Laserfiche WebLink
Date:0311212001 Time:2:56:24 PM Tom Smith Valley Associates Page 2 of 2 <br /> 3. Insert (dry)thin gasket (larger diameter first) on B-18 sleeve Fig. 2E.lafltring <br /> through flex connector(see Fig. 2). Insert flex boot through 3"ULexpogcoated <br /> flex connector till boot covers B-I Sand sleeve. Alignhoseciarlp stainless steetrinedfiose <br /> so it is concentric with fitting. clamp <br /> 3"Thin gRsket. <br /> 4. Using provided UL epoxy coated hose clamp,tighten flex boot <br /> to B-18 fitting applying a minimum of 4 ft.1b.(5.5 N-m.)torque <br /> using a 5116" socket screwdriver. 3"FR? <br /> Secondary Pipe 3"flex boot <br /> S. Single-Wall Piping. When connecting to a primary fine factory glued <br /> depending on the diameter of pipe installed,use an optional BR- <br /> 3x2 reducer. First insert(dry) <br /> Rlx2reducer. Firstinsert(dry)thin gasket(smaller dimvter first); Fig. 3 Single-WallPipingthen,slide corresponding reducer over FRP pipe and seal it using <br /> provided UL epoxy coated stainless steel hose clamp(see Fig. <br /> 3). Test flex boot up to a maximum of 5 psi. For primary line, thin <br /> please refer to pipe manufacturer instructions for maximum test gasketpressures. BR-312 mlucer�` <br /> 6. Doubte-Wall Piping. When connecting to 3" fiberglass <br /> secondarypiping,follow pipe manufacture's recom"ed"'don for UL expoxy c ted <br /> fiberglassing split couplings to 3" FRP pipe factory glued to flstainless steel <br /> Bravo ex boot.After fiberglassing the 3"pipe to split coupling <br /> wait for the reconamended time by the FRP pipe manufacture <br /> then test flex boar up to a maximum of 5 psi. For primary line. <br /> please refer to pipe m anutiucturer instructions for maximum te4 Fig. 4 Double-Wall Pinine <br /> pressures. <br /> tk.c boor <br /> 3"fiberglass <br /> MALASSEMBLY II1 <br /> Pape <br /> (double-wall piping <br /> assembly shown)Applye _ <br /> NOTE:3"Pipe may be curt <br /> sealam to is late - to length as required <br /> SCAIam}O isolate , <br /> epoxy coated <br /> stainless steel clamps <br /> 7. After a sucievssf al testi of the secondary piping system apply white <br /> vulkem to complete exterior ofthe stainless steel coated c[+rmps, <br /> approximately 1/4"thick,see above image. Let the sealant form <br /> a`skin'or barren then backfill with approved pedwavel per pipe <br /> manufacturers specifications. for single wall applications isolate <br /> epoxy coated stainless steel lifted clamps by applying vulkem as <br /> described above. <br /> WARRANTY <br /> All containment systems sold by S.Bravo Systems,Inc.arc wammtcd to be tifrcc fivm defect in material and workmanship for a period of one <br /> year from the date of purchase.This warranty will be limited to the repair and replacement of parts only,and will exclude all claims for labor or <br /> consequential damage.No other express warranties given and no affirmation of S.Bravo Systems,Inc.,or its agents and/or representatives,by <br /> words or action,will comstitutc a warranty.IT IS EXPRESSLY AGREED THAT THIS WARRANTY WILL BE IN LIEU OF ALL WARRAN- <br /> TIES OF FITNESS AND IN LIEU OF THE WARRANTY OF MERCHANTABILITY. <br /> This warranty is void if there is any evidence of modification,abuse,negligence,or improper installation.If any fittings or components,other <br /> than S.Bravo Systems approved finings or components,we used in conjunction with any S.Bravo Systems product,the warranty pertaining to <br /> these products is immediately void. <br /> S.Bravo Systems,Inc. <br /> Pail Avenue •Commerce,CA 90040 <br /> 323- ` <br /> 323-RRR-4133 • Fax: 323-98R-4123 <br /> E-mail:iuf a)sbravo.cotn•httpWwww.sbravo.com <br />