Laserfiche WebLink
-n-srw:w` , .,.,..- .,,4..-r ..� ...,syr+; .a i:v:wry`�. ._rve:,rtz+-`�,?'ti�}�sd!n'";'•�.,�. <br /> ' UL LISTED SECONDARY CONTAINMENT FITTINGS FOR PETROLEUM <br /> RODUCTS, ALCOHOLS, AND ALCOHOL-GASOLINE MIXTURES <br /> ULC LISTED FOR PETROLEUM PRODUCTS ONLY <br /> �. ' TERMINATION <br /> TEE 90° ELBOW 45e ELBOW SLEEVE COUPLING CONCENTRIC REDUCER <br /> F <br /> + 1D <br /> - ( A <br /> e B_ - �_ ET <br /> TERMINATION CONCENTRIC REDUCERM SADDLES <br /> WITH 3/4" NPT <br /> SIZES AVAILABLE <br /> Billed aide Oueel Threaded Side Ouilw <br /> NPTlnlemel Tefimmt) <br /> 3/4"NPT 3"x 2" 3"x 1 <br /> + TAP 4"x 2" 3"x 1 h" <br /> 4"x 3„ 3"x 1 h" <br /> d"x l" <br /> 4"x 1 h" <br /> ' Sizes available for Termination Concentric Reducers, 4"x 1'h" <br /> with and without tap:3"x 2",4"x 3",`6"x 4". <br /> SIZES PRESSURE RATINGS Bending Properties of RED THREAD II Pipe <br /> ' A B C D - E F psig at <br /> _ Minimum <br /> Size +tb" th Yeth Size 150° sanding Radm. <br /> NominalP <br /> t t6Pipe Size <br /> 76-F/24-C <br /> 3" 6 7 14 3 2th 21/2 3" 90 2" 50 k. <br /> ' 15.2 m <br /> 4" 712 8 14 3 3 2t/2 4" 80 3" 80 ft. <br /> 24.4 in <br /> V` 8 9 16 4 4 3 6"* (4) 4" 140 tL <br /> 42.7 m <br /> `NOTE:6"secondary containment finings are not UL/ULC Listed. <br /> RED THREAD II PIPE - TYPICAL PHYSICAL PROPERTIES(5)(a) <br /> ' 2"&3" Pipe 4"Pipe <br /> Property Value Value . Value Value Test Method <br /> at 750 F 11,900 psi 82.05 MPa 14,800 psi 102.04 MPa <br /> Tensile Strength-Axial at 1500 F 9,300 psi 64.12 MPa 12,100 psi 83.43 MPa ASTM D-2105 <br /> Compressive Strength at 750 F 22,700 <br /> -Axial Psi 156.51 MPa 33,300 psi 229.60 MPa ASTM i)-695 <br /> Modulus of Elasticity at 750 F 1.92 x 106 psi 1.32 x-104 MPa 2.37 x 106 psi 1.63 x 104 MPa' ASTM D-2105 in TensLDn at 1500 F 1.70 x 106 psi 1.17 x 104 MPa 1.53 x 106 psi 1.05 x 104 MPa <br /> Ultimate Hoop Tensile <br /> Strength at Burst-Avg at 75°F 44,000 psi 303.37 MPa 35,000 psi 241.32 MPa ASTM D-1599 <br /> ' Long Term Hoop Strength <br /> Cyclic Pressure at 750 F 9,140 psi 63.02 MPa 13,040 psi 89.91 MPa - ASTM D-2992 <br /> - <br /> (150x106 cycles) at 1500 F 8,020 psi psi 55.30 MPa - 10,450 72.05 MPa Procedure A <br /> � - - <br /> ' Thermal Expansion-Axial 1.09 x 10-5 in./in./0F 1.96 x 10-5 mm/mm/0C .88 x tOs in./in./0F 58 x 10-`mm/mm/0C AOSI-TM16-3 <br /> Thermal Conductivity 2.9BTU/(tL2)(hr.)(0F/in.) 0.42 W/(m)(OK) 28BTU/(tt2)(hrj(0F/in.) 0.40 W/(m)(010 - AOSI-TM16-15 <br /> Specific Gravity 1.8 1.8 1.8 1.8 ASTM D-792 <br /> low FactoL - _ - _ - - <br /> Hazen-Williams Coefficient 150 150 150 150 AOSI <br /> (1)AT'x2"redumrbushm,whichis (2)Threaded connections (3)Shaw bends should be eliminated (4)Data not available at time of (a)Pipe is manufactured in compliance <br /> notUL/ULC Usled is available for must be made with a to avoid stress concentration which printing. with ASTM D-2996.Refer to general v <br /> use with me 4"x 3"termination flexible connecton would resultin prematurepipefailure specification sheet in catalog for the <br /> concentric reduce, under pressure conditions. (5)Tests run on pipe samples. D-2996 designation code. <br /> 7 <br />