REMOVAL_1998 - Laserfiche WebLink

Home Browse Search

-' v Awa r �IrtU JC.� CWV Irl lib Yl�q-Uy JUI`I �Iu ylb lt);ii IRAN Nominal Nominal Nominal Nominal Wan Nominal MRI Test External Pressure Random Pipe Size^' I.D. O.D. Thickness Weight Preswn-Temp. Pressure Max.Rating(pslg/MPa) Lengths (in.) (In./mm) (In./mm) (M./mm) (Ibs.-ftfkg.m) Max.Ratio ( sr ) 75' /24"C 150'F/66`C (ft./m) 2 2.235 2.375 0.070 0.4 250 osig®150'F 375 88 79 15 25 1 30 ` 56.77 60.33 1.78 0.60 1.72 MPa®66,5'C 2.59 .61 54 4.6 To 9.1 3 3.360 3.500 0.070 0.6 175 p p®150'F 300 29 24 15 25 30 85.34 88.90 1.78 0.89 1.21 MPa @ 66.5'C 2.07 .20 17 4.6 76 9.1 4 4.360 4.500 0.070 0.8 123 psig 0150'F 265 34 30 15 25 30 110.74 114.30 1.78 1.19 0.86 MPa 4 66S`C 1.83 .23 .21 4.6 7.6 9.1 Bending Radius,Minimum N na PROPERTY 2",3",4"RED THREAD"IIA Pipe Pipe Size 2' 3' 4' psi®75'F MPa®24'C Psi®75'F MPa 0 66.5'C Inches Axial Tensile(ASTM D2105) Ft. 75 105 140 Ultimate Stress 15,200 104.8 13,300 91.7 Deign Suess 31800 26.2 3,325 22.9 Modulus of Elasticity 1.80 x 10• 12411 1.4 x 10' 9653 m 22.9 32.0 42.7 Axial Compression(ASTM D695) 33,300 230.0 25,600 1770 Ultimate Stress 8,300 57.2 6,400 44.1 Design s of E 1.26 x 10' 8687 .89 x 10' 6136 (1)All values except pressure-temperature Modulus of Elasticity maximum rating are nominal values. Beam Bending(SFPTM) Tolerances or maximum/minimum limits Ultimate Stress 23,000 159.0 NA NA can be obtained from Smith Fiberglass Dec'ggnn stress19 2,900 200 1,800 12.4 Products Inc. Modulusof Elasticity 2.18 x lo' 15031 1.79 x 10' 12342 (2)All sizes can accept full vacuum pressures at (Long Term per ASTM 02925) maximum temperature ratings. (3)UL Listed 5t secondary containment piping Hyd+ostatic Bunt(ASTM D1599) and Non-UL Listed 6'secondary Ultimate Hoop containment piping are also available from Tensile Stress 35,000 241.0 41,000 283.0 Smith Fiberglass Products Inc. (4)Ultimate and allowable design stresses are Hydrostatic Design(ASTM D2992) based on minimum reinforced wall Procedure A thickness.Pipe is manufactured in cyclic 150 x 10' '" 10,450 72.1 compliance with ASTM D2996. Cycles (5)Design bending stress is 1/8 of ultimate to r account for combined stress(i.e.bending Coefficient or Unear 0.88 x 10'in./inJ"F and pressure)j. Thermal Expansion(SFPTM) 1.58 x 10'mm/mm/°C (6)For RED THREAD•ILA pipe the hydrostatic cyclic design stress was determined at 150° Specific Gravity 1.8 and 200'f,per ASTM D2992 Procedure A Flow Factor Based on this data,the extrapolated value at Hazen-Williams Coefficient 150 75'F is 13,040 psi. It is the policy of Smith Fiberglass Products to improve its products continually. In accordance with that policy, the right is reserved to make changes in specifications, descriptions and illustrative material contained in this manual as conditions warrant. The information contained herein is general In nature and Is not intended to express any warranty of any type whatsoever nor shall any be implied. Y1Yrr• ;PEI A3777 U I509001 WIIIH fEEWAAM PRODUCTS WX Little Rads,Arkereas SMITH • SMITH RBERGLASS PRODUCTS INC, A Subsidiary of A.O. Smith Corporation 2700 West 65th Stmt•Little Rock Arkansas 72209-8592•Telephone(501)5684010•FAX(501)568.4465 OCopyrfpht 1992 smith Fiberglass Produce IK. ®and'''Trademarks of Smith Hberglm Products&I PRINTED IN U.S.A. 15M1194