEEPING 3.1 ,13 INCLUDE IN DESIGN PROVISION FOR OVERFLOW DEVICE AT OPPOSITE CORNERS OR
<br /> To MOISTURE. THE PREMISES CLEAN AND NEAT AT ALL TIMES. CANOPY. APPROVEM CL
<br /> 3.6 ISOLATED GROUND: IT IS MANDATORY THAT GASOLINE EQUIPMENT REOUIRING ISOLATED SECTION IX 3.1.14 CONSTRUCTION NOT SPECIFICALLY INDICATED SHALL BE ACCOMPLISHED PER
<br /> CANOPIES -_-
<br /> GROUND SHALL BE PROVIDED WITH SAME. MINIMUM CIRCUITS REQUIRED, BUT NOT MINIMUM REQUIREMENTS OF THE UNIFORM BUILDING CODE, LATEST EDITION.
<br /> GHAWINO
<br /> LIMITED f0, SHALL BE: INTERCOM, GAS CONSOLE AND GASOLINE TANK MONITORING SYSTEM, 3.1.15 IF THERE ARE ANY CONFLICTS BETWEEN LINES ON DRAWINGS AND GENERAL. NOTES
<br /> :5.7 EXCAVATION AND BACKFILLING: ALL EXCAVATION AND Ba1CKFILUNC NECESSARY FOR THE PART 1 - GENERAL OR WITH SPECIFICATIONS, THE MOST STRINGENT REQUIREMENTS GOVERN. �]
<br /> w4
<br /> 1 .1 SCOPE: THIS SECTION COVERS THE FURNISHING AND INSTALLATION OF ALL ITEMS FOR %S
<br /> INSTALLATION OF ELECTRICAL WORK SHALL BE INCLUDED IN THIS SECTION Md0 COMPLY 3.1 .16 ANY DEVIATION FROM THE PLANS OR SPECIFICATIONS SHALL BE APPROVED BY F
<br /> WITH SECTION III, EARTHWORK. THE INSTALLATION OF A COMPLETE GASOLINE CANOPY INCLUDING: SOUTHLAND'S CONSTRUCTION REPRESENTATIVE.
<br />
|