Laserfiche WebLink
Field Installe�ng and the adhesive and mixing To seal the oval lid, first align <br /> Electrical Fittings instructions. the lid gasket to the bottom <br /> Electrical connections and of the trunk. Then seal the <br /> secondary piping can be field Sealed Turbine Enclosure gasket by tightening the wing <br /> (� installed on a turbine enclosure The sealed turbine enclosure nut positioned over the steel <br /> using optional rubber grommets is mounted and cemented to support bar. <br /> supplied by O/C TANKS. The the tank collar using the <br /> rubber grommet provides a optional adhesive(Kit AD). A minimum 3011 diameter(24" <br /> compression seal to prevent The FRP top of the sealed square) street box is required <br /> water run-off from entering the turbine enclosure is also to remove the oval lid on the <br /> piping penetration on the side cemented in place using sealed turbine enclosure after <br /> of the turbine enclosure. How- Kit AD. it is installed. <br /> ever, to prevent water infiltra- <br /> tion, grommets are not recom- Sealed turbine enclosures To leak test the sealed turbine <br /> mended for high groundwater have factory installed elec- enclosure, use a standing <br /> applications. trical fittings (four 111 NPT). water test. Air pressure tests <br /> For piping connections to the are not recommended. <br /> Secondary pipe fittings can sealed enclosure, use the <br /> also be field-installed using an optional 3" diameter FRP <br /> optional two-piece FRP cou- coupling (Kit FC-3). <br /> piing supplied by O/C TANKS. <br /> This coupling is cemented in <br /> place to provide a water-tight Grommet Kits <br /> seal for high groundwater TURBINE ENCLOSURE TURBINE ENCLOSURE <br /> applications. 101�_ EXTERIOR EXTERIOR <br /> TAPER <br /> When Used for piping COnneC- SECONDARY FRP PIPE TAPERED I.D.OF GROMMET <br /> tions, the FRP coupling and f ORS EEL ELECTRICAL FITTING ` i�_EXPANOS THE QO.TO SEAL <br /> grommet kits are designed to a <br /> provide secondary contain- <br /> ment connections only to the <br /> turbine enclosure. Do not use <br /> the grommets or FRP coupling <br /> MW°I p°acnggn <br /> for primary piping connections <br /> to the turbine enclosure. KITGE-i :Bmmm.MM,M•ODeMaloMoWatr)' <br /> GROMMET KIT GE-1 R gmmmen dr P GD e'NPT] dh 4 groin <br /> KIT EF-1 alpreaEM cougm0a 11'NPT]wllNagmmmeu(y <br /> NIT GPQRprommw for 2'00 FRP pipe <br /> Grommet Kits (••) <br /> NITGP�S 12 Bmmmae lw P 00 FRP P"1"I <br /> KITGPa 12 Bmmmee her a•OD FRP pip I—) <br /> Electrical conduit(3/4" or 111 FOOTNOTES: (9.n lmludn We and armor <br /> OD) can be installed directly Mnnclude,ninea.w.Or;uea area lmm aleadnM Mlle,In. <br /> through a grommet using Kit <br /> GE-3/4 or Kit GE-1. FRP coupling Kit TURBINE ENCLOSURE WALL <br /> (for 3"00 FRP pipe only) INTERIOR <br /> an alternate, g FEMALE SECTION NPT ADHESI <br /> threaded <br /> VE <br /> threaded couplings can be MALE SECTION <br /> installed for electrical fitting <br /> connections using Kit EF-1. �I <br /> Each KIT FC-3 includes one <br /> Optional grommet kits are also 3"coupling with adhesive. <br /> available for Installing second- Contractor Supplies 41Pe" hole saw or jig saw to cut hole. <br /> ary piping connections. The <br /> grommets are designed for 2" <br /> 3 <br />