Laserfiche WebLink
UJULC Listed Red Thre IIA Piping System <br /> PRIMARY FITTING 4�° ELBOW, belled ends <br /> 90 ELBOW, belled ends <br /> fX <br /> A <br /> ix, - <br /> 2"90° ELBOW 012020-360-4 2" 45o ELBOW 012020-310-4 <br /> 3"90D ELBOW 012030-360-4 3"45° ELBOW 012030-310-4 <br /> 4"90° ELBOW 012040-360-4 4" 45o ELBOW 012040-310-4 <br /> FLANGE, belled end TEE, belled ends <br /> f :; I– <br /> M y <br /> at Y•1 1y xj n. <br /> 2" FLANGE 012020-170-4 i- <br /> 3" FLANGE 012030-170-4 2"TEE 012020-410-4 <br /> 4" FLANGE 012040-170-4 3"TEE 012030-410-4 <br /> 4"TEE 012040-410-4 <br /> Nominal <br /> Pipe Size A B C D E F O X10) X21:1? <br /> (In./trim) (InJmm) (InJinw) (InJmm) (InJmm) (In./mrra) (InJrrin)) (InJnlnl) (In./mm) (ln.honl) <br /> 2 33/8 21/4 A 43/4 3/4 D-4 Holes 25/8 6 13/8 11/2 <br /> 50 86 'e49 121 19 D-4 Hol Ps t=i 1;�? 35 .O <br /> 3 45/s 25/8 13/8 6 3/4 D-4 Holes 33/4 7112 15/8 17/8 <br /> 80 117 67 85 152 19 D-4 Holes 191 41 �a <br /> 4 51/0 25/8 1 13/8 71/2 3/4 D-4 Holes 37/8 9 1112 17/8 <br /> 100 13(7 67 5 191 19 D-4 Holes 919 3i" <br /> SLEEVE COUPLING, <br /> belled ends END CAP* I NIPPLE <br /> A�1 <br /> ' I--X— �._x t• A �I <br /> E <br /> y,'IIk L.a •�C .�� <br /> 2"SLEEVE COUPLING 012020-101-8 2"END CAP 012020-180-4 2"X4" 012020-004-5 3"x 6' 012030-006-5 <br /> 3"SLEEVE COUPLING 012030-101-8 2"x 6' 012020-006-5 3"x 8" 012030-008-5 <br /> 4'SLEEVE COUPLING 012040-101-4 2"x 8' 012020-008-5 3"x 10" 012030-010-5 <br /> 2'x 10' 012020-010-5 3'x 12' 012030-012-5 <br /> 2 x 12" 012020-012-5 4"x 6" 012040-006-4 <br /> Nominal Sleeve Coupling End Cap Nipple(Overall Length"A') 4'x 8" 012040-008-4 <br /> Pipe Size A X1(1) A X1(1) 4" 6" 8" 10" 12" <br /> (InJmm) (InJrnnl) (In.Inmi) (InJmm) (In./mm) 101.6mm 152.4mm 203.2mm 254.Dmm 304.8tran 4°x 10" 012040-0104 <br /> 2 6 2118 23/4 13/8 T t t t 4'x 12" 012040-012-4 <br /> :? X152 3: is 3i� — t t t t <br /> 3 6 23/8 <br /> t t t t <br /> 4 7 27/8 — — — t t T T <br /> 100 178 - 1 — — — T T T t <br /> *Available 2"only. (1)X dimension is a nominal makeup dimension for drawing <br /> tAvailable from stock layout only. Do not use for assembly dimensions. <br /> S <br />