REMOVAL_1998 - Laserfiche WebLink

Home Browse Search

JIVJIGV J-1J 1'L:.IRULUCJI LWU111 lIV r"U"I.VJ JVII ,.,V 70 1G•Jl • rr Nominal Nominal Nominal Nominal wan Nomksal M81 Test Max------ External Pressure Pipe Siam I.D. O.D. TNtkneu WeiIgght Pressure-Temp. Pressure • Ing(Psig/MPa) pandom (Iii pin./mm) (In./mm) pn./mm) (raL4LIkg•m) M50 ax.Ratio ( ) 75' /24'C 150'F/66`C (R.Lanm) 15 2 56.77' 60.33 1.5 2.375 80 0.4 0.60 1.72 MPa066.5C 2.59 .F 375 8611 .54 46 76 901 3.360 3500 0.070 0.6 175 pipss 0150'F 300 29 24 15 2S 30 3 85.34 88.90 1.78 0.89 1.21 M e 0 66.5'C 2.07 .20 17 4.6 1 7.6 1 9.1 4 4.360 4.500 0.070 0.8 125 ppuug 0150•F 263 34 30 1 S 25 30 _ 110.74 114.30 1.78 1.19 0.86 MPa 6 656 SC 1.83 .23 .21 4.6 7.6 9.1 _ Bending Radius,Minimum N a PROPERTY 2',3',4'RED THREAD*IIA Plpe Pipe Size 2• 3' 4' pit 0 7S'F MPa 0 24'C psi 0 75'F MPa 0 66,5'C Inches Axlal Tensile(ASTM D2105) Ft. 75 105 140 Ultimate Stress 15,200 104.8 13,300 91.7 DesWn Suess 3,800 26.2 3,325 22.9 Modulus of Elasticity 1.80 x 1 P 12411 1.4 x 10' 9653 m 22.9 32.0 42.7 Axial Compression(ASTM D695) 33,300 230.0 25,600 177.0 Ultimate Stress 8,300 57.2 6,400 44.1 Desiggn Stress 1.26 x 10' 8687 .89 x 10' 6136 (1)All values except pressure-temperature ModWus of Elasticity maximum rating are nominal values. Tolerances or maximum/minimum limits Beam Bending(SFPTM) can be obtained from Smith Fiberglass Ultimate tress 23,000 159.0 NA NA Products Inc. Design a tress 2,900 20.0 1,800 12.4 (2)NI sizes can accept full vacuum pressures at Modulus of Elastic�'ty 2.18 x 10' 15031 1.79 x 10' 12342 maximum temperature ratings. (long Term per ASTM D2925) (3)UL listed 5'secondary containment plping and Non-UL Listed 6'secondary Hydrostatic Burst(ASTM D1599) containment piping are also available from Ultimate Hoop 35,000 241.0 41,000 283.0 Smith Fiberglass Products Inc Tensile Stress (4)Ultimate and allowable design stresses arc based on minimum reinforced wall Hydrostatic Design(ASTM 02992) thickness.Pipe Is manufactured in ` Procedure A m . 10,450 72.1 compliance with ASTM D2996. Cydk 1$0 x 10' (5)Design bending stress is 118 of ultimate to Cycles account for combined stress(i.e.bending coefficient of Linear 0.88 x 10'In.linJ'F and presstare. 1.58 x 10amm/mm/'C (6)For RED THR Ita pipe the Mdmstatic Thermal Expansion(SFPTM) cyclic design stress was 2992deumnProcedure u e A. and 200'F,per ASTM 02992 Procedure A rific Gravity 1.8 Based on this data,the extrapolated value at factor 75°F is 13,040 psi. Haren4MRiams Coefficient -- ISO - It is the policy Of Smith Fiberglass Products to improve its products continually. In accordance with that policy; the right is reserved to make changes in specifications, descriptions and illustrative material contained in this manual as conditions warrant. The information contained herein is general In nature and Is not intended to express any warranty of any type whatsoever nor shall any be implied. '-vPEI At 777 ED ISD 9001 SAfFH FIBERGLASS PRODUCTS INC Idose Rocl•Arkansas SMITH SMrM RBERGWS PRODUCTS INC. A Subsidiary of A.O. Smith Corporation 2700 West 65th Street is Little Rock Arkansas 72209-8592 a Telephone(501)5684010 a FAX(501)568-4465 OCopyright 1992 Smith Fiberglass Products Inc. 0 snd-Trademarks of Smith FRergiau Products Inc PRIMED IN U.S.A. 15M7194