INSTALL_2013 - Laserfiche WebLink

Home Browse Search

ITEM#101 1/3 and 3/4 HP Fixed Speed Submersible Turbine Pump Specifications Liquid Compatibility - L-11 I lit-JAI' _ • Max.liquid viscosity:70 SSU at 60°F(15°C). A typical turbine model designation •Standard models are UL and cUL listed for has up to five components to define fuel mixtures containing up to I S%ethanol the pump being supplied as follows: or methanol,and 20%MTBE,20%ETBE or 17%TAME with gasoline. STP Basic Y - A esi •STPAG models are compatible with fuel STP= Basic Model Designation B mixtures containing up to 100%ethanol or methanol,and 20%MTBE,20%ETBE or XXXXX = Factory - 17%TAME with gasoline. Installed Options • 1/3 and 3/4 hp fixed speed models can STP model designations may include also be used with diesel fuels,fuel oils, one or more of the following kerosene,Avgas and jet fuels in a non-gelled characters in alphabetical order: A pourable state. AG=Alcohol-gasoline compatible •All wetted elastomers are made of a high (100%ethanol or methanol capable) grade,fluorocarbon Viton�compound. Note:Standard models 0%to IS% ethanol or methanol capable. Standard Features F=Floating suction adapter • 1/3 and 3/4 hp fixed speed models are (I-1/2"NPT female adapter) available in variable and fixed K= Intake filter screen length options. (IFS,factory installed to PMA) •Check valve:2-3/4"diameter fluorocarbon `R=Model R check valve Viton® seal constructed on cast aluminum (24 psi relief/22 psi reset for PLLD) body and steel backing washer. "W=Model W check valve For full diagram see page S. •Pressure relief valve:available in four (16 psi relief/13 psi reset for PPM4000) pressure relief settings,integral to check 'Note:If not otherwise specified,all Power Requirements valve.Standard model relieves at 40 psi and OP STP models supplied with • 1/3 and 3/4 hp fixed speed models resets above 35 psi. IV standard model check valve require single-phase,208-230 VAC, •Syphon:venturi-type syphon primer (40 psi relief/35 psi reset for 60 Hz incoming power. supplied with every submersible.Syphon MLD and TS-LS300) check valve and seconds syphon sold � • I/3 and 3/4 hp fixed speed models secondary YP Y = Pump MotoR incorporate a starting and running separately. Horsepower Rating capacitor,with internal bleed resistor, •Air eliminator:every submersible includes a 33= 113 hp fixed speed rated 370 Volt, IS microfarad. tank return path with one-way check valve •STP-SCI single-phase smart controllers and to provide active air elimination. 75 = 3/4 hp fixed speed STP-CBS single-phase control boxes are • Electrical disconnect electrical yoke A= Model Length" available for 1/3 and 3/4 hp pump control, for positive contractor disconnect VLI =Variable length range#1. • I/3 hp max.motor draw:4 Amps. during service. VL2=Variable length range#2. •3/4 hp max.motor draw:7 Amps. Approvals VU=Variable length range#3. Note:VL2 models fit 94%of all Pump Motor •Consult factory for known installations. • I/3 and 3/4 hp fixed speed,3450 rpm, applicable approvals. !!!= Riser Pipe Length two-stage centrifugal type pump motor Quality Certification with integral,automatic,thermal Riser pipe length is expressed as two overload protection. •Franklin Fueling Systems is an ISO 9001 numeric characters that indicate the • 1/3 hp models have a max.flow of Certified Manufacturer. total length of the riser in inches. Riser 40 gpm and a max.pressure of 28 psi. 'Viton®is a registered trademark of DuPont pipes are available from 7"to 69"in " 3/4 hp models have a max.flow of Dow Elastomers. I"increments(additional charge for 65 gpm and a max.pressure of 31 psi. risers 31"or longer). C UL US LISTED 19