INSTALL_1998 - Laserfiche WebLink

Home Browse Search

Y 1. RED JACKET PETROLEUM PUMPS are D. ManifoldbOAssembly available in two types,standard and AG series. The Manifold assembly shall be completely sealed type of pump required can be determined by the against product leakage into the ground and Alcohol concentration to be pumped. exterior water leakage into the storage tank. The The STANDARD SERIES Pumps are red in color discharge outlet shall be standard 2" NPT on and are designed and manufactured to be compat- models which install through 4" tank openings, ible with: and 3" NPT on models which install through 6" •100% Gasoline openings. The head shall have a built-in air •100% Diesel eliminator,line check valve,pressure relief valve •10% Ethanol/90%gasoline or diesel which relieves to 8-14 PSI on 4" models and a or minumum of 20 PSI on 6"models, and shall •10% Methanol/90%gasoline or diesel contain a built-in syphon primer when required. -Maximum alcohol concentration; 10% E The syphon systemshall be capable of drawing The AG SERIES PUMPS are orange in colorand are 25' of mercury vacuum through a venturi. The designed to be compatible with: syphon shall incorporate a syphon check valve •100% Gasoline to maintain the syphon action afterthe pump has •100% Diesel been turned off. •100% Ethanol 5. ELECTRICAL FEATURES •100% Methanol -Any Combination of the above A. ElectncMotors-4"Models The motor shall be 208/230 volt, 60 cycle, single 2. SCOPE phase, 3450 RPM, permanent split phase capaci- tance type continuous duty,rated explosion-proof in This specification sheet covers the technical require- Class 1, Group D, flammable solvents.The motor ments for submersible pumping equipment for han- windings shall be hermetically sealed against leak- dling low viscosity, volatile solvents, typically from age of product or moisture,and shall have athermal underground storage tanks,which require explosion- overload device with automatic reset built into the proof pumping equipment. motor windings for motor cut-off when motor tem- perature reaches a level which may cause damage 3. DESCRIPTION to the motor. B. Electnc Motors-6"Models Pump shall be of submersible centrifugal type which 6" motors shall be 208/230 volt, 60 cycle, single installs through a standard 4" or 6" threaded tank phase in 1-1/2 and 2 HP,3 phase in 2 HP also and opening. Size shall be from 1/3 through 5 HP,depend- in the 3 and 5 HP. All Horsepowers shall be 3450 ing upon required flow rates and head loss of a given RPM. Single phase motors shall be capacitor run piping system. (1-112 and 2 HP). All horsepower models shall be explosion-proof rated for use in Class 1, Group D, 4. MECHANICAL FEATURES flammable solvents,with hermetically sealed motor windings to protect against leakage of product or A. Pump moisture into the motor, and shall have a thermal Pump shall be two,three or five stage,depending overload device with automatic reset built into the upon required flow rate,self-lubricating and eas- motor for cut-off when motor temperature reached ily removed from the storage tank without dis- a level which may rause motor damage. connecting discharge piping.The pump and motor The single phase 1-1/2 and 2 HP models shall be assembly shall be readily separable from the supplied with a motor control box which provides pump column pipe to allow for simple field re- proper capacitors, relays and overload protection placement of the pump and motor. for the respective horsepower motor. B. impellers and Diffusers C Connections Impellers shall be either splined or keyed to the The motor shall have a quick-disconnect type male/ pump shaft to provide positive, non-slip rotation. female connector to be readily separable for servic- Diffusers shall be tightly secured to the lower ing without cutting or splicing of conducting wires. motor bearing housing to prevent rotation. Wiring connections to the motor, including the ca- C Pump intake inlet pacitor shall be disconnected by the quick-discon- Pump intake inlet shall be horizontal to prevent nect. Reconnecting motor to column pipe shall use drawing sediment from the tank bottom into the an alignment dowel pin for positive realignment of pump inlet. electrical male/female connector. 2