WORK PLANS - Laserfiche WebLink

Home Browse Search

LIGHT SWITCH, +48" TO TOP OF BOX • D = DIMMER • 3 = SWAY • P = PILOT SWITCH • os = LINE VOLTAGE OCCUPANCY SENSOR • T = TIMMER • VS = VACANCY SENSOR WALL MOUNT OCCUPANCY SENSOR (LINE VOLTAGE) EMERGENCY LIGHTING EXIT SIGN WITH 90 MIN BATTERY BACKUP WALL MOUNT EMERGENCY LIGHT WITH 90 MIN BATTERY BACK EXTERIOR LANDING EMERGENCY LIGHT. CONNECT TO INTERIOR EXIT SIGN FOR POWER. FIXTURES WITH INTEGRAL EMERGENCY BALLAST LIGHTING FIXTURES LINEAR FIXTURE • SQUARE = RECESSED • CIRCLE =SURFACE DOWNLIGHT, SQUARE = RECESSED WALL MOUNT CEILING EXHAUST FAN POLE MOUNT AREA LIGHT ELECTRICAL LEGEND MOUNTING HEIGHTS CONVIENCE OUTLETS, PHONE & DATA OUTLETS, +15" TO BOTTOM OF BOX SYSTEMS FURNITURE CONNECTIONS +15" TO BOTTOM OF BOXES LIGHT SWITCHES FIRE ALARM MANUAL PULL STATION SHALL NOT REQUIRE "TIGHT GRASPING, PINCHING OR TWISTING OF THE WRIST" 12" TYPICAL THERMOSTAT OR WALL PHONE FINISHED FLOOR 48" TO TOP OF BOX FINISHED CEILING AUDIBLE FIRE ALARM APPLIANCE NOT LESS THEN 90" AFF OR AT LEAST 6" BELOW CEILING VISUAL APPLIANCE TO BE NOT LESS THAN 80" AFF MIN, AND NOT MORE THAN 96" AFF TO BOTTOM TITLE 24 LIGHTING CONTROLS LIGHT SWITCH COMPONENTS OF DIMMING ROOM CONTROLLER • US = LOW VOLTAGE OCCUPANCY SENSOR (CAT 5 OR AS REQUIRED) • DRC = DIMMING ROOM CONTROLLER • PE = LOW VOLTAGE DIMMING PHOTOCELL (CAT 5 OR AS REQUIRED) • D = LOW VOLTAGE DIMMER (CAT 5 OR AS REQUIRED) • R = PLUG LOAD CONTROLLER • ADR = AUTOMATIC DEMAND RESPOSNE (FOR BUILDINGS OVER 10,000 SF) BASIC LIGHTING CONTROLS NOTES: 1. FOR SUBMITTAL INCLUDE FACTORY CONTROL DRAWINGS. 2. CONDUCT A CONTROLS PRE-CONSTRUCTION MEETING WITH CONTROLS STARTUP TEAM. PROVIDE AGENDA AND ATTENDEES AS A SUBMITTAL. INCLUDE DEVICE I.D. TAGS, PROGRAMMING, CABLE ROUTING, PROGRAM AND TIME SCHEDULES AND DATE OF PROGRAMMING AND TESTING. 3. CONTRACTOR TO HAVE SYSTEM FACTORY SUPPORT FOR START UP, PROGRAMMING AND COMMISSIONING. VERIFY OPERATIONAL HOURS WITH OWNER PRIOR TO COMMISSIONING. DRAFTING NOTATIONS KEY NOTE, SEE SCHEDULE EQUIPMENT TAG, SEE SCHEDULE REFERENCE TO A DETAIL VIEW "A" ON SHEET E-2 NEW ELECTRICAL EXISTING ELECTRICAL OR DEMOLISHED WHERE NOTED EXISTING DEVICE, TO REMAIN IN OPERATION REMOVE DEVICE, KEEP REMAINDER OF CIRCUIT IN OPERATION REMOVE, RELOCATE AND RECONNECT DEVICE ON EXISTING CIRCUIT, EXTEND CIRCUIT ELECTRICAL LEGEND N## N## A E-2 FIXTURE NOTATIONS: A,(b),C-12 FIXTURE TYPE "A", SWITCH "b", CIRCUIT C-12 (e) (E) (r) (R) (RR) TELEPHONE BACKBOARD, PROVIDE #8 GND TO SERVICE GROUND COMMUNICATIONS OUTLET, PHONE & DATA PHONE ONLY OUTLET, PREWIRED WITH CAT 5e CABLE DATA ONLY OUTLET JACK, PREWIRED WITH CAT 6 CABLE ELECTRICAL POWER COMMUNICATIONS ALL LINE VOLTAGE WIRING IN CONDUIT, SEE GENERAL NOTES TICKS = # OF #12 WIRE, SHORT = HOT, LONG = NEUTRAL, DOT = GROUND, UNLESS NOTED OTHERWISE 120V OUTLET, +18" TO BOTTOM OF BOX • S = SIGN • F = FLOOR • GFI = GROUND FAULT INTERUPTER COUNTER OUTLET QUADRUPLEX OUTLET HALF SWITCHED OUTLETS OUTLETS ON EMERGENCY SYSTEMS DUCT SMOKE DETECTOR JUCTION BOX MOTOR / DISCONNECT PANELBOARD TRANSFORMER / SWITCHBOARD AS NOTED SD XX (e)200 3 PANEL "K" (e)GROUND (e)MAIN SERVICE (e)120/208V BUS M 2"C-4#3/0+1#4 GND DANGER ARC FLASH AND SHOCK HAZARD FOLLOW ALL REQUIREMENTS IN NFPA 70E FOR SAFE WORK PRACTICES AND FOR PERSONAL PROTECTIVE EQUIPMENT ARC FLASH LABELLING REQUIREMENT: PROVIDE THE FOLLOWING LABEL AS A MINIMUM FOR COMPLIANCE WITH NFPA AND NEC ON THIS PROJECT: