INSTALL_1987 - Laserfiche WebLink

Home Browse Search

I 0 0 1 Function Key - F: Depress prior to function com- mand codes. Print Key - PRINT: Used to select copy for (1) In- ' ventory Status, (2) Shift Report, (3) Product Delivery (drop), (4) Alarm Status and (5) Last Leak Test Report. Enter the number of the report ' requested and press ENT. Silence Key - SILENCE: Used to reset remote ' alarm relays. Mode Program/Run Key: Provided with a removable key to eliminate accidental program information entry. The key is positioned in the ' Program mode for system start-up and to enter function values. When the key is positioned in the Run mode, all functions can be interrogated but no data entry values can be changed. It is ' recommended that the key is positioned in the Run mode, then removed and kept in the manager's office until a program change is re- quired. ' 6.0 PROGRAMMING INFORMATION ' Enter the set-up information into the controller by using the function codes listed in Table 6-1: Function Codes. Refer to Section 5.0 for keyboard function in- formation. IMPORTANT: The Mode key must be switched to the program position in order to enter set-up information. All system input should be preceded by activating ' Function 290. This will disable the printer and allow changes to set-up data without activating warning reports or product increases to the system's set-up ' data. When changes have been completed, activate Function 291 to restore the system to field operation. When set-up information is complete, the Mode key ' should be positioned into the Run mode and the key removed. With the Mode key positioned in the Run mode, functions can be interrogated but no set-up input can be changed. ' Information is entered by pressing the Function key, F, then pressing the correct Function Code (i.e.290). (see Table 6-1 for function code listings), and press- ing the Enter key, ENT. Then press data entry keys and your entered data will be displayed on the LCD. Now press the Enter key, ENT, to store the changes in the controller's memory. 6.1 Programming Time, Date, Station Name and Address Turn the Mode key to program and press F, 290 and the Enter key, ENT. 6.1.1 Time: Press F, 90 and ENT. Enter the cor- rect time, (i.e. 9.23.0=AM, 1=PM) and press ENT. 6.1.2 Date: Press F, 91 and ENT. Enter the cor- rect date (i.e. 1-01-90) and press ENT. Enter the correct day of the week (i.e. 1=Sun., 2=Mon., 3=Tues., etc.), press ENT. 6.1.3 Name: Press F, 94 and ENT. Enter the station's name by using the Date Entry key, (I), to advance the alphabet and Data Entry key, C/CE, to reverse the alphabet. To move right for an entry, press the Command key LO. To move to the left, press Command key HI. When the cor- rect name has been entered, press ENT. 6.1.4 Address: Press F, 95 and ENT. Enter the correct street address by using the keys described in Sections 5.0 and 6.0. 6.1.5 City, State and ZIP: Press F, 96 and ENT. Enter correct city, state and ZIP, now press ENT. Press F, 291 and ENT, to clear Calibration mode. Press PRINT, 1 and ENT, and check print- out to verify the correct time, date, name and ad- dress. No. Function 58 Display Software Revision 64 Print Set-up Values 65 Enter No. of Contacts 66 Display Contact Status 67 Set Probe Error Alarm Level 68 Manifold Tanks 69 Display Tank Information 70 Number of Tanks 71 Probe Entry 72 Initial Product (Gas) 73 Initial Product (Water) 74 Tank Type and Size 75 Leak Detect GPH Threshold 76 Hi Water Alarm Level 77 Linear Scale 78 Fuel Label 79 Theft Gallon Limit 80 Net to Gross Gallon 81 Relay #1 (Programmable) 82 Relay #2 (Programmable) 83 Relay #3 (Programmable) 84 Relay #4 (Programmable) 85 Start Leak/ Theft Detect (Manual) 86 Start Leak/Theft Detect (Manual) 87 Set-up Auto Leak Detect Mode 88 Enable and Disable Leak Detect Mode 89 Print Leak Detect Set-up Parameters 90 Time Entry 91 Date entry 93 U.S. Units to Metric 94 Station Name 95 Station Address 96 Station City and State 290 Begin Calibration and Programming Sequence 291 End Calibration and Programming Sequence Table 6.1: Function Codes.