Laserfiche WebLink
UL/ULC Listed Red Thread@ II A Piping System <br /> D THREAD IIA PIPING <br /> RED THREAD IIA Primary Piping RED THREAD 11A Secondary Containment Piping <br /> Nom . Pipe Pipe Nom. Pipe Pipe <br /> Size Part Length Size Part Length <br /> (In .1mm) Number (ft.) pn./mm) Number (ft.) <br /> 250 011020-069-1 15 3 80 011030-069-4 15 <br /> 2 50 011020-069-2 22-25 3 80 011030 .069-5 22-25 <br /> 2 50 011020-069-3 26-30 3 80 011030-069-6 26-30 <br /> 3 80 X011030-069-1 15 4 100 011040-077-5 15 <br /> 3 80 011030-069-2 22-25 4 100 011040-069-5 22-25 <br /> 3 80 011030-069-3 26-30 4 100 011040-077-6 26.30 <br /> 4 100 011040-071 -1 15 6 150 011060-120-5 15 <br /> 4 100 011040-069-2 22-25 6 0150 0110601204 22-25 <br /> 4 100 011040-071-3 26-30 6 150 011060-120-6 26-30 <br /> DIMENSIONAL DATA <br /> Nominal Nominal Mill <br /> Pipe Nominal Nominal Wall Nominal Pressure! Test External Pressure <br /> Size I.Q. O. D. Thickness Weight Temperature Pressure Max. Rating (psiglMPa) <br /> (In./min) (inJmtn) (in./mm) (in./min) pbslftlkg m) Max. Rating (psig/MPa) 75OF124°C 160OF1660C <br /> 2 2.235 2.375 .070 0.5 250 psig @ 150'F 375 85 80 <br /> 50 57 61 1 .78 0.74 1 .72 MPa (( , 66"C 259 .57 .55 <br /> 3 3.360 3.500 .070 0.7 175 psig @ 150°F 300 36 34 <br /> 80 85 90 254 1 .04 1 .21 MPa @ 660C 207 .25 .23 <br /> 4 4360 4 .560 .085 1 .2 125 psig @ 150°F 265 34 30 <br /> 100 111 1116 216 1 .79 0.86 MPa @ 66° C 1 .83 .23 .21 <br /> 6 6.408 6.678 . 135 2.4 NA 265 22 20 <br /> 150 163 170 3.43 3.51 NA 1 .83 . 15 . 14 <br /> TYPICAL PHYSICAL PROPERTIES") <br /> PROPERTY RED THREAD* 11A Pie Bending Radius, Minimum <br /> Nominal <br /> psi 75°F MPa@24"C Psi 150°F MPa E0°C Pipe <br /> Size 2" 3" 4" 6' <br /> Axial ensi ainches <br /> Ultimate Stress 10,300 71 .0 81200 56.5 204Design Stress 2,575 17 .6 21050 14.1 Ft. 75 110 140 <br /> Modulus of Elasticity 1 .82 x 106 12548 1 A2 x 106 9791 <br /> Axial Compression (ASTM D695) m 21 .3 33.5 42.7 82.2 <br /> Ultimate Stress <br /> 33300 230.0 25,600 177A <br /> 8,300 .572 61400 44.1 <br /> j Design Stress 1 .26 x 106 8687 .89 x 106 6136 <br /> Modulus of Elasticity <br /> (1) Ailvafuesexcept pressure4empemture <br /> Beam Bending (SFPTM) maximum rating are nominal values. Tolerances or <br /> Ultimate Stress 231000 159.0 19,200 132.0 maximumrminimum limns can be obtained from Smith <br /> Design Stress(' 2,900 20 .0 2,400 16.5 Fibercast. <br /> j Modulus of Elasticity 2 . 18 x 106 15031 1 .70 x 106 11721 (2) All sizes can accept tun vacuum pressures at <br /> (Long Term per ASTM D2925) maximum temperature ratings. <br /> (3) Ultimate and allowable design stresses are <br /> j Hydrostatic Burst (ASTM D1599) based on minimum reinforced wall thickness. Pipe is <br /> Ultimate Hoop34 ,OOD 234 39,200 271 manufactured in compliance Mtn ASTM D2996. <br /> Tensile Stress (4) Design bending stress is 1r8 of ultimate to <br /> 2° - 3" 2"& 3' 2°& 3" 2°g 3" account for cornhined stress (i.e. bending and <br /> Hydrostatic Design (ASTM D2992) pressure}. <br /> Procedure A 9 410(6( 64.9 7,400m 51 = (5) Design stress is based on long term cyclic fatigue <br /> Cyclic 150 x 106 4° - 6° 4"9-9 <br /> 4' - 6" 4 ` - 6" data using ASTM D2992 test method. However, all <br /> Cycles 13104014 89.931% 10,450 72. 1 testing is not complete at time of printing. <br /> (6) For RED THREAD I IA pipe the hydrostatic <br /> Coefficient of Linear 0.88 x 1041 inlinl°F cyclic design stress was determined at 150° and <br /> Thermal Expansion (SFPTM) 11A x 10°mminhnl`C 200°F, per ASTM D2992 Procedure A Based on this <br /> data, the extrapolated value at 75°F Is 134030 psi. <br /> Speck Gravity 1 .8 (7) For RED THREAD IIA pipe the hydrostatic cyclic <br /> Flow Factor design stress was determined at 75° and 200°F, per <br /> Hozen-Williams Coefficient 150 ASTM D2992 Procedure A. Based on this data, the <br /> extrapolated value at 150°F Is 7,400 psi. <br /> 4 <br />