|
authorized , substances or components; soil or other CAUTION
<br /> surface or subsurface conditions; or fire, flood, storm, Do not remove elastic band from around float until
<br /> lightning , earthquake, accident or any other conditions, instructed to do so, as damage to valve may result .
<br /> events or circumstances beyond OPW' s control .
<br /> WARNING
<br /> THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER Failure to properly connect delivery hose and el .
<br /> WARRANTIES , EXPRESS OR IMPLIED, AND ALL OTHER bow, and /or disconnecting a liquid filled delivery
<br /> WARRANTIES INCLUDING , WITHOUT LIMITATION , THE hose or elbow will result in a hazardous spill, which
<br /> WARRANTIES OF MERCHANTABILITY AND FITNESS FOR may result in personal injury, property damage, fire,
<br /> A PARTICULAR PURPOSE , ARE HEREBY EXCLUDED . explosion , and water and soil pollution .
<br /> OPW shall have no other liability whatsoever, whether . Make sure all connections, including the hose and
<br /> based on breach of contract, negligence, gross negli - elbow connections, between storage tank and
<br /> gence, strict liability or any other claim , including , with - transport are securely coupled .
<br /> out limitation , for special , incidental , consequential or
<br /> exemplary damages or for the cost of labor, freight, ex- • Make sure the lip seal and /or all gaskets in the deliv-
<br /> cavation , clean - up, downtime, removal , reinstallation , ery elbow are properly in place to prevent spills .
<br /> loss of profit, or any other cost or charges . No person or • Do not operate with damaged or missing parts,
<br /> entity is authorized to assume on behalf of OPW any which prevent tight connections .
<br /> liability beyond this limited warranty. This limited war-
<br /> ranty is not assignable . Normal Operation : A Hose " Kick" and reduced flow
<br /> signal that the tank is full . Close transport delivery
<br /> * * Date of manufacture on this product is located on valve and drain hose into tank before disconnecting
<br /> the flat area of the valve body, under float . any hose fitting .
<br /> Overfilled Tank: Failure of the hose to drain after clos -
<br /> GENERAL INSTRUCTIONS ing the delivery valve signals an overfilled tank. Do Not
<br /> The OPW 71 SO Overfill Prevention Valve is designed for Disconnect any delivery hose fitting until the liquid lev-
<br /> tight fill , gravity drop applications to help prevent acci - el in the tank has been lowered to allow the hose to
<br /> dental or intentional overfilling of underground storage drain into the tank.
<br /> tanks . It is installed in the UST drop tube in place of a WARNING
<br /> standard drop tube . In the event you are splashed with fuel remove wet
<br /> The main 71 SO valve closes when liquid reaches the clothing immediately. Skin contact with gasoline
<br /> initial shut off point. A small bypass valve remains open can cause chemical burns and may result in inhala -
<br /> to allow the delivery hose to drain at 3 - 5 gallons per tion of vapors that may be fatal . Never go inside
<br /> minute . If the delivery truck valve is not closed after confined areas after being splashed and never go
<br /> initial shut- off, the bypass valve will close and will re - near ignition sources ,
<br /> strict all fuel delivery to ensure that the top of the tank IMPORTANT
<br /> is not wetted per EPA requirements . Determine if the underground storage tank is equipped
<br /> The 71 SO models of the 71 SO are designed to be in - with a ball float vent valve, as illustrated in Figure 24 . In
<br /> stalled with the following OPW products : Face Seal all systems, the shut- off point of the 71 SO must be
<br /> Adaptor, OPW Spill Container or Multi - port, Jack Screw reached before the ball float reduces flow to ensure
<br /> Kit, Rotatable Product Adaptor, and Product Cap . proper overfill valve operation .
<br /> IMPORTANT TOOLS NEEDED FOR INSTALLATION AND ASSEM -
<br /> Read these assembly and installation instructions com - BLY :
<br /> pletely and carefully prior to starting . Check to make 1 . 71 SO -TOOL or 71 SO -TOOLC or
<br /> sure all parts have been provided . Use only the parts
<br /> supplied ; substitution of parts may cause product fail - 71 SO-TOOLCT ( includes the following )
<br /> ure . • Sharp 3 / 16" drill bit with stop
<br /> Failure to follow instructions may cause improper prod - • Punch
<br /> uct operation or premature failure which may permit
<br /> storage tank overfill . An overfilled storage tank may NOTE : Testable 71 SO models ending with a " T" re -
<br /> create hazardous conditions and /or environmental con - quire the 71 SO -TOOLCT or modified 71 SO-TOOL or
<br /> 71 SO -TOOLC
<br /> tamination .
<br /> 2
<br />
|