INSTALL 1989 - Laserfiche WebLink

Home Browse Search

Extractor Fittings OPW 233 Series OPW 233 Series Extractor fittings allow foot valves and ball float vent �— valves to be removed from under- ground tanks without breaking up the concrete. See pg. 12 for OPW extractor wrench selection. Dimensions OPW 233-E 1'/s"Size OPW 233-E OPW 233-P Top thread 4" The OPW 233-E Extractor fitting is for The OPW 233-P Extractor f Ming has Outlet thread 1'/2" use with any 11/2" foot valve with a internal threads to accept a connecting I nlet male thread 4" maximum outside diameter of 23/4". nipple between the extractor and the Inlet female thread 1'/2" The 233-E has 4"male thread for con- tank flange, which provides an option Maximum clear I.D. nection to 4"tank flange and is gas- to adjust the elevation of the 233-P in through valve 27/8" ket-sealed to prevent loss of prime, relation to the tank. The cage of the caused by air being sucked in through 233-P is easily replaced because it is the top fitting. threadless-it is simply lifted out like a OPW 233-P 2"Size Materials bottle cork. Top thread 4" Body: cadmium plated cast iron Materials Outlet thread 2" Cap and suction stub adaptor:bronze Body: cast iron Inlet thread 4" Gasket: chromed tanned leather Cage: bronze Cage thread 2" SIZE: 1112" WT.: 20.22 lbs. Seals: buna-N O-ring Maximum clear I.D. 233-E-4040 SIZE: 2" WT.: 18.00 lbs. 233-P-6050 through valve 3'/2" OPW 233-V OPW233-VMPand The OPW 233-V Series Extractors are used to hold and 233-VP Test Plugs position the OPW 53-V Series Float Vent Valves in the undergroun_i storage tank. It is furnished complete with OPW Test Plugs are used t isolate the an extractable cage.The entire Float Vent sub-assembly tank from the vent piping system tem during can be extracted from the tank by using either an OPW tank testing. 52 or 89 Extractor Wrench, for tank testing. The 233-VP plug is used on: The OPW 233-V extractor is a single outlet extractor used M. 233-V-4420 (4" x 2") in non-manifolded vapor recovery systems, or systems 233-VM-4422 (4" x 2" x 2") such as shown on p. 7. The 233-VMP plug is used on: Materials: 233-V-4420 (4" x 2") Body: cast iron w'Duragard" coating 233-VM-4422 (4" x 2" x 2") Extractor: bronze 233-VM-6045 (4" x 2" x 3") SIZE: 4" x 2" WT.: 15.33 lbs. 233-V-4420 233-VP-6046 WT.: .78 lbs. 233-VMP-6047 WT.: 1.24lbs. OPW 233-VM Y. Dimensions The OPW 233-VM extractor is a multi-outlet extractor, „; available in 2 sizes; used in direct manifolded systems, ! 71 I233V 233VM 233VM vapor recovery, or where provision for Stage II Vapor 4420 4422 6045 Recovery is needed. - _ (Tee) (Cross) (Cross) SIZES:4" x 2" x 3" WT. 18.731bs. 233-VM-6045 '¢- Top Thread 4" 4" 4" 4" x 2" x 2" WT. 16.62 lbs. 233-VM-4422 '" Outlet Thread 2" 2" 2" All OPW 233-V series extractors are specially coated with black Duragard" coating, for improved corrosion .:. Tank Connec- resistance and easier cage removal. ;, tion Thread 4" 4" 4" 16