|
�.. I-WO,
<br /> I
<br /> UST Operating Permit Application-Tank Information Instructions
<br /> (Formerly SW RCB Permit Application Form B and UPCF Form hwfwre-b)
<br /> Complete a separate farm for each UST for all new permits,permit changes,and my UST system information changes. This form must be submitted'within 30 days of
<br /> permit or UST system information changes,unless your local agency requires approval prior to making changes. For tanks that are part of a compartmentelicad unit,
<br /> each compartment is considered a separate tank and requires completion of a separate Tank Information form.For a UST permanent closure or removal,complete only
<br /> TYPE OF ACTION and Sections 1,It.111,1 V,and IN.(Note: Numbering of these instructions matches the data element numbers on the form.)
<br /> 430. TYPE OF ACTION-Check the appropriate box to indicate why this form is being submitted.
<br /> 430x. DATE UST PERMANENTLY CLOS ED-For reporting closure only:enter the date the UST was removed or closed on site.
<br /> 430b. DATE EXISTING UST DISCOVERED-Enter the date this UST was discovered.Leave blank if installation date is known.
<br /> 1. FACILITY ID NUMBER-This space is for agency use only.
<br /> 3. BUS MESS NAME-Enter the complete facility name.
<br /> 103. BUSINESS SITE ADDRESS-Enter the street address of the facility,including building number,if applicable. This address must be the physical location of
<br /> the facility.Port office box numbers are not acceptable.
<br /> 104. CITY-Enter the city or unincorporated area in which the facility is located.
<br /> 432. TANK ID R-Applicant may enter the owner's tank identification number or leave this space blank.The Local Agency will assign the State tank identification
<br /> number as the unique identifier for the lank.
<br /> 433. TANK MANUFACTURER-Enter the name of the company that manufactured the tank.
<br /> 434. TANK CONFIGURATION.Check the appropriate box to indicate if the tank is a standalone tank or one in a compartmented unit.A separate UST Operating
<br /> Permit Application-Tank Information form must be submitted for each compartment.
<br /> 435. DATE UST SYSTEM INSTALLED-Enter the date the local agency signed-off on installation of the UST system. This is the data of initial tank system
<br /> installation,and dors not include upgrades or retrofits which may have been performed later.If this is for a new installation,leave blank.
<br /> 436. TANK CAPACITY IN GALLONS:Enter the tank capacity. For compartmentalized tanks,enter data for the compartment covered by this tank form only.
<br /> 437. NUMBER OF COMPARTMENTS IN THE UNIT:If the tank is a compartmcnt,enter the total number of compartments in the unit.
<br /> 439. TANK USE-Chock the type of tank usage.
<br /> 439x. If you checked"Other"specify the type of tank usage in the space provided.
<br /> 440. TANK CONTENTS-Check the specific petroleum or non-khroleum substance stored,
<br /> 440x. If you checked"Other Petroleum"specify the common name of the substance in the space provided[i.e.,the name used in the facility's Hazardous Materials
<br /> Business Plan(HMBP)inventory).
<br /> 4406. If you checked"Other"under Non-petroleum,specify the common name of substance in the space provided(i.e..the name used in the HMBP inventory).
<br /> 443. TYPE OF TANK-Check the box that identifies the type of tank.
<br /> 444. TANK PRIMARY CONTAINMENT-Check the construction material of the primary containment(i.e., inner tank wall nearest the hazardous substance
<br /> stored). If the tank material is not listed,check"Other'and specify the material in the space provided.
<br /> 444x. If you checked"Other"specify the type of primary containment in the space provided.
<br /> 445. TANK SECONDARY CONTAINMENT-Check the construction material of the secondary containment that provides containment external to,and separate
<br /> from,the primary containment described above.If the tank is a single-wall tank,check"None." If the materiel is not listed,check'Other'and specify the
<br /> material in the space provided(e.g..HDPE).
<br /> 445a. If you checked"Other"specify the type of secondary containment in the space provided.
<br /> 452 OVERFILL PREVENTION-Check the box(es)to describe the type(s)of overfill protection equipment installed.
<br /> 458. PIPING SYSTEM TYPE-Check the type of product(waste piping installed in this tank system. "Safe suction" refers to piping systems meeting all
<br /> requirements of 23 CCR¢2636(1)(3)(also known as"European S action' 'systems)(i.e.,sloped suction piping systems with no valves or pumps below gredo
<br /> and only one cheek valve,located below and as close as practical to the suction pump). Title 23, California Code of Regulations is available online at
<br /> www.calreca com.
<br /> 460. PIPING CONSTRUCTION-Indicate if the piping is single-walled ordouble-walled,or"other".
<br /> 464. PIPING PRIMARY CONTAINMENT-Check the materials)used toconstruct the primary(i.e..inner)underground productAvaste piping.
<br /> 464x. If you checked"Othet"specify the type of primary cumainment in the space provided.
<br /> 464b. PIPING SECONDARY CONTAINMENT-Check the material(s)used to mmuract the secondary containment systems)(i,tcsi<s�tb7 P piping,tie ca)
<br /> providedforthe prodmtfwaste piping.For singIc-wall piping systems,check"None." r�
<br /> 464c. If you checked"Other'specity the type oPsecondery containment in the space provided. 1' (?
<br /> 464d. PHTNIG/TURBINE CONTAINMENT SUMP TYPE-Indicate the type ofpipingAurhine containment sump( not present.
<br /> 464eel VENT PRIMARY CONTAINMENT-Check the materiel(s)used to construct the primary(i.e.,inner)vent p ing. (Note:Address ventmgrofthetank primary
<br /> containment only.)Specify Other type of containment in the space provided. (�[(' p LU 1`t
<br /> 464f-f1 VENT SECONDARY CONTAINMENT-Check the material(s)wed toconstruct thesecendary,containmentsystem(s)(e.g;'seoarry piping,)provided for
<br /> the vent piping. For singlawall piping systems,check "None." (Note: Address venting of the tank primary containment only.) Specify Other provided
<br /> for
<br /> containment in the spam provided. pe
<br /> 464g-gl VR PRIMARY CONTAINMENT-Check the materials used to construct the rim )vapor -lN I j�.
<br /> O primary(i.e,inner vee r tacoysttyysd�ItIq s wt3houty recovery
<br /> piping(e.g,Diesel tanks),check"Nona" Specify Other"ofcontainment in thespace provided. s �'
<br /> 464h-hl VR SECONDARY CONTAINMENT-Check the material(3)used to construct the second dstend�'A'1
<br /> aro containment the space provided.
<br /> eery piping)provided for the
<br /> vapor recovery piping.For single-coal I piping systems,check"Nona." Specify Other type of containment in the space provided.
<br /> 464i. VENT PIPING TRANSITION SUMP TYPE-Indicate type of transition sump(s).Check"None'ifnot present
<br /> 464j-jl RISER PRIMARY CONTAINMENT-Check the material(s)used to construct the primary(i.e..inner)piping for all risers(not drop tubes)other than annular
<br /> space risers(i.e..risers for filling or gauging of the primary tank). Specify Other type of containment in the spew provided.
<br /> 464k-kl RISER SECONDARY CONTAINMENT-Check the material(s)used to construct secondary containment systems)(i.e..secondary piping,sumps)provided
<br /> for the riser piping For risen without secondary containment,check"None." Specify Other type of containment in did space provided.
<br /> 451ac. FILL COMPONENTS INSTALLED-Check the appropriate boxes to show that spill containment, tank bottom protection,and fill containment sumps(if
<br /> applicable)are installed.
<br /> 469x. UDC CONSTRUCTION TYPE-Check the box to describe the"of dispenser containment systems)(i.e.,dispenser sumps or pans). Ifthe system has no
<br /> dispensers(e.g.,standby generator tank system),check"No Dispensers" If the system has a dispenser,but no UDC,check"None".
<br /> 469b. UDC CONSTRUCTION MATERIAL-Check the box to describe the materials used to construct the UDC.
<br /> 469c. If you checked"Other"specify the construction material in the space provided.
<br /> 448. STEEL COMPONENT PROTECTION-All systems contain some steel components. Check the appropriate boxes)to describe all corrosion protection
<br /> methods used. "Isolation'means electrical isolation from soil,backfill,and groundwater. Examples include fiberglass cladding,ren-metallic secondary
<br /> containment systems which isolate steel components from the sub-surface environment,and insulating bushings.
<br /> APPLICANT SIGNATURE-The same person who signs the UST Operating Permit Application-Facility Information Form shall sign in the space provided. This
<br /> signature certifies that the signer believes that all information submitted is me and accurate,and that the UST system is compatible with the hazardous
<br /> substencestered.
<br /> 470. DATE-Enter the date the form was signed.
<br /> 471. APPLICANT NAME-Print or type the time of the person sign ins the form.
<br /> 472. APPLICANT TME-Enter the title of the person signing the form.
<br /> UPCF USI'-B-22
<br /> Rev.(1212007)
<br />
|