|
May 18 2009 14: 38 Armour Petroleum Service 707-437-6068 p. 7
<br /> 8014, 8024, 8069 & 8069-C Adhesive Kits
<br /> and all adhesive is mixed In from the sides Installation Bulletin No. FB000 for additional
<br /> and corners of the can. A smooth uniform Installation instructions. 2. When the temperature Is between 50'F
<br /> consistency and color Indicates adequate and70°F(100/21.1OC)joint&maybe heated
<br /> mixing of the adhesive. For 8 thru 24 inch diameter pipe, a Fiber to accelerate the curing process. Below
<br /> Glass Systems hydraulic or manual come- 50°F (10°C) the joints must be heated to
<br /> If the adhesive becomes warm and begins to along is recommended. Connect two cure the adhesive. Fiber Glass Systems
<br /> set up in the container,safely dispose of the come-slongs to the pipe and pull the joint offers customized electrical heating collars
<br /> container. DO NOT USE THIS ADHESIVE together slowly while firmly hammering on for this purpose. The collars are reusable
<br /> TO BOND JOINTI the aides of the joint with a rubber mallet or and operate an standard 1101120 VAC or
<br /> 5 pound dead blow hammer, The vibrations 220/240 VAC. Refer to Bulletin Number
<br /> BONDING OPERATION from the hommarblows will aid joint look up. F8640, Manual Number F6000, or Manual
<br /> 1. Using a clean paint brush, apply a thin, Continue until Joint Insertion staps and locks Number F6300 for additional information.
<br /> uniform coat of adhesive to the bonding tight. Take care not to damage the pipe.
<br /> surfaces. First coat the bell and then the 3. When using a heat assisted curing
<br /> spigot bonding surfaces. NOTE:When using a hydraulic come-along, method do not handle or pressurize pipe
<br /> refer to Manual No, FSWO, F6618 or lei assemblies until they have cooled to
<br /> for coma-along pressure requirements, A ambient temperature,
<br /> Fiber Glass Systems strap damp kit Is also
<br /> available for pipe to lifting connections. ADHESIVE DISPOSAL: Once the adhe-
<br /> 3. To ensure Joint lock up a pen mark should sive and catalyst have been mixed and
<br /> be placed on the pipe as a Visual reference reacted, nothing can be extracted,and it Is
<br /> point. The mark Is usually made after the classified as non-hazardous material. Dis-
<br /> joint has been pushed together snugly but pose of In a normal manner as other solid
<br /> not completely made up, The mark should waste. Excess adhesive and catalyst can
<br /> Note. Completely coat both bonding be placed % to 1 Inch from the end of the be mixed, allowed to react, and disposed
<br /> surfaces of the Joint and remove any loose female side of the Joint. The joint is then of as above. If extra cane of adhesive or
<br /> paint brush bristles In the adhesive, driven together until Insertion of the male tubes of catalyst have accumulated with-
<br /> end stops. The mark is used as a visual out the other component to mix and react,
<br /> 2. Align and lock the joint. point of reference between the two halves contact your FGS regional manager.Cate-
<br /> of the joint lyst tubes, when empty are not subject to
<br /> EPA regulation and can be disposed of In
<br /> 4. Pipe or sub-assembiles may be moved a normal manner. These guidelines are
<br /> after the joints are looked up as long as based on federal regulations. State and
<br /> the joints are not loosened by excessive local regulations and ordinances should
<br /> bending or abrupt movements, be reviewed.
<br /> 5. When the joints are fully cured the
<br /> assemblies may be handled, pressurized
<br /> For 2 inch diameter pipe, insert the spigot or hydra tested per Fiber Glass Systems'
<br /> Into the bell until the tapered surfecas recommendations in Manual No. F6000
<br /> touch. Then while pushing, turn the joint "Pipe Installation Handbook' or Manual ( lioy ot �'.IbOr 4faea Sypbemo
<br /> until It locks tight. Normally, one half to a No, F5300"Green Thread Marine-Difahore + ! is o0t(dlAttIIUPsf
<br /> full tum Is needed. Hold In looked position. Installation Instructions.` tka( ltfkt, tMs
<br /> until excess adhesive squeezes out. ^ +9� °llp
<br /> ADHESIVE CURE s t o d"00 mer" arid,,
<br /> For 3 thru B inch diameter pipe, turning Is 1. The time required to fullycure an 'AU -;;gtt�fkiaaf 1th1e
<br /> not practical, so align the pipe and push adhesive joint Is dependant on the ambient ' e
<br /> unit the tapered surfaces touch. A driving temperature. The following table shows the +d(t041W`albreMON 'Itpl6at11ttd*1jsWf tj%*
<br /> force must be used to lock the joint. The time required for complete cure at specific 'Mott dolem version'hsted athtto./hvr W.
<br /> additional force can be provided by using a temperatures. fMOCCOM. The,information contallned
<br /> piece of hard wood and a hammer. hex f1.,Il;genefal In nature and is trot
<br /> Ambient Temperature vs. Jatenel'ed to ..express apy woratety; of
<br /> Threaded and Bonded"TA.B."Joints Time to Pressure . . ty ;."Otmiiyler, not,*Wtivw be
<br /> Temperature OF Time(Hours) "Pliod.
<br /> TA,B. ]Dints are available for 2 thru 6 50(100C) 1e
<br /> Inch diameter RED THREAD 11 pipe ro 60(15.8°C) 12
<br /> pipe connections. TA.Bjoint installation 70(21.1°C)
<br /> procedures follow the normal bell and spigot 'S� 9007
<br /> operetlansof cleaning,adhesive mixing,etc. 80(2e.7•C) 4
<br /> as described previously. The threads on the 90(32.3°C) 2
<br /> bonding surfaces are designed for ease of
<br /> Installation and to Improve the reliability of 110(43.3•C) 1
<br /> the bonded joint. See Fiber Glass Systems Dnp me mus n0 Pressurizeduntil •react auwas avatars
<br /> the adhesive joints aro fully cured.
<br /> ®Trademark of Vara I)P,Inc. FIBER GLASS SYSTEMS•A NATIONAL OILWELL VARCD COMPANY
<br /> ®2005, NATIONAL OILWELL VARCO 2700 W Seth ST.,LITTLE ROCK,AR 72209-501-688-4010-FAX 601-688-4485
<br /> PRINTED IN U,S.q 40MOS07 25 S.MAIN ST,SAND SPRINGS,OK 74063-818-24S-0651 •FAX 918-245.7588
<br />
|