INSTALL_1998 - Laserfiche WebLink

Home Browse Search

A O' •1 ' , K Nominal Nominal Nominal Nominal Wall Nominal Mill Test External Pressure Random Pipe$Ise"' Thickness Wei' ht Pressure-Temp. Pressure Max.Rating(psi g/MPa) (in.) (in./nm) (in./.::m) (in./:'m) (lbs:ft./:.g.m) Max.Rating (Prig) 75°F/24-C 150°F/66 (h 'C Lenggths ./m) 2.235 2.375 0.070 75 25 30 2 __ 0.4 250 psig @ 750°F 375 88 7g j ;o..: cOS3 '.�.-S ".a) !.72`.Ilia is 66.5 C 2.59 .61 .54 4.6 7.6 9.1 3 3.360 3.500 0.070 0.6 175 si 0 150'f 300 29 24 15 25 30 35.54 33.90 ;.:8 9a9 1.21 PIPS 66.5'C 2.07 .20 17 46 76 91 4 4.360 4.500 0.070 0.8 125 psig @ 150°F 265 34 30 !10.74 i i4..0 1.:3 0,56 SIP., c6.5'C 1.83 .23 .21 15 25 30 46 7.6 9.1 I Bending Radius,Minimum PROPERTY 2",3",4'RED THREAD'IIA Pipe Noe Size psi @ 75°F SIP., 2:24 C psi @ 75°F 1,1Pa @ 66.5"C ial nches 2' 3' 4' Axial Tensile(ASTM D2105) Ultimate Stress 15,200 1o4.S 13,300 91.7 FL 75 105 140 Design Stress 3,800 26.. 3,325 22.; Modulus of Elasticity 1.80 x 10' 1_'=' 1.4 x 10' 9653 m 22.9 32.0 42.7 Axial Compression(ASTM D695) 33 300 25,600 17:.0 Ultimate Stress 8,300 5,60 :-s.t Design Stress 7.26 x 10' cc:- .89 x 10` 6136 1 All values except pressure-temperature Modulus of Elasticity ( ) maximum rating are nominal values. Beam Bending(SFPTM) Tolerances or maximum/minimum limits Ultimate Stress 23,000 5Z.^ NA �A can be obtained from Smith Fiberglass Design Strew'- 2,900 '0? 1,800 12.4 Products Inc. Modulus of Elasticity 2.18 x 10' 15•.):' 1.79 x 10' 12:42 (2)All sizes can accept full vacuum pressures at (long Term per ASTM D2925) maximum temperature ratings. (3)UL Listed 5"secondary containment piping Hydrostatic Burst(ASTM D1599) and Non-UL Listed 6"secondary Ultimate Hoop 35,000 241._ 41,000 '53.0 containment piping are also available from Tensile Stress - Smith Fiberglass Products Inc. (4) Ultimate and allowable design stresses are Hydrostatic Design(ASTM D2992) based on minimum reinforced wall Procedure A thickness.Pipe is manufactured in Cyclic 150 x 10' "' 10,450 ' compliance with ASTM D2996. Cycles - (5) Design bending stress is 1/8 of ultimate to F account for combined stress(i.e.bending Coefficient of linear 0.88 z 10°in./in.r°F and pressure). Thermal Expansion(SFPTM) '..55 . 1 in ,int C (6) For RED THREAD'IIA pipe the hydrostatic cyclic design stress was determined at 150° Specific Gravity 1.8 and 200'F,per ASTM D2992 Procedure A. Flow Factor Based on this data,the extrapolated value at Hazen-Williams Coefficient ISO 75°F is 13,040 psi. It is the policy of Smith Fiberglass Products to improve its products continually. in accordance with that policy, the right is reserved to make changes in specifications, descriptions and illustrative material contained in this manual as conditions warrant. The information contained herein is general in nature and is not intended to express any warranty of any type whatsoever nor shall any be implied. PEI= A1777 . UL 1509001 smrrH FIBERGLASs PRoDUCTs INC. Little Rock,Arkansas SMITH SMITH FIBERGLASS PRODUCTS INC. A Subsidiary of A.O. Smith Corporation 2700 West 65th Street • Little Rock,Arkansas 72209-8592 • Telephone(501)568-4010 • FAX (501)568-4465 nwnl®aR� a.Copyright 1992 Smith Fiberglass Products Inc. d'and"'Trademarks of Smith Fiberglass Products Inc.