INSTALL_2013 - Laserfiche WebLink

Home Browse Search

ITEM#101 1/3 and 3/4 HP Fixed Speed Submersible Turbine Pump Specifications 11111111".112TE1111, IN Liquid Compatibility s - , •Max.liquid viscosity:70 SSU at 60"F(I5 °C). A typical turbine model designation •Standard models are UL and cUL listed for has up to five components to define fuel mixtures containing up to 15%ethanol the pump being supplied as follows: or methanol,and 20%MTBE,20%ETBE or 17%TAME with gasoline. STP XXXXX Y - A - B •STPAG models are compatible with fuel IS TP= Basic Model Designation 8 mixtures containing up to 100%ethanol or methanol,and 20%MTBE,20%ETBE or 1111N,XX= Factory 17%TAME with gasoline. Installed Options • 1/3 and 3/4 hp fixed speed models can STP model designations may include also be used with diesel fuels,fuel oils, one or more of the following kerosene,Avgas and jet fuels in a non-gelled characters in alphabetical order. A pourable state. AG=Alcohol-gasoline compatible _ •All wetted elastomers are made of a high . (100%ethanol or methanol capable) grade,fluorocarbon Viton compound. Note:Standard models 0%to 15% ethanol or methanol capable. Standard Features F= Floating suction adapter © • 1/3 and 3/4 hp fixed speed models are (I-1/2"NPT female adapter) available in variable and fixed K= Intake filter screen length options. (IFS,factory installed to PMA) •Check valve:2-3/4"diameter fluorocarbon 'R=Model R check valve Vitonw seal constructed on cast aluminum (24 psi relief/22 psi reset for PLLD) body and steel backing washer. 'W=Model W check valve For full diagram see page 5. •Pressure relief valve:available in four (16 psi relief/13 psi reset for PPM4000) pressure relief settings,integral to check 'Note:If not otherwise specified,all Power Requirements valve.Standard model relieves at 40 psi and - STP models supplied with • 1/3 and 3/4 hp fixed speed models resets above 35 psi. standard model check valve require single-phase,208-230 VAC, •Syphon:venturi-type syphon primer (40 psi relief/35 psi reset for 60 Hz incoming power. supplied with every submersible.Syphon MLD and TS-LS300) ry YP check valve and seconds syphon sold � • I/3 and 3/4 hp fixed speed models N= Pump MotoR incorporate a starting and running separately. Horsepower Rating capacitor,with internal bleed resistor, •Air eliminator:every submersible includes a 33= 1/3 hp fixed speed rated 370 Volt, 15 microfarad. tank return path with one-way check valve •STP-SCI single-phase smart controllers and to provide active air elimination. 75=3/4 hp fixed speed STP-CBS single-phase control boxes are • Electrical disconnect electrical yoke E= Model Length" available for 1/3 and 3/4 hp pump control. for positive contractor disconnect VLI =Variable length range#1. • 1/3 hp max.motor draw:4 Amps. during service. VL2=Variable length range#2. •3/4 hp max.motor draw:7 Amps. Approvals VU=Variable length range#3. Note:VL2 models fit 94%of all Pump Motor •Consult factory for known installations. • 1/3 and 3/4 hp fixed speed, 3450 rpm, applicable approvals. N= Riser Pipe Length two-stage centrifugal type pump motor Quality Certification With integral,automatic,thermal Riser pipe length is expressed as two overload protection. • Franklin Fueling Systems is an ISO 9001 numeric characters that indicate the • 1/3 hp models have a max.flow of Certified Manufacturer. total length of the riser in inches. Riser 40 gpm and a max.pressure of 28 psi. 'Viton's is a registered trademark of DuPont pipes are available from 7"to 69"in • 3/4 hp models have a max.flow of Dow Elastomers. 1"increments(additional charge for 65 gpm and a max.pressure of 31 psi. risers 31"or longer). I: UL US LISTED 19