Laserfiche WebLink
Fleecible Undergro iping Manual F/e.*VV0RKS <br /> BY OPIN FUELING CONTAINMENT SYSTEMS <br /> IMPORTANT INFORMATION <br /> FOLLOW ALL INSTRUCTIONS <br /> INDEX 1.0 INTRODUCTION <br /> 1.0 Introduction The FlexWorks family of products by <br /> OPW-FCS offers a full line <br /> 2.0 Specifying Flexible Piping of flexible piping and pipe <br /> 3.0 Flexible Piping Connections connection products to provide <br /> 4.0 Flexible Pipe Accessories an environmentally safe means of !� <br /> 5.0 Installer Tools conveying fuels from underground <br /> 6.0 Pre-Installation Planning storage tanks to above ground fuel <br /> dispensers. The variety of piping <br /> 7.0 Piping Design Criteria and pipe connections available <br /> 8.0 Pipe Burial Requirements allows for a wide range of pipe <br /> 9.0 Flexible Piping Options routing options to meet any site design requirements. <br /> 10.0 Installing Duct Conduit Flexible piping has proven to be safer than conventional <br /> 11.0 Tank Sump Plumbing Trees rigid piping which requires numerous connection joints and <br /> directional fittings. In addition, flexible piping has proven to <br /> 12.0 Dispenser Sump Pipe Connections be considerably faster to install and more cost effective than <br /> 13.0 Flexible Pipe Fabrication rigid piping <br /> 14.0 Piping Connections <br /> 15.0 Test Boots 1.1 General Information <br /> 16.0 Tubing Assemblies This product manual contains useful information about <br /> 17.0 Flexible Vent Piping all types of flexible piping products and their associated <br /> 18.0 Testing &Filling Supply Pipe connections, accessories and installer tools. It is required that <br /> this manual be read prior to specifying and installing flexible <br /> 19.0 Periodic Line Leak Detection piping. The installation practices shall comply with these <br /> 20.0 Interstitial Integrity Testing installation instructions contained within this product manual <br /> 21.0 FlexWorks System Maintenance in order for the piping system warranty <br /> 22.0 Periodic Interstitial Testing to be valid. IMPORTANT:OPW-FCS system components <br /> 23.0 Problems may only be installed and serviced by a factory trained <br /> and currently certified installer in order for the product <br /> 24.0 Guide Specifications warranty to be valid. The use of non-certified personnel <br /> 25.0 Storage and Handling or any deviations from these written procedures could <br /> result in damage or leakage of the system and void the <br /> product warranty. Contact OPW-FCS's Customer Service <br /> Department for more information at 866-547-1816. <br /> IMPORTANT INFORMATION-FOLLOW ALL INSTRUCTIONS 1.2 Certifications and Approvals <br /> Please contact your OPW-FCS sales representative or OPW-FCS Each of OPW-FCS's flexible piping systems carry various <br /> customer service representative at 1-800-422-2525 for OPW-FCS global approvals based on the individual construction of each <br /> products installation procedures. All OPW-FCS literature including <br /> installation instruction sheets and manuals can be accessed type of pipe. <br /> from the OPW-FCS website at:www.opwgiobal.com. <br /> 1.2.1. UL Listings <br /> The use of non-qualified personnel or any deviations from these <br /> recommended procedures could result in damage or leakage FlexWorks double wall piping is listed <br /> of the system. <br /> with Underwriter's Laboratories(UL®) <br /> Manual Abbreviations: under file#MH 16678 and labeled as U L <br /> follows: Motor Vehicle Fuels, High Blend Jt, <br /> PS=Integral Primary/Secondary Pipe Fuels, Concentrated Fuels and Aviation <br /> NV=Normal Vent <br /> VR=Vapor Recovery and Marine. <br /> PP=Petroleum Products <br /> Pri=Primary UL Listed Fuels <br /> Sec=Secondary Below are the listed fuels that have been tested under <br /> WP=Working Pressure <br /> PC=Primary Carrier Pipe UL 971 and are warranted for use with the FlexWorks piping <br /> MV=Motor Vehicle Fuels system. <br /> 1 <br />