INSTALL 1994 PIPING - Laserfiche WebLink

Home Browse Search

UL LISTED SECONDARY CONTAINMENT FITTINGS FOR PETROLEUM PRODUCTS, ALCOHOLS, AND ALCOHOL-GASOLINE MIXTURES ULC LISTED FOR PETROLEUM PRODUCTS ONLY TERMINATION TEE 90° ELBOW 45° ELBOW SLEEVE COUPLING CONCENTRIC REDUCER F A :1 0—i �g� E TERMINATION CONCENTRIC REDUCERO) SADDLES WITH 3/4"NPT SIZES AVAILABLE Belled Side Outlet Threaded Side Outlet NPT Inlernal Threads(2) u 3/4"NPT 3"x 2" 3"x 1" 4 >' + TAP 4"x 2" 3"x 11/4" —-- 4"x 3" 3"x 11/2" .s 4"x1" 4"xVA" Sizes available for Termination Concentric Reducers, 4"x 1'/z" with and without tap:3"x 2",4"x 3",*6"x 4". SIZES PRESSURE RATINGS Bending Properties of RED THREAD 11 Pipe A B C D E F psig at NornIrW MV Rad Size Radom ,a., t,e"" 1/4„ t 1/8"" Size 150° F Pipe Size 75^F/24*C 50 ft. 3" 6 7 14 3 21/2 21/2 3" 90 2" ` 80 ft. 4" 71/2 8 14 3 3 21/2 4" 80 3" 6"* 8 9 16 4 4 3 6"* 141 4" 140 n. :2- m *NOTE:6"secondary containment fittings are not UL/ULC Listed. RED THREAD II PIPE - TYPICAL PHYSICAL PROPERTIES1511"" Property a Value 2" &3" Pipe Value Value Value 4" Pipe Test Method Tensile Strength-Axial at 75° F 11,900 psi 82.05 MPa 14,800 psi 102.04 MPa ASTM D-2105 at 150° F 9,300 psi 64 12 MPa 12,100 psi 83.43 MPa Compressive Strength at 75° F 22,700 psi 156 51 MPa 33,300 psi 229 60 MPa ASTM D-695 —Axial Modulus of Elasticity at 75° F 1.92 x 106 psi 32 x 10' MPa 2.37 x 106 psi 1 63 x 104 f/1Pa ASTM D-2105 in Tension at 150° F 1.70 x 106 psi 17 x 104 MPa 1.53 x 108 psi 1 05 x 10' MPa Ultimate Hoop Tensile at 75° F 44,000 psi 303.37 MPa 35,000 psi 241.32 MPa ASTM D-1599 Strength at Burst—Avg Long Term Hoop Strength at 75° F 9,140 psi 63.02 MPa 13,040 psi 89.91 MPa ASTM D-2992 Cyclic Pressure at 150° F 8,020 psi 55.30 MPa 10,450 psi 72.05 MPa Procedure A (150x106 cycles) Thermal Expansion—Axial 1.09 x 10-5 in./in./°F 1 >6 x 10 'mm/mm,IC .88 x 10-5 in./in./OF 58 x 10 'mmr mm/-,r AOSI-TM16-3 Thermal Conductivity 2.9 BTU/(ft 2)(hr.)(°F/in.) ;-2 'N in,u'K) 2.8BTU/(ft.2)(hr.)(°F/in.) 040Wi(m)1'K) AOSI-TM16-15 Specific Gravity 1.8 8 1.8 1 8 ASTM D-792 Flow Factor Hazen-Williams Coefficient 150 __7 150 AOSI (1)A 3"x 2"reducer bushing which is (2)Threaded connections (3)Sharper bends should be eliminated (4)Data not available at time of (6)Pipe is manufactured in compliance not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing. with ASTM 0-2996.Refer to general use with the 4"x 3" termination flexible connector, would result in premature pipe failure specification sheet in catalog for the concentric reducer. under pressure conditions. (5)Tests run on pipe samples. 0-29%designation code. 7