INSTALL 1994 PIPING - Laserfiche WebLink

Home Browse Search

_ I Extractor Fittings OPW 233 Series OPW 233 Series Extractor fittings i allow foot valves and ball float vent valves to be removed from under- ground tanks without breaking up the concrete. See pg. 12 for OPW extractor wrench selection. 1,W� F' Dimensions OPW 233-E 11/2'Size OPW 233-E OPW 233-P Top thread 4" The OPW 233-E Extractor fitting is for The OPW 233-P Extractor fitting has Outlet thread 11/2" use with any 11/2" foot valve with a internal threads to accept a connecting Inlet male thread 4" maximum outside diameter of 23/4". nipple between the extractor and the Inlet female thread 11/2" The 233-E has 4"male thread for con- tank flange, which provides an option Maximum clear I.D. nection to 4"tank flange and is gas- to adjust the elevation of the 233-P in through valve 27/8" ket-sealed to prevent loss of prime, relation to the tank. The cage of the caused by air being sucked in through 233-P is easily replaced because it is the top fitting. threadless-it is simply lifted out like a OPW 233-P 2"Size Materials bottle cork. Top thread 4" Body: cadmium plated cast iron Materials Outletthread 2" Cap and suction stub adaptor:bronze Body: cast iron Inlet thread 4" Gasket: chromed tanned leather Cage: bronze Cagethread 2" SIZE: 11/2"WT.: 20.22 lbs. Seals: buna-N O-ring Maximum clear I.D. 233-E-4040 SIZE: 2" WT.: 18.00 lbs. 233-P-6050 through valve 31/2" OPW 233-V OPW 233-VMP and The OPW 233-V Series Extractors are used to hold and 233-VP Test Plugs position the OPW 53-V Series Float Vent Valves in the OPW Test Plugs are used to isolate underground storage tank.It is furnished complete with the tank from the vent piping system an extractable cage.The entire Float Vent sub-assembly during tank testing. can be extracted from the tank by using either an OPW The 233-VP plug is used on: 52 or 89 Extractor Wrench for tank testing. 233-V-4420 (4"x 2") The OPW 233-V extractor is a single outlet extractor used 233-VM-4422 (4"x 2"x 2") in non-manifolded vapor recovery systems, or systems The 233-VMP plug is used on: such as shown on p. 7. 233-V-4420 (4"x 2") Materials: I 233-VM-4422 (4"x 2"x 2") Body: cast iron w/Duragard@ coating 233-VM-6045 (4"x 2"x 3") Extractor: bronze 233-VM-5522 (4"x 2"x 2") SIZE: 4" x 2" WT.: 15.33 lbs. 233-V-4420 233-VP-6046 WT.: .78 lbs. OPW 233–VM 233-VMP-6047 WT.: 1.24 lbs. The OPW 233-VM extractor is a multi-outlet extractor, Dimensions: available in 2 sizes; used in direct manifolded systems, vapor recovery, or where provision for Stage II Vapor 233V 233VM 233VM 233VM Recovery is needed. 4420 4422 6045 5522 (Tee) (Cross)(Cross) (Cross) SIZES:4" x 2" x 3" WT. 18.73 lbs. 233-VM-6045 Top Thread 4" 4" 4" 4" 4" x 2" x 2" WT. 16.62 lbs. 233-VM-4422 Outlet Thread 2" 2" 2" 2" All OPW 233-V series extractors are specially coated with — 1 2" 1 3" 12" black Duragard® coating, for improved corrosion Tank Connec- Ext. Ext. I Ext. Int. resistance and easier cage removal. tion Thread 4' 4' 4" 1 4"